EGO AB2000 490mm Power+ Mower Blade Suits User Manual
- June 5, 2024
- EGO
Table of Contents
EGO AB2000 490mm Power+ Mower Blade Suits
REPLACING THE BLADE
MODEL NUMBER AB2000/AB2001/AB2100/AB2101
AB2000 is compatible with EGO POWER+ 20” cordless mower
LM2000/LM2000-S/LM2020/LM2020SP/LM2000-FC/LM2000-S-FC/LM2020-FC/LM2020SP-FC;
AB2001 is compatible with EGO POWER+ 20” cordless mower
LM2020/LM2020SP/LM2020-FC/LM2020SP-FC;
AB2100/AB2101 is compatible with EGO POWER+ 21” cordless mower LM2100/
LM2100SP/LM2140SP/LM2100-FC/LM2100SP-FC/LM2140SP-FC.
Removing The Blade
WARNING: Always protect your hands by wearing heavy gloves or wrapping
the cutting edges with rags or other materials when performing any maintenance
on the mower blade. Always remove the battery pack when servicing or
transporting the mower.
NOTICE: The following tools are required for replacing the blade: 9/16”
(14mm) wrench, torque wrench, manual screwdriver or metal rod with a diameter
of 5/16” (8mm), and manual screwdriver or metal rod with a diameter
1/4”(6.35mm) or less.
-
Stop the motor; remove the battery pack from the mower.
-
Turn the mower on its side.
-
While wearing protective gloves, place a metal rod (e.g., a 3.5” length screw bit) with diameter less than 5/16” (8mm) into the fixing hole to act as a stabilizer (Fig. 1).
-
Use a 9/16 inch (14mm) wrench to turn the blade bolt counterclockwise to loosen it.
NOTICE: If the bolt rotates with the motor shaft when loosening the bolt, turn the fan by hand to align the through holes in the fan with the holes in the blade, and place another metal rod (e.g., a 3.5” length screw bit) with diameter less than 1/4 inch (6.35mm) into the aligned holes to act as another stabilizer (Fig. 2).
-
Continue using the 9/16 inch (14mm) wrench to turn the blade bolt counterclockwise to loosen it completely.
-
While wearing protective gloves, remove the bolt, outer flange and the blade (Fig. 3).
Installing The Blade
WARNING: Always protect your hands by wearing heavy gloves or wrapping
the cutting edges with rags or other materials when performing any maintenance
on the mower blade. Always remove the battery pack when servicing or
transporting the mower.
NOTICE: To re-install or replace the blade, be sure to replace the parts
in the exact order in which they were removed (Fig. 3).
- Mount the inner flange to the fan (Fig. 4).
- Mount the fan and the inner flange onto the motor shaft with the fan blade towards the deck (Fig. 5).
- While wearing protective gloves, position the blade on the inner flange with the surface stating “THIS SIDE FACING GRASS” facing toward the outside (Fig. 6).
- Align the outer flange with the shaft and assemble it in place.
- Mount the bolt into the shaft and turn it clockwise by hand to pre-tighten it.
- While still wearing protective gloves, hold the blade with one hand and turn the fan with the other hand to align the holes in the blade with the through holes in the inner flange (Fig. 7).
- Place a metal rod (e.g., a 3.5” length screw bit) with diameter less than 1/4 inch (6.35mm) into the aligned holes to act as a stabilizer. Place another metal rod (e.g., a 3.5” length screw bit) with diameter less than 5/16” (8mm) into the fixing hole to act as another stabilizer (Fig. 8).
- Use a 9/16 inch (14mm) torque wrench (not included) to tighten the bolt clockwise. The recommended torque for the blade bolt is 36-43 ft-lb (49-59Nm).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>