BOYO VTM7012FHD 7-Inch FULL HD Digital Backup Camera Monitor User Manual

VTM7012FHD 7-Inch FULL HD Digital Backup Camera Monitor
User Manual

Please read the instruction manual completely before use and retain it for future reference

Function And Usage Of Products

Product function

1. Size: 7 inches or 9 inch HD LCD monitor
2. Screen ratio: 16:9 widescreen
3. Resolution: 1024×600
4. 3 channel HD video input, support CVBS, 720P, and 1080P video input
5. 2 channel audio input (CH1 and CH2)
6. Support 3 triggers
7. System: PAL/NTSC auto switchable
8. Power supply: DC 12V-24V
9. A mirror image can be set for each channel
10. Reverse time delay can be set
11. Parking guidelines could be set for each channel
12. Screen display menu and remote control

Product usage

This monitor uses a high-resolution TFT LCD screen, easy to install, simple connection, has no radiation, has low power consumption, flicker-free, gorgeous and vivid color, small and exquisite outlook. It can be widely used in various cars, buses, trucks, or special vehicles.

Front Shell Instruction

Panel operating instructions

1. Down key: to move down in the menu setting
2. Menu key: Press to display the OSD menu
3. Up key: to move up in the menu setting
4. Power: short press to turn on or off
5. CH1: quickly switch to AHD1, decrease the analog value in the menu setting
6. CH2: quickly switch to AHD2, increase the analog value in the menu setting
7. CH3: quickly switch to AHD3
8. Remote control window
9. Dimmer window
10. Bracket knobs

1. LOGO plate
2. Down key: to move down in the menu setting
3. Menu key: Press to display the OSD menu
4. Up key: to move up in the menu setting
5. Power: short press to turn on or off
6. CH1: quickly switch to AHD1, decrease the analog value in the menu setting
7. CH2: quickly switch to AHD2, increase the analog value in the menu setting
8. CH3: quickly switch to AHD3
9. Remote control window
10. Bracket knobs

Backshell instruction

1. Tail cable
2. Back splint

Electrical Connection Instructions

1. Black 14PIN power cable connector
2. Black 4PIN male connector: CH1 video signal input(AHD 1)
3. Black 4PIN male connector: CH2 video signal input(AHD 2)
4. Black 4PIN male connector: CH3 video signal input(AHD 3)
5. Black electronic wire: GND
6. Red or yellow electronic wire: connect to DC 12-24V positive pole
7. Brown electronic wire: trigger to CH1
8. Green electronic wire: trigger to CH2
9. Blue electronic wire: trigger to CH3

Remote Control

1. Power key: short press to turn on or off
2. VIDEO key: CH1, CH2, CH3 video channel switching, to move up in the menu setting
3. Right key: increase volume, increase analog value in the menu setting
4. MENU key: menu
5. Left key: decrease volume, decrease the analog value in the menu setting
6. MODE key: image mode switching, to move down in the menu setting

The Menu Setup Instructions

This machine can be set various parameters, and the setting method is as below.
In the state of a startup, press the “MENU” key on the remote control or on the front panel to set image setting, function, setting, and volume. Press the “MENU” key on the remote control or on the front panel to select the desired setting, and then press the direction key on the remote control or on the front panel to set the detailed parameters.

Image Setting

1. Brightness
   Press the “MENU” key and “UP” “DOWN” key to enter into the brightness option, and press “←” “→” on the remote control or “CH1” “CH2” on the front panel to adjust the screen brightness. 0-100 optional. And 50 as default. Press the “MENU” key to exit and save the parameter.

2. Contrast
   Press the “MENU” key and “UP” “DOWN” key to enter into the contrast option, and press “←” “→” on the remote control or “CH1” “CH2” on the front panel to adjust the screen contrast. 0-100 optional. And 50 as default. Press the “MENU” key to exit and save the parameter.

3. Saturation
   Press the “MENU” key and “UP” “DOWN” key to enter into the saturation option, and press “←” “→” on the remote control or “CH1” “CH2” on the front panel to adjust the screen saturation. 0-100 optional. And 50 as default. Press the “MENU” key to exit and save the parameter.

4. Reset
   Press the “MENU” key and “UP” “DOWN” key to enter into the reset option, press “←” “→” on the remote control or “CH1” “CH2” on the front panel to reset the brightness, contrast, and saturation parameters. Press the “MENU” key to exit and save the settings.

General Setting

1. Parking guideline
   Press the “MENU” key and “UP” “DOWN” key to enter into the parking guideline option (which can be separately set for each channel), press “←” “→” on the remote control or “CH1” “CH2” on the front panel to turn on or off the parking guideline. Press the “MENU” key to exit and save the settings. Off as default.

2. Reversing delay
   Press the “MENU” key and “UP” “DOWN” key to enter into reversing delay option (which can be separately set for each channel), press “←” “→” on the remote control or “CH1” “CH2” on the front panel to adjust the reversing delay time. Off and 1-10s optional. If the system is set off, then the monitor will return to the previous state
   immediately once finished reversing, and if it is set 2s, then the monitor will return to the previous state 2s later after finished reversing. Press the “MENU” key to exit and save the settings. Off as default.

System Setting

1. Language
   Press the “MENU” key and “UP” “DOWN” key to enter into the language option, and press “←” “→” on the remote control or “CH1” “CH2” on the front panel to select the desired language. Press the “MENU” key to exit and save the parameter. Simplified Chinese, Traditional Chinese, English, Japanese, Korean, and Russian are optional. English as default.

2. Auto dimmer
   Press the “MENU” key and “UP” “DOWN” key to enter into the auto-dim option, press “←” “→” on the remote control or “CH1” or “CH2” on the front panel to turn on or off the auto dimmer. Press the “MENU” key to exit and save the settings. Off as default. (Only for VTM9003FHD)

3. Upside down
   Press the “MENU” key and “UP” “DOWN” key to enter into the upside-down option, press “←” “→” on the remote control or “CH1” “CH2” on the front panel to turn on or off the upside-down function. Press the “MENU” key to exit and save the settings. On as default.

4. Mirror
   Press the “MENU” key and “UP” “DOWN” key to enter into the mirror option (which can be separately set for each channel), press “←” “→” on the remote control or “CH1” “CH2” on the front panel to turn on or off the mirror function. Press the “MENU” key to exit and save the settings. On as default.

5. Vcomdc
   Press the “MENU” key and “UP” “DOWN” key to enter into the VCOMDC option, press “←” “→” on the remote control or “CH1” “CH2” on the front panel to adjust the VCOMDC (no need for adjustment if the screen display is normal). 0-35 optional. And 0 as default. Press the “MENU” key to exit and save the settings.

Volume

Press the “MENU” key and “UP” “DOWN” key to enter into the volume option, and press “←” “→” on the remote control or “CH1” “CH2” on the front panel to adjust the volume.0-40 optional. And 20 as default. Press the “MENU” key to exit and save the parameter.

Performance Index

1. Power supply: DC 12V-24V
2. Maximum current: 12V<500mA
3. System: PAL/NTSC
4. Screen ratio: 16:9
5. Resolution: 1024R.G.B600
6. Working temperature: -20°C~70°C
7. Storage temperature: -30°C~85°C

Accessories

1. Remote control 1PC
2. Power cable 1PC
3. Adaptor 1PC
4. User manual 1PC
5. Warranty card 1PC
6. Product registration card 1PC
7. U shaped bracket 1PC
8. Sun shield 1PC
9. Allen wrench 1PC

For technical support contact888-941-3060
or email: info@visiontechamerica.com
WWW.VISIONTECHAMERICA.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>