steinel L 800 LED Outdoor Wall Light Instruction Manual

Information
L 800 / L 810 / L 820 S
L 800 / L 810 / L 820 SC
L 800 / L 810 C
Follow written instructions!

L 800 S / L 810 S/ L 820 S / L 800 C / L 810 C
L 800 SC / L 810 SC / L 820 SC

L 820 S / L 820 SC

About this document

Please read carefully and keep in a safe place.
• Under copyright. Reproduction either in whole or in part only with our consent.
• Subject to change in the interest of technical progress.

Symbols

| Hazard warning!
---|---
| Reference to other information in the document.

General safety precautions

Disconnect the power supply before attempting any work on the unit.

• During installation, the electric power cable is connected must not be live being connected must not be live. Therefore, switch off the power first and use a voltage tester to make sure the wiring is off-circuit.
• Installing the sensor-switched light involves work on the mains voltage supply. This work must therefore be carried out professionally in accordance with national wiring regulations and electrical operating conditions. ( e.g. DE: VDE 0100, AT: ÖVE / ÖNORM E8001-1, CH: SEV 1000 )

 L 800 S / L 810 S / L 820 S /

L 800 C / L 810 C / L 800 SC /
L 810 SC / L 820 SC

1. Light enclosure
2. Wall mount
3. Bottom cover
4. Top cover
5. Mains lead concealed wiring
6. Mains lead, surface wiring
7. Mounting hook to simplify installation /cable strain relief grips
8. Spacers for surface wiring
9. House number panel (L 820 S / L 820 SC)
10. Retaining screws for house number panel (L 820 S / L 820 SC)
11. Reach setting (S only)
12. Time setting (S only)
13. Twilight setting (S only)
14. Program setting (S only)
15. Manual override function

Principle

Sensor-switched light with an active motion detector. The integrated UHF sensor emits high-frequency electromagnetic waves ( 5.8 GHz ) and receives their echo. Any movement by persons in the light’s detection zone is noticed by the sensor as a change in echo. A microprocessor then issues the switch command “switch light ON”. Detection is possible through doors, panes of glass, or thin walls. (L 800 C / L 800 SC / L 810 C / L 810 SC / L 820 SC)

The functions of the sensor-switched light can be beset via smartphone and tablet or control dial. Bluetooth interconnection is only possible via smartphone or tablet. (L 800 SC / L 800 C / L 810 SC / L 810 C / L 820 SC)

Detection zones for wall mounting:

1. Minimum reach ( 1 m )
2. Maximum reach ( 5 m )

Note:
If lights are mounted too close together, switching errors may occur as the high-frequency signals emitted will interfere with each other (Fig. A).

The following measures will help to avoid switching errors of this kind:

• Allow a distance of at least 5 m between lights.
• Interconnect lights via the Smart Remote app and selectively deactivate the sensor in individual lights via the Sensor-Off function (Fig. B + C). As a result of interconnection, movement will also switch lights ON in spite of their sensor is deactivated.

Note:
The high-frequency output of the iHF sensor is approx. 1 mW – 1.000 times less than the transmission power of a mobile phone or microwave oven.

Note:
The sensor is suitable for switching lights on automatically. Note: weather conditions may affect the way the sensor works. Strong gusts of wind, snow, rain, or hail may cause the light to come on when it is not wanted.

Electrical connection

To achieve the stated reach of 5 m, the light should be mounted at a height of approx. 2 m.
Connecting the mains power supply lead ( see diagram )
The supply lead is a three-core cable:
L = phase conductor ( usually black, brown, or grey )
N = neutral conductor ( usually blue )
PE = protective-earth conductor ( green/yellow )

If you are in any doubt, identify the conductors using a voltage tester; then disconnect from the power supply again. Phase ( L ) and the neutral conductor (N) are connected to the terminal block.

Important:
Incorrectly wired connections will produce a short circuit later on in the product or your fuse box. In this case, you must identify the individual conductors once again and
reconnect them.

