HALL TECHNOLOGIES SPK-IC6 6 Inch In-Ceiling Speakers with Fire Rated Backbox User Manual
- June 4, 2024
- HALL TECHNOLOGIES
Table of Contents
HALL TECHNOLOGIES SPK-IC6 6 Inch In-Ceiling Speakers with Fire Rated
Backbox
Introduction
SPK-IC6 is a Fire Rated 40 watt In-Ceiling Speaker with a 1” titanium dome tweeter and a 6.5” Graphite cone driver with rubber surround. The SPK-IC6 includes taps for 8 ohm, 100-volt and 70-volt audio solutions and comes in a plenum fire rated back box. SPK-IC6 is perfect for K-12 classrooms, higher-ed classrooms and lecture halls, and medium to large meeting spaces. Hall Technologies designs and builds complete solutions for AV applications. In order to provide our customers with a complete solution we have to offer all the components necessary to build out the application. Many of our solutions include built-in and external audio amplifiers. We offer a modest yet powerful line of speakers to complement our audio solutions and add convenience to our customers for one stop shopping.
Features
- Titanium Dome Tweeter
- Graphite Cone
- Sensitivity to 86 dB
- Taps for 8 Ohm, 70 and 100 volts
- Magnetic Speaker Grill
- Fire-Rated Back Box
Package Contents
- Ÿ 1 x Tweeter 1” (25mm) Titanium Dome
- Ÿ 1 x Woofer 6.5” (165mm) Graphite Cone, Rubber Surround
- 1 x Cut out template grille
Optional Accessories (sold separately):
Ceiling tile bridge SPK-IC6-BRKT
Dimensions
Installation
-
STEP 1
Using a stud finder or other accurate method, locate center point between two joists and mark. Using template provided, trace hold pattern on surface of ceiling. -
STEP 2
Using a sabre saw, keyhole saw or very sharp utility knife, cut hole in ceiling. Following trace pattern. -
STEP 3
Run loudspeaker wire to sound source location. There are several methods you can use to accomplish wiring, depending on the construction characteristics of the room or house. You can add a professional touch to your installation by using a speaker terminal plate at the source location. Leave enough wire at speaker. Location (8-10 inches / 20-25 cm) to complete connection. -
STEP 4
Attach loudspeaker wires to speaker terminals, observing correct polarity and position speaker frame up into cutout. Be careful not to pinch wires in the process. -
STEP 5
Carefully tighten the four mounting screws. This will cause the mounting wings to rotate out behind the mounting surface and secure the speaker in place. -
STEP 6
After the speaker panel is secured tightly, test sound. When you are satisfied the speaker is operational, then affix grill.
Specifications
| Feature | Detail |
|---|---|
| Tweeter | 1″ (25mm) Titanium dome |
| Woofer | 6.5″ (165 mm) Graphite Cone, |
Rubber Surround
Frequency Range+/-3| 65 Hz -20KHZ
Power Handing RMS| 80 W program , 40 W ( IEEE 219 )
Sensitivity| 86 dB
Taps| 8 ,0,40W,20W,10W,5W
Impedance| 8 ohms
Termination| Standard pressed connector
Included Accessories| Cut Out template grille
Dimensions(H*D)| 9.01″ x 10.11″ (236 x 257mm)
Cut Out diameter| 8.85″ (225mm)
Certifications| CE
Attachment| Low-profile grille
Material| ABS+iron
Service
This unit has very sophisticated circuitry and should only be serviced by a
fully trained technician. This is why each unit bears the
following label:
CAUTION
To prevent electric shock,do not remove covers. No user serviceable parts
inside. Refer servicing to qualified technician.
Worldwide service Service may be obtained from your local authorized service
center.To obtain service, simply present your sales receipt as proof of
purchase along with the defective unit to an authorized service center.They
will handle the necessary paperwork and repair.
Remember to transport your unit in the original factory packaging.
-
When sending a product to authorized service center for service, be sure to fill out the service information form and include it
inside your unit s shipping pack. Do not send the service information form separately. -
To ensure the safe transportation of your unit to the authorized service center, ship it in an original factory-packing container.
-
Do not ship the unit in any kind of rack. Ignoring this warning may result in extensive damage to the unit and the equipment rack.
Accessories are not needed. Do not send the instruction manual, cables and any other hardware.
WEEE Mark
If you want to dispose of this product, do not mix with general household
waste.There are separate collection systems for used
electronic products in accordance with legislation under the WEEE Directive
(Directive 2002/96/EC) effective only within the Euro
pean Union.
© Copyright 2022. Hall Technologies All rights reserved.
1234 Lakeshore Drive Suite #150, Coppell, TX 75019 halltechav.com / [email protected] (714)641-6607