steinel L 40 C Smart LED Outdoor Wall Light Instruction Manual

steinel L 40 C Smart LED Outdoor Wall Light

Specifications

Product Models: L 40 C, L 40 SC, L 42 C, L 42 SC

Dimensions:

• L 40 C: 229 x 201 x 105 mm
• L 40 SC: 261 x 201 x 105 mm
• L 42 C: 274 x 131 x 105 mm
• L 42 SC: 306 x 131 x 105 mm

Safety Precautions
Make sure to read and follow all safety instructions provided inthe user manual to prevent hazards related to electricity and water.

Electrical Connection
Ensure to follow the provided electrical connection diagram. Do not attempt to replace the light source; if replacement is necessary, replace the entire fixture.

Installation
Before installation, ensure the power is switched off. Follow the mounting steps provided in the manual, considering the range= and direction of motion detection.

Functionality
The product is compatible with Android and iOS devices. The default settings include a startup delay of up to 10 seconds, light intensity adjustment from 10% to 100%, and power-saving features.

About this document

Under copyright. Reproduction either in whole or in part only with our consent.

• Subject to change in the interest of technical progress.

Hazard warning!
Warning of hazards from electricity!
Warning of hazards from water!

General safety precautions

! Failure to observe these operating instructions presents hazards!
These instructions contain important information on the safe use of this product. Particular attention is drawn to potential hazards. Failure to observe this information may lead to death or serious injuries.

• Read instructions carefully.

• Follow safety advice.

• Keep instructions within easy reach.

  • Working with electrical current may produce hazardous situations. Touching live parts can result in electrical shock, burns or death.

  • Work on mains voltage must only be performed by qualified, skilled personnel.

  • National wiring regulations and electrical operating conditions must be observed (e.g. DE: VDE 0100,
    AT: ÖVE-ÖNORM E8001-1, CH: SEV 1000).

  • Only use genuine replacement parts.

System description

Proper use – L 40 SC, L 42 SC

• Sensor-switched LED light with motion detector.
• Wall mounting.
• Indoors and outdoors.

Proper use – L 40 C, L 42 C

• LED light.
• Wall mounting.
• Indoors and outdoors.

Operating principle – L 40 SC, L 42 SC

• The sensor-switched LED light contains an infrared motion detector and can only be adjusted via Bluetooth.

Operating principle – L 40 C, L 42 C
The C versions can be interconnected with other sensors via Bluetooth to extend the detection zone. They pass on the detected signals (presence and light level) via Bluetooth.
This is controlled in the sensor interconnected with other interface.

Package contents

• 1 LED light

• 3 spacers

• 3 wall plugs

• 3 screws

• 1 safety data sheet (A)

• 1 Quick start guide (B)

• 1 LED light

• 3 cover clips

• 3 spacers

• 3 wall plugs
  3 screws

• 1 safety data sheet (A)

• 1 Quick start guide (B)

• A Connecting terminal

• B Luminaire

• A Connecting terminal

• B Luminaire

• C Sensor unit

Light distribution curve

Electrical connection

Circuit diagram

The mains supply lead is a 3-core cable:

• L = phase conductor (usually black, brown or grey)
• N = neutral conductor (usually blue)
• PE = protective-earth conductor (green / yellow)

The floodlight can also be connected to the power supply downstream of a mains switch if it is ensured that the mains switch is left ON all the time.

The light source of this light cannot be replaced. If the light source needs to be replaced (e.g. at the end of its service life), the complete light must be replaced.

 Installation

Hazard from electrical power!
Touching live parts can result in electrical shock, burns or death.

• Switch OFF power and interrupt power supply.
• Using a voltage tester, check to make sure that the power supply is disconnected.
• Make sure power supply remains interrupted.

Risk of damage to property!
Mixing up connection leads may produce a short circuit.

• Identify connection leads.
• Connect the leads correctly.

Preparing for installation

• Check all components for damage. Do not use the product if it is damaged.
• Select an appropriate site to install the product.
  • Take reach into consideration.
  • Take reach and motion detection into consideration.
  • Vibration-free.
  • No obstacles in detection zone.
  • Not in explosive atmospheres.
  • Not on normally flammable surfaces.
  • Do not look into the light source from a short distance (< 30 cm).
  • Spaced at a distance of at least 50 cm from other LED lights.

Reach

Detecting motion across the direction in which a person walks

Detecting motion in the direction in which a person walks

Mounting procedure

• Check to make sure the power supply is switched OFF.
• Unscrew retaining screw.
• Unscrew cover.

• Mark drill holes.

• Drill holes (Ø 6 mm) and fit wall plugs.

• Screwing on LED light with concealed power supply lead.

• Screwing on LED light with surface-mounted power supply lead.

• Connect mains power supply lead as shown in the wiring diagram.
  “4. Electrical connection”

• Connect the luminaire to the wallholder.

• Push until you hear a click sound.

• Tight the safety bolt.

