KLARSTEIN 10034244 METT MAX Meat Grinder Instruction Manual

METT MAX

10034244
www.klarstein.com

Dear Customer,
Congratulations on purchasing this device. Please read the following instructions carefully and follow them to prevent possible damage. We assume no liability for damage caused by disregard of the instructions and improper use. Scan the QR code to get access to the latest user manual and more product information.

https://use.berlin/10034244

TECHNICAL DATA

SAFETY INSTRUCTIONS

• The device is not intended for commercial use, but only for households and similar environments. This includes kitchens in offices, farms, hotels, motels, and Bed & Breakfasts.
• Disconnect the plug before assembling or disassembling the appliance.
• Only use the appliance under supervision when children are present.
• When moving the unit, hold it by the housing with both hands. Never hold it by the hopper plate or any other part of the unit.
• When using the Kibbeh attachment (for minced meat rolls), do not attach a cutter or perforated discs.
• Do not grind hard food such as bones or nuts in the mincer.
• Do not crush fibrous foods such as ginger in the mincer.
• Do not allow the mincer to run for more than 10 minutes at a time. Let it cool for 10 minutes before using it again.
• Wait 30 seconds after finishing the current process before using the reverse switch. Doing so may damage the unit.
• To avoid blockages, do not press the meat into the funnel under excessive pressure.
• Never attempt to replace or repair permanently installed parts of the appliance yourself.

WARNING
Risk of injury! Never push the meat into the funnel by hand. Always use a food pusher.

BEFORE FIRST USE

• Before use, check the voltage on the device badge. Connect the device only to sockets that correspond to the voltage of the device.
• Wash all accessories with warm water and a little detergent.
• Before plugging the appliance into a wall outlet, make sure that the appliance is switched off.

PRODUCT OVERVIEW

ASSEMBLY AND OPERATION

Hold the head firmly and insert it into the head inlet.| Turn the locker clockwise until the head is firmly seated.
Insert the screw conveyor with its long end pointing forward into the head and turn it slightly until it is firmly seated in the motor housing.| Place the cutting blade on the shaft of the screw conveyor and make sure that the knife is pointing forward. If the knife is not mounted correctly, the meat will not be crushed.
Place the desired cutting plate on the cutting blade and slide the protrusions into the slot.| Press with one finger on the middle of the cutting plate and tighten the fixing ring
with the other hand. Do not overtighten the ring.
Place the hopper plate on the head and fix it into position. Place the unit on a solid worktop. The air outlet on the floor and on the side of the motor housing should be kept free and not blocked.

Mincing meat
WARNING
Risk of injury! Never push the meat into the funnel by hand. Always use a food pusher.
Cut all food into pieces. We recommend that you use tendons, boneless and fat- free meat, and cut it to a size of eta 2x2x6 cm so that it fits easily into the funnel opening.

• Press the ON button.
• Place the pieces of meat on the funnel plate and push them into the funnel with the food pusher (see Fig. 7).
• When you are finished, press the