HALL TECHNOLOGIES ULTRA-V-1S 4K UHD HDMI Splitter/Extender over 1 CAT6 to 100m/328ft User Manual

HALL TECHNOLOGIES ULTRA-V-1S 4K UHD HDMI Splitter/Extender over 1 CAT6 to

100m/328ft

Introduction

The ULTRA-V series are a family of extenders used to extend HDMI video to one or more remote locations up to 100m (328ft) over a single CAT6 cable. The extenders support various resolutions including 1080p @ 60Hz and 4K UHD @ 30Hz. The Senders are available in three versions. ULTRA-V-1S has a single remote output, ULTRA-V-4S has four, and ULTRA-V-8S has eight. All Senders feature an HDMI input and a local HDMI “loop” output. This allows for connection of a local display, or daisy chaining the HDMI to another Sender to increase the number of remote displays. The Receivers have a single remote input, and one HDMI output for connection to a remote display.

Features

• Supports high resolution HDMI video including FHD (1920×1080), WQHD (2560×1440), and 4K UHD (3840×2160)
• Local HDMI outputs at all Senders to connect to a local display, or to daisy-chain a second ULTRA-V Sender
• 1,4, or 8 outputs to distribute video to multiple locations
• No video calibration required, no video quality reduction due to cable length.
• ULTRA-V Receivers are compatible with ULTRA-4K Sender

Package Contents

ULTRA-V-1S / -4S / -8S

• (x 1) ULTRA-V-1S / -4S / -8S
• (x 1) POWER SUPPLY (Hall P/N 511-IEC5V4AP5L, Mfg P/N 3A-186DB05)
• (x 1) USER’S MANUAL CARD

ULTRA-V-R

• (x 1) ULTRA-V-R
• (x 1) POWER SUPPLY (Hall P/N 511-IEC5V4AP5L, Mfg P/N 3A-186DB05))
• (x 1) USER’S MANUAL CARD

Setup

Installation

• Connect the HDMI Source to the ULTRA-V Sender port marked “HDMI IN” using a quality HDMI cable
• Optionally, connect HDMI Display to the ULTRA-V Sender port marked “HDMI OUT” or daisy-chain to a second ULTRA-V “HDMI IN” port
• Using CAT6 cable(s), connect the ULTRA-4K-S “OUTPUT” port(s) to the ULTRA-V-R “INPUT” port
• Connect ULTRA-V-R “HDMI OUTPUT” to a Display using a quality HDMI cable
• Once all connections have been made, apply power to the ULTRA-V Sender(s) and ULTRA-V-R Receiver(s)

NOTE
The ULTRA-V-R Receiver’s RJ45 input may also be connected to ULTRA-4K-S sender (or the RJ45 loop output on the ULTRA-4K-R Receiver). When plugged to ULTRA-4K, the Receiver will show the Video A by default. The ULTRA-V-R Receiver can be set to display Video B by the user (please contact Hall Technologies technical support for details).

DisplayPort Adapters
While HDMI is the most widely adopted video standard, there are a number of computer and display manufacturers that rely on DisplayPort for higher resolutions such as 2560 or 4K. Hall Technologies offers 4K compatible adapters to convert between these two video standards.

NOTE These adapters are unidirectional. For example, the DisplayPort to HDMI adapter cannot convert an HDMI signal to DisplayPort.

To connect to a source (PC) with Displayport output, use GC-DP-HD.

Virtually all monitors and TVs have HDMI (or DVI) inputs, but if your display only has Display port input, the following adapter converts HDMI to DP.

Connector and Indicator Functions

ULTRA-V-1S FRONT

1. 5V DC: Power input. Connect supplied 5V power supply to power Sender.
2. SERVICE: USB-Mini connection, used to restore factory defaults via PC GUI.
3. PWR/VID/ACT: Status indicators
4. PWR: This LED indicates power is applied to the unit.
5. VID: This LED is lit when HDMI video input is present.
6. ACT: This LED blinks when HDMI processor is active (normal).
7. HDMI OUT: HDMI local Output.
8. HDMI IN: HDMI Input port.