• Switch ON power supply.

• Make settings via app (SC version only).
  “6. Function”

Function

The functions can be set for the SC types.
C version functions only work in combination with a Bluetooth sensor-switched product.
Functions are set via the Steinel Connect app.

Steinel Connect app
To configure the light via smartphone or tablet, you must download the STEINEL Connect app from your app store. You will need a Bluetooth-capable smartphone or tablet.

Functions that can be set via the Steinel Connect app:

• Time setting.
• Reach setting.
• Twilight setting.
• Basic light level function.
• Main light / basic light level adjustable.
• Extended reach adjustment.
• Group interconnection.
• Twilight setting by teach-in.

Note

To rule out malfunctioning, a minimum distance of 3 m must be allowed from the Wi-Fi router and the access points.

Factory settings (state on leaving the factory)

• Reach: max.
• Main light time setting: 10 sec.
• Basic light time setting: 1 min.
• Twilight level: 2,000 lux
• Basic light dimming level: 50 %

Commissioning / power interruption
The settings and current operating status of the LED light are saved automatically in the event of power failure or disconnection from the power supply. Settings are reactivated] as soon as the mains power supply is restored.

Reach setting (sensitivity)
Reach is the term used to describe the diameter of the more or less circular detection zone produced on the ground after mounting the SensorLight at a height of 2 m.

• Set to maximum = max. reach (10 m)
• Set to minimum = min. reach (1 m)

Time setting
The time (stay-ON time) can be set to any period from approx. 10 seconds to a maximum of 60 minutes. Every movement detected re-activates the light.

Note:
After the unit switches OFF, it takes approx. 1 second before
it is able to start detecting movement again. The unit can then switch ON again in response to movement.
The shortest time setting is recommended when adjusting the detection zone and performing the functional test

Twilight setting
The response threshold (twilight) can be infinitely varied from approx. 2 to 2,000 lux.
= daylight mode (depending on ambient light level)
= night-time operation (approx. 2 lux)

The control dial must be turned to when adjusting the detection zone and performing the functional test in daylight.

Basic light level
The brightness of the basic light level setting can be varied between 10 % and 100 %.
The period for which the basic light level stays ON for can be infinitely varied between 10 seconds and 60 minutes, or set to remain ON all night.

Main light level
The brightness of the main light level setting can be varied between 10 % and 100 %.

Grouping
The unit can be operated as a separate light or several lights can be interconnected in groups via wireless communication. All lights belonging to a group operate in line with the group parameters set in the Steinel Connect app. Reach can be set individually for all lights in the lighting group.

Fade time
On switching ON, light level constantly builds up to
100 % (fade in). On switching OFF, light level is constantly reduced to 0 % (fade out). Fade-in and fade-out times are selectable

Neighbouring-light function
The neighbouring-light function can be activated and deactivated via the Steinel Connect app.
This function assigns the neighbouring groups to the active lighting group. The active group responds to activation signals from the neighbouring group assigned to it and switches to main light or basic light as defined in the settings.

Maintenance and care

The tool requires no maintenance.
Hazard from electrical power!
Contact between water and live parts can result in electric shock, burns or death.

• Only clean tool in a dry state.

Risk of damage to property!
Using the wrong cleaning product can damage the light.

• Clean tool with a moist cloth without detergent. Important note: the control gear cannot be replaced.

Disposal

Electrical and electronic equipment, accessories and packaging must be recycled in an environmentally compatible manner.

Do not dispose of electrical and electronic equipment as domestic waste!

EU countries only:
Under the current European Directive on Waste Electrical and Electronic Equipment and its implementation in national law, electrical and electronic equipment no longer suitable for use must be collected separately and recycled in an environmentally compatible manner.

Declaration of Conformity

STEINEL GmbH hereby declares that the L 40 SC/C and L 42 SC/C radio equipment type conforms to Directive 2014/53/EU.
The full wording of the EU Declaration of Conformity is availa-ble for downloading from the following Internet address: www.steinel.de

 Manufacturer’s warranty

• Manufacturer’s warranty of STEINEL GmbH, Diesel-strasse 80-84, DE-33442 Herzebrock-Clarholz, Germany

• All STEINEL products meet the highest quality standards. For this reason, we, the manufacturer, are pleased to provide you, the consumer, with a warranty under the following terms and conditions:

• The warranty covers the absence of deficiencies which are proven to be the result of a material defect or fault in manufacturing and which are reported to us immediately after detection and within the warranty period. The war-ranty shall apply to all STEINEL products sold and used in Germany – excluding STEINEL Professional products.

• You can opt for warranty cover in the form of repair or replacement which will be provided free of charge (if applicable, in the form of a successor model of the same or higher quality) or in the form of a credit note.

