HALL TECHNOLOGIES SSW-HD-4A HDMI Seamless Switchers User Manual
- May 15, 2024
- HALL TECHNOLOGIES
Table of Contents
SSW-HD-4A
4 input HDMI Swamess Switcher with Real-time Multi-view Modes
Front Panel, RS-232, and IR Control
SPDIF Audio Output
Free Windows GUI
USER MANUAL
December 13, 2023
Hall Technologies • 1234 Lakeshore Dr Suite #150 Coppell, TX 75019 •
halltechav.com
Important Safety Instructions
| 1. Do not expose this apparatus to
rain, moisture, dripping or splashing and that no objects filled with liquids,
such as vases, shall be placed on the apparatus.
---|---
2. Do not install or place this unit in a bookcase, built-in cabinet or in
another confined space. Ensure the unit is well ventilated.
3. To prevent risk of electric shock or fire hazard due to overheating, do
not obstruct the unit’s ventilation openings with newspapers, tablecloths,
curtains, and similar items.
4. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
| 5. Do not place sources of naked flames, such as lighted candles, on the
unit.
---|---
6. Clean this apparatus only with dry cloth.
7. Unplug this apparatus during lightning storms or when unused for long
periods of time.
8. Protect the power cord from being walked on or pinched particularly at
plugs.
9. Only use attachments / accessories specified by the manufacturer.
Introduction
OVERVIEW
The SSW-HD-4 is a 4×1 HDMI seamless video switch with multi-view capabilities
where all inputs can be shown in real-time (60 frames per second) on the
output in a variety of modes. When only one input is shown, switching between
different inputs is completely seamless (with zero delay transition). The
switcher supports Input and Output resolutions up to 1080p Full HD.
The SSW can display four Hi-definition sources on a single display and comes
with pre-configured multi-view layouts (4 equal images as shown here, or one
large and 3 smaller windows in various positions). Individual buttons for each
input allow quick selection from the front panel. Control of switching and
multi-view window layouts can be accessed via Front panel, IR remote control
(included), RS-232, or a PC GUI (that controls the device via RS- 232).
The product is shipped with rack ears for 1U rack mounting.
Features
- Seamless Switching
- Pre-configured Multi-view Layouts
- Control via Front Panel, IR, PC-GUI and RS-232
- Input and Output Resolutions up to 1080p Full HD
- HDCP Compliant
- Includes IR Remote Control
- Includes Rack Mount Ears
- De-embedded S/PDIF audio out with RCA Connector
- Supports Locking HDMI Cables
- Includes Universal Power Supply w/ Locking DC Connector
Package Contents
1x SSW-HD-4 Seamless Switcher
1x Locking 12V DC Universal Power Supply Qty (1) IR Remote Control
1x DB9 male-to-female RS232 cable
1x Rack mount ears
Product Description
SSW-HD-4
| No. | Name | Description |
|---|---|---|
| 1 | Power | The green LED lights when SSW is powered. |
| 2 | IR | The IR detector receives signal from the included IR Hand held remote |
controller.
3| Input Buttons| Use this buttons to switch HDMI Inputs seamlessly. The
active Input will be indicated with a back light RED LED.
4| Output Mode| Use this button to change the Multiview Layouts.
By default, the SSW comes has 3 pre- defined layouts. Refer Multiview layouts
for more information.
Hold this button for 7 seconds to enable “Auto Scan” feature.
5| Output Resolution| Use this button to change the Output
resolution to [780p 1080i 1024×768 1360×768 1080p] @60HZ.
Hold this button to factory default the unit.
6| HDMI Inputs| Connect the HDMI video sources using HDMI cables. Use HR HDMI
Locking cable for secure locking.
7| HDMI Outputs| Connect the HD Display using HDMI cable.
8| Audio Output| Use RCA connector to connect to audio devices.
9| RS-232| Connect the RS-232 port to the PC using RS-232 cable.
10| Power Supply| Plug the 12VDC power supply and connect the adapter to the
AC Wall Outlet.
IR Remote Controller
1| Input| Use these buttons to select the Input.
Use these buttons to quickly switch the inputs
---|---|---
2| Mode| Use these buttons to change the Multiview layout.
3| Resolution| Use these buttons to change the resolution of the output video.
Supported Resolutions: 780p, 1080i, 1024×768, 1360×768, 1080p @ 60Hz.