ULTRA-V-1S REAR

OUTPUT: CAT6 Output port to ULTRA-V-R Receiver.

ULTRA-V-4S / -8S FRONT

1. 5V DC: Power input. Connect supplied 5V power supply to power Sender.
2. SERVICE: USB-Mini connection, used to restore factory defaults via PC GUI.
3. PWR/VID/ACT: Status indicators
4. PWR: This LED indicates power is applied to the unit.
5. VID: This LED is lit when HDMI video input is present.
6. ACT: This LED blinks when HDMI processor is active (normal).
7. HDMI OUT: HDMI local Output.
8. HDMI IN: HDMI Input port.

ULTRA-V-4S / -8S REAR

OUTPUTS: CAT6 Output ports to ULTRA-V-R Receivers. (Note: ULTRA- V-4S has output ports 1 through 4)

ULTRA-V-R FRONT

1. 5V DC: Power input. Connect supplied 5V power supply to power Sender.
2. SERVICE: USB-Mini connection, used to restore factory defaults via PC GUI.
3. PWR/VID/ACT: Status indicators
4. PWR: This LED indicates power is applied to the unit.
5. VID: This LED is lit when HDMI video is being output.
6. ACT: This LED blinks when HDMI processor is active (normal).
7. HDMI OUT: HDMI local Output.

ULTRA-V-R REAR

INPUT: CAT6 Input port from ULTRA-V-S Sender.

Troubleshooting

If you are experiencing problems getting the ULTRA-V extender to work properly, please use the following troubleshooting suggestions.

• Ensure that all connections are secure. Check all status LEDs to ensure proper operation.
• Try resetting the system by unplugging the power supply, waiting 5 seconds and plugging it back.
• Try restoring factory defaults using the PC GUI.

NOTE There are no user-serviceable parts inside. Do not attempt to try to repair the unit yourself, as this will void your warranty.

Contacting Hall Technologies
If you determine that your ULTRA-V extender is malfunctioning, do not attempt to repair the unit. Instead, contact Hall Technologies Technical Support at 714-641-6607. To return the unit to Hall Technologies you must first get a Return Authorization (RMA) number. Package the unit carefully, if returning. We recommend that you use the original container.

Specifications

Video
Standards DVI (single link) HDMI 1.4 video specifications including 12 bit color depth, 3D video HDCP 1.4

Connectors ULTRA-V-1S ULTRA-V-8S

• ULTRA-V-1S
  • (1) HDMI Input
  • (1) HDMI Output
  • (1) RJ45 Output
  • (1) Mini-USB Service Port
  • (1) 2.0MM Locking DC Power Input
• ULTRA-V-4S
  • (1) HDMI Input
  • (1) HDMI Output
  • (4) RJ45 Outputs
  • (1) Mini-USB Service Port
  • (1) 2.0MM Locking DC Power Input
• ULTRA-V-8S
  • (1) HDMI Input
  • (1) HDMI Output
  • (8) RJ45 Outputs
  • (1) Mini-USB Service Port
  • (1) 2.0MM Locking DC Power Input
• ULTRA-V-R
  • (1) HDMI Output
  • (1) RJ45 Input
  • (1) Mini-USB Service Port
  • (1) 2.0MM Locking DC Power Input

Refresh Rates 60 Hz for resolutions upto and including HD (1920×1080) and WUXGA (1920×1200 30 Hz for resolutions above and including QHD (2560×1440)

General
Power Supply 100 VAC to 240 VAC, 47-63 Hz, External; 5 VDC Temp/humidity Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, non-condensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, non-condensing Power 5 VDC, 4.0 A Power Supply Cooling Convection Enclosure type Metal (Steel)

Safety CE
EMI/EMC CE, FCC Class A MTBF 90,000 hours (estimate) Warranty 3 years parts and labor

References

• Home - Hall Technologies

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>