• The warranty period for the STEINEL product you have purchased is 3 years (5 years for products from the XLED home range) in each case from the date on which the product was purchased.
  We shall bear the shipping costs but not the transport risks involved in return shipment.|

• Statutory rights accruing from defects, gratuitousness The warranty cover described here shall be applicable in addition to the statutory rights of warranty – including special consumer protection provisions – and shall not restrict or replace them. Exercising your statutory rights in the event of defects is gratuitous.

Exemptions from the warranty
All replaceable lamps are expressly excluded from this warranty. In addition to this, the warranty shall not cover:

• any wear resulting from use or any other natural wear of product parts or any deficiencies in the STEINEL product that are attributable to wear caused by use or other natural wear,
• any improper or non-intended use of the product or any failure to observe the operating instructions,
• any unauthorised additions, alterations or other modifi-cations to the product or any deficiencies attributable to the use of accessory,
• supplementary or replacement parts which are not genuine STEINEL parts,
• any maintenance or care of products that is not carried out in accordance with the operating instructions,
• any attachment or installation that is not in accordance with STEINEL’s installation instructions,
• any damage or loss occurring in transit.

Application of German law

The warranty shall be governed by German law excluding the United Nations Convention concerning the International Sale of Goods (CISG).

Making claims
If you wish to make a warranty claim, please send your product complete and carriage paid with the original receipt of purchase, which must show the date of purchase and product designation, either to your retailer or directly to us at STEINEL (UK) Ltd. – 25 Manasty Road, Axis Park, Orton Southgate, GB- Peterborough Cambs PE2 6UP United Kingdom. For this reason, we recommend that you keep your receipt of purchase in a safe place until the warranty period expires.

Technical specifications

• Dimensions (H x W x D)

  • L 40 C: 229 x 201 x 105 mm
  • L 40 SC: 261 x 201 x 105 mm
  • L 42 C: 274 x 131 x 105 mm
  • L 42 SC: 306 x 131 x 105 mm

• Supply voltage: 220 – 240 V, 50/60 Hz

• Power consumption (Pon)

  • L 40 C: 12.90 W
  • L 40 SC: 12.90 W
  • L 42 C: 12.60 W
  • L 42 SC: 13.00 W

• Standby (network) (Pnet)

  • L 40 C: 0.44 W
  • L 40 SC: 0.42 W
  • L 42 C: 0.44 W
  • L 42 SC: 0.43 W

• Standby sensor (Psb)

  • L 40 SC: 0.42 W
  • L 42 SC: 0.43 W

• Luminous flux (360°)

  • L 40 C: 987 lm
  • L 40 SC: 1,057 lm
  • L 42 C: 990 lm
  • L 42 SC: 1,010 lm

• Efficiency

  • L 40 C: 76.5 lm/W
    L 40 SC: 81.9 lm
    L 42 C: 78.6 lm
    L 42 SC: 77.7 lm

• Colour temperature: 3,000 K (warm white)

• Colour rendering index: Ra = 82
  Average rated life expectancy:
  L70B50 at 25 °C: > 60,000 hours
  Colour consistency SDCM: initial value: 6

• Luminous intensity distribution:

Angle of coverage L 40, L 42 SC: 180°

• Transmission power: approx. 1 mW

• Reach L 40, L 42 SC: max. 10 m

• Time setting L 40, L 42 SC: 10 s – 60 min

• • Twilight setting L 40, L 42 SC: 2 – 2,000 lux
    IP rating: IP54

• Protection class: I

• Ambient temperature: -20 to +40 °C

This product contains a light source of energy efficiency class:

• L 40 C: “F”
• L 40 SC: “E”
• L 42 C: “E”
• L 42 SC: “F”

Troubleshooting

Unit without power.

• Fuse not switched ON or faulty.
• Switch ON fuse.
• Change faulty fuse.
  • Break in wiring.
• Check wiring with voltage tester.
• Short circuit in mains power supply lead.
• Check connections.
  • Any mains switch OFF
• Switch ON mains switch.

Unit does not switch ON.

• Wrong twilight setting selected.

  • Reset twilight setting.

• Mains switch OFF.

  • Turn on mains switch.

• Fuse not switched ON or faulty.

  • Switch ON fuse.
  • Change faulty fuse.

• Rapid movements being suppressed to minimise malfunctioning, or detection zone too small or incorrectly defined.

  • Check and adjust detection zone.

• Light source faulty.

  • The light source cannot be changed. Completely replace unit.
  • Unit does not switch OFF.

• Continued movement within the detection zone.

  • Check detection zone.
  • If necessary, limit or change detection zone.
    Unit switches ON when it should not.

• Floodlight not mounted for detecting movement reliably.

  • Securely mount floodlight.

• Movement occurred but not identified by the observer (movement behind wall, small object moving in immediate proximity of lamp etc.).

  • Check detection zone.
  • If necessary, limit or change detection zone.

STEINEL GmbH
Dieselstraße 80-84
33442 Herzebrock-Clarholz
Tel: +49/5245/448-188 www.steinel.de

References

• Steinel Group | STEINEL
• International | STEINEL
• STEINEL | Steinel Group

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>