4| Picture| Use these buttons to change the Contrast, Brightness,
Color and Sharpness properties of the Output video. Note that the changes will
affect all the four Inputs simultaneously.
Use this buttons to change the Picture parameters.
If the SSW-HD-4 needs to be installed in a standard 19” rack, you can use the
included rack ears. Multi View Layouts
SSW supports three different Multiview modes. The Output modes can be
configured using Front panel, IR Remote Controller PC-GUI and RS-232. When an
input is selected in Multiview mode it is considered as a primary input and
the other inputs dynamically arrange themselves in the layout as shown below.
Note that Auto Scan can be enabled in Multiview mode. 
Auto Scan (Auto Switch)
The Auto Scan feature is another important feature of the seamless switcher.
When the Auto Scan feature is enabled, the SSW automatically switches to the
latest input plugged. So even if currently selected input has video and you
plug in a new input, it will switch to the new input.
In this mode, when the selected input is unplugged, the SSW automatically
switches to another input with active video (scans from input 4 to input 1).
To enable Auto Scan, hold Output Mode button for 7 Seconds or until the button
light starts blinking. Auto Scan mode is disabled as soon as you switch the
input manually. However, it remains active when changing the Output Mode or
Output Resolution. Note that you can lock the front panel buttons using RS-232
commands.
Locking
The Locking feature provides two modes to disable the front panel buttons
partially or fully. The locking modes can be accessed using RS-232 or PC-GUI.
Factory Default
Factory default applies default setting to the unit. Factory default can be
done from Front panel, RS232 and PC-GUI. To do the Factory default from the
front panel hold the Output Resolution button for 7 seconds or hold until you
see all the inputs buttons blink once.
PC-GUI
The SSW-HD-4 can be controlled using a free PC GUI. The PC-GUI uses the RS-
232 port on the device. Windows® GUI is available on the product’s webpage.
Installation
- Connect up to four HDMI Sources to the HDMI Input ports of SSW.
- Connect an HD display to the HDMI Output port of SSW.
- Optional: Connect an RS-232 Cable from the RS-232 port of SSW to the RS-232 connector of any RS-232 controller (PC).
- Optional: Connect compatible audio devices using RCA cable to the SPDIF port.
- Connect the included 12V DC Locking Power supply. Do not over tighten the locking power connector.
- Connect the power supply to an available electrical outlet.
RS-232
The Serial port on the SSW is always active. When the changes are made from
the front panel or using IR controller the corresponding Serial commands are
sent over RS-232 as a response. This allows easy integration of SSW-HD-4 with
3rd party controllers.
| Description | Setting |
|---|---|
| Baud Rate | 19200 |
| Data bits | 8 |
| Parity | None |
| Stop bits | 1 |
| Flow control | None |
Serial Commands
Note that all the commands should be in upper case and should end with
Carriage Return
| Command | Description | Response |
|---|
S SOURCE n n = 0 to 4
Note:
S SOURCE 0
E.g. S SOURCE 1| Selects the Primary HDMI Input.
Blanks the Output .
Selects the HDMI Input #1. (Default)| -No Response-
RSOURCE| Read the status of primary HDMI| SOURCE n
S OUTPUT n
E.g. S OUTPUT 1| Set the Output resolution. n = 1 — (1080p) (
Default) n = 2 –(720p) n = 3 –(1080I) n = 4
–(1024×768)
n = 5 — (1360×768)
Set the Output resolution to 1080p| -No Response-
R OUTPUT| Read the status of the Output resolution| OUTPUT 1
S MODE n
n = 1 to 4
E.g. S MODE 2| Set the Multiview mode. n = 1 — Mode 1
(Default) n = 2 — Mode 2 n = 3 — Mode 3 n
= 4 — Mode 4
Set Multiview Mode #2| -No Response-
R MODE| Read the status of the Multiview mode| MODE 2
S TILE n n=1 to 4| Set the position of the Input in multi view
mode.| S TILE n
R TILE| Read the status of the Tile.| TILE n
S KEYLOCK n n = 0 to 2| Set the lock for the front panel.
n= 0 — Turn off the Lock. ( Default ) n= 1 — Lock the Resolution. n= 2 —
Lock the Front Panel. Note: The Keylock feature only disables the front
panel, and does not apply to IR Remote.| S KEYLOCK n
R KEYLOCK| Read the status of the key lock.| KEYLOCK n
S OSD n n=0 to 2| Set the OSD mode.