Note:
The light source of this luminaire cannot be replaced. If the light source needs to be replaced ( e.g. at the end of its service life ), the complete luminaire must be replaced.

A mains power switch for turning the unit ON and OFF may of course be installed in the mains supply lead.

Functions

The sensor-switched light can be put into service after mounting the enclosure and connecting to the main power supply. When putting the light into operation manually at the light switch, it will switch OFF after 1 second for the calibration phase and is then activated for sensor mode.

It is not necessary to operate the light switch a second time.

Functions can be set via Smart Remote app (L 800 SC / L 800 C / L 810 SC / L 810 C / L 820 SC) or control dial.

Note:
The settings last selected on the control will be used.

Smart Remote app
To configure the light via smartphone or tablet, you must download the STEINEL Smart Remote app from your app store. You will need a Bluetooth- capable smartphone or tablet.

QR codes

http://www.steinel-professional.de/SmartRemote/Android/| http://www.steinel-rofessional.de/SmartRemote/iOS/

Additional functions only via the Smart Remote app:

• Main light- / basic light level adjustable
• Extended reach adjustment
• Group interconnection
• Twilight setting by teach-in

Reach setting (sensitivity ) (S only)
factory setting: 5 m
Reach is the term used to describe the semi-circular zone that is produced on the ground when mounting the light at a height of 2 m.

| – Potentiometer set to “max” = max. reach of 5 m
– Potentiometer set to “min” = min. reach of 1 m
– Potentiometer “off” = Sensor OFF
---|---

Sensor off: Motion detection and all other sensor functions are completely deactivated. We recommend selecting the shortest time ( 5 seconds ) for setting the detection zone.

Tine setting ( switch-off delay) (S only)
Factory setting: 5 s
The light’s ON time can be set to any period from approx. 5 s to a maximum of 15 min (for S) or from approx. 5 s to a maximum of. 60 min (for SC).

| Adjustment control set to::
+ = maximum time (15 min or 60 min ).
– = minimum time ( 5 s ).
---|---

Any movement detected before this time elapses will restart the timer. The shortest time setting is recommended when adjusting the detection zone and performing the functional test.

Note:
After the light switches OFF, it takes approx. 1 second before it is able to start detecting movement again. The light will only switch ON in response to movement once this period has elapsed.

Twilight setting (response threshold) (S only)
Factory setting: 2,000 lux
The light’s chosen response threshold can be infinitely varied from approx. 2 to 2,000 lux.

| Adjustment control set to:
= Daylight mode approx. 2,000 lux.
= Night-time operation approx. 2 lux.
---|---

To adjust the detection zone in daylight, the control dial must be set to 2000 lux.

Program setting (S only)

| **0 min** = Soft start / no basic lighting level ON as from the selected twilight level
**10 min**= Soft start + basic lighting level 10 minutes
**30 min**= Soft start + basic lighting level 30 minutes
= Soft start + basic lighting level all night long
---|---

Manual override function 15

If a mains switch is installed in the mains supply lead, the following functions are available in addition to simply switching the light ON and OFF:

Sensor mode15.1:
Switch light ON (when light is OFF): Switch OFF and ON once. The light stays ON for the period selected.
Switch light OFF (when light is ON): Switch OFF and ON once. Light goes out or switches to sensor mode.

Manual override15.2:

1. Activate manual override:
   Switch OFF and ON twice. The light is set to stay ON for 4 hours ( blue LED lights up behind the diffuser **4**. Then it returns automatically to sensor mode ( blue LED OFF).

2. Deactivate manual override:
   Switch OFF and ON once. Light goes out or switches to sensor operation.

Important:
The switch should be actuated in rapid succession ( in the 0.2–1-second range ).

What is soft light start?
The sensor-switched light features a soft light start function. This means that when turned ON, the light is not switched directly to maximum output but gradually builds up the brightness to 100% within the space of a second. Brightness is also gradually reduced when the light is switched OFF.

What is the basic light level?
The basic light level provides continuous nighttime illumination at approx. 10% light output. The light only switches to maximum output (100%) in response to movement in the detection zone (see Time setting l2 ). The light then returns to the basic light level (approx. 10%). The SC version switches the light to the basic light level you preselect (10-50%).

Note:
Depending on the local power grid, the LEDs may flicker slightly when dimmed. This is not a product defect and no reason for complaint.

Maintenance / care

The product requires no maintenance.
The light can be cleaned with a damp cloth ( without detergents ) if dirty.

Important note: the control gear cannot be replaced.

Disposal

Electrical and electronic equipment, accessories, and packaging must be recycled in an environmentally compatible manner.

Do not dispose of electrical and electronic equipment as domestic waste.

EU countries only:
Under the current European Directive on Waste Electrical and Electronic Equipment and its implementation in national law, electrical and electronic equipment no longer suitable for use must be collected separately and recycled in an environmentally compatible manner.

Declaration of Conformity

Hereby, STEINEL Vertrieb GmbH declares that the radio equipment type L 800 SC / L 800 S / L 800 C / L 810 SC / L 810 S / L 810 C / L 820 SC / L 820 S is in compliance with Directive 2014/53/ EU. The full text of the EU declaration of conformity is available at the following internet address: www.steinel.de

Manufacturer’s Warranty

This Steinel product has been manufactured with the utmost care, tested for proper operation and safety, and then subjected to random sample inspection. Steinel guarantees that it is in perfect condition and in proper working order. The warranty period is 36 months and starts on the date of sale to the consumer. We will remedy defects caused by material flaws or manufacturing faults. The warranty will be met by repair or replacement of defective parts at our own discretion. The warranty shall not cover damage to wear parts, damage, or defects caused by improper treatment or maintenance. Further consequential damage to other objects shall be excluded.

Claims under the warranty will only be accepted if the unit is sent fully assembled and well-packed with a brief description of the fault, a receipt or invoice ( date of purchase and dealer’s stamp ) to the appropriate Service Centre.

Repair service:
If defects occur outside the warranty period or are not covered by the warranty, ask your nearest service station for the possibility of repair.

3 YEAR
MANUFACTURER’S
WARRANTY

Technical **specifications

**

Dimensions (H x W x D)| 88 x 230 x 145 mm
91 x 230x 145 mm
260 x 230 x 145 mm| (L 800S/L 800SC/L 800C)
(L810S/L810SC/L810C)
(L 820S / L 820 SC)
---|---|---
Material| Light enclosure: Light diffuser:| aluminium plastic
Power supply| 220 – 240 V. 50/60 Hz
Power consumption (Pon)| 7.50 W
9.80W
9.80 W| (L800S/L800SC/L800C)
(L 810S/L 810SC/L 810C)
(L 820 S / L 820 SC)
Power consumption of iHF sensor| 0.61 W (SC / C only)
Light output| 4661m
6791m
679 Im| (L800S/L8COSC/L800C)
(L810S/ L810SC/ L 810C)
(L 820 S / L 820 SC)
Efficiency| 62 Im/W
69 Irn/W
69 Im/W| (L 800 S / L 800 SC/ L 800 C)
(L8108/ L810SC/ L 810C)
(L 820 S / L 820 SC)
Colour rendering index| Ra = 82
Standby network (Pnet)| 0.40 W (SC / C only)
Power factor| 0.89
Color temperature| 3000 K (warm white)
Average rated life expectancy (L70B50 at 25 °C)| > 60.000 hours
Angle of coverage| 160° with Sneak-by guard (SC / S only)
Detection reach| 1 – 5 m ((SC / C only)
Twilight setting| 2-2,000 Lux
For C: only in combination with a Bluetooth sensor-switched product
Time setting| For SC: 5 s – 60 min
For S: 5 s – 15 min
For C: only in combination with a Bluetooth sensor-switched product
Basic light level| For S: 0 %, 10 % (can only be set by adjustment contro4 For SC: 0 %, 10 – 50 % (with optional Smart Remote)
For C: 0 – 50 %soft start (with optional Smart Remote) and only in combination with a Bluetooth sensor-switched product
Permanent light| selectable (4 h)
IP rating| IP44
Protection class| II
Ambient temperature| -20°C to +40°C
Bluetooth frequency| 2.4 – 2.48 GHz (L 800/ L 810 / L 820 SC
Bluetooth transmitter power| 5 dBm / 3 mW (L 800 / L 810 / L 820 SC)
---|---
Sensor frequency| 5.8 GHz
Sensor transmitter power| < 1 mW
Colour consistency SDCM| Starting value: 3
Luminous intensity distribution| L 800 S / L 800 SC / L 800 CL 810 S / L 810 SC / L 810 C
L 820 S / L 820 SC
(L 800 S / L 800 SC / L 800 C)| This product contains an energy efficiency class “E’ light source
(L 810 S / L 810 SC / L 810 C) (L 820 S / L 820 SC)| This product contains an energy efficiency class “D” light source

Troubleshooting

break in the wiring
■ Short circuit| ■ Activate, change a fuse, turn ON the men switch, check the wiring with a voltage tester
■ Check connections
Sensor-switched light will not switch ON| ■ Twilight control set to night mode during daytime operation ■ Mains switch OFF
■ Fuse has tripped
■ Detection zone not correct& adjusted| ■ Reset
■ Switch ON
■ Activate, change a fuse, check connection if necessary
■ Readjust
Sensor-switched light will not switch OFF| ■ Continued movement within the detection zone| ■ Check detection zone and readjust if necessary
Sensor-switched light will not switch OFF completely| ■ Basic lighting level selected| ■ Turn program selector do] to 0
Sensor-switched light switching ON when it should not| ■ The wind is moving trees and bushes in the detection zone ■ Cars in the street are detected| ■ Change detection zone
■ Change detection zone
Large metal objects, such as cars or metal walls, in the detection zone| ■ Change detection zone| ■ e.g. park the car somewhere else
LED floodlight is not shown in the Bluetooth listing| ■ Incorrect region selected| ■ Settings
• Region EU/Regan US
Forgotten password?| | ■ After entering the wrong password: “Reset password” button; switch power sup* OFF and back ON again within 10 minutes; then re- enter the password
The app won’t start| ■ The location is not activated| ■ Activate location in smartphone settings
Settings for LED floodlight are greyed out| ■ LED floodlight is not declared as group master (slave mode)| ■ Set master floodlight
■ Declare LED floodlight as master
No Bluetooth LED floodlight found| ■ LED floodlight is not in reach
■ Bluetooth is deactivated on smartphone| ■ Check whether Bluetooth is activated on a smartphone or
reduce the distance to the product
■ Re-start search
No connection is set up from the smartphone to the LED floodlight| ■ Smartphone too close to the device
■ Smartphone not compatible with apP
■ The App version is not up to date| ■ Distance to LED floodlight at least 1.5 m
■ Use different smartphone
■ Update the Smart Remote app in the app store

STEINEL Vertrieb GmbH
Dieselstraße 80-84
33442 Herzebrock-Clarholz
Tel: +49/5245/448-188
www.steinel.de![steinel L 800 LED Outdoor Wall Light

• FIG 24](https://manuals.plus/wp-content/uploads/2022/05/steinel-L-800-LED- Outdoor-Wall-Light-FIG-24-550x404.png) Contact
  www.steinel.de/contacthttp://www.steinel.de/contact
  110081298 07/2021
  Technische Änderungen vorbehalten.
  Subject to technical modification without notice.

References

• Steinel Group | STEINEL
• International | STEINEL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>