n=0 –OSD OFF ( Default ) n=1 –Display OSD for 3 Seconds n=2 –Always ON|
S OSD n
R OSD| Read the status of the OSD.| OSD n
S CONTRAST n n=0 to 100| Set the Contrast. n=50 ( Default )|
S CONTRAST n
---|---|---
R CONTRAST| Read the status of the contrast.| CONTRAST n
S BRIGHTNESS n n=0 to 100| Set the Brightness. n=50 ( Default )|
S BRIGHTNESS n
R BRIGHTNESS| Read the status of the brightness.| BRIGHTNESS n
S SATURATION n n=0 to 100| Set the Saturation. n=50 (
Default )| S SATURATION n
R SATURATION| Read the status of the saturation.| SATURATION n
S SHARPNESS n n=0 to 100| Set the Sharpness. n=50 ( Default )|
S SHARPNESS n
R SHARPNESS| Read the Sharpness.| SHARPNESS n
S AUTOSCAN n n=0 to 1| Set the Auto scan. n=0 — Disable the auto
scan n=1 — Enable the auto scan See Auto Scan for more information.| S
AUTOSCAN n
R AUTOSCAN| Read the status of the Auto Scan.| AUTOSCAN n
S BORDER n n= 0 to 1| Enable or Disable the border n=0 — Disable the
border ( Default ) n=1 — Enable the border.| S BORDER n
R BORDER| Read the status of the border.| BORDER n
S RESET 1| Reset the unit to factory default.| S RESET 1
Troubleshooting
There are no field serviceable parts or circuits in the device. Opening the
unit will void the warranty.
Contacting Hall Technologies
If you determine that the SSW-HD-4 is malfunctioning, do not attempt to repair
the unit instead, contact Hall Technologies Technical Support at
714-641-6607 or
support@halltechnologies.com.
Before you do, make a record of the history of the problem. We will be able to
provide more efficient and accurate assistance if you have a complete
description.
Shipping and Packaging
If you need to transport or ship your unit:
- Package it carefully. We recommend that you use the original container.
- Before you ship the units back to Hall Research for repair or return, contact us to get a Return Authorization (RMA) number.
Optional Accessories
For controlling the device from a PC you may need a USB to RS-232 adapter
- Compliant with the USB Specifications
- Supports RS-232 serial interface
- Supports up to 15200 kbps data transfer rate
- Supports Plug & Play specification
- USB host device drivers supplied
Specifications
Video
Video Resolution| Output:
1080p@60Hz, 1080i@60Hz, 720p@60Hz, 1024×768@60Hz, 1360×768@60Hz
Input:
480i@60Hz, 480p@60Hz, 576i@50Hz, 576p@50Hz, 720p@50/60Hz,
1080i@50/60Hz, 1080p@24/30/50/60Hz, 800×600@60Hz, 1024×768@60,
1280×720@60Hz, 1920×1080@60Hz
Video Bandwidth| Single-link to 165 MHz (4.95 Gbps)
Audio Standards| PCM [2/5.1/7.1]CH, Dolby Digital 2~5.1CH, DTS 2~5.1CH, Dolby
True HD and DTS-HD Master Audio
Input Ports| 4 x HDMI Female with Locking Capability 1 x RS-232
Output Ports| 1 x HDMI Female with Locking Capability 1x S/PDIF audio out with
RCA Connector
Power Supply| 12 VDC @ 2.5A
Power Consumption| 10W (Max)
ESD Protection| Human Body model: 8kV (air-gap discharge) 4kV (contact
discharge)
Dimensions| 9.85” (250mm) W x 4.65” (118mm) D x 1.25” (32mm) H
Weight| Product: 1.8 lbs (0.8 kg)
Enclosure| Metal
Operating Temperature| Storage: -4 to +140 °F (-20 to +60 °C)
Operating: +32 to +122 °F (0 to +50 °C)
20% to 90% RH non-condensing
© Copyright 2023. Hall Technologies
All rights reserved.
1234 Lakeshore Drive, Coppell, TX 75019
halltechav.com /
support@halltechav.com
+1 (800)-959-6439
Hall Technologies December 13, 2023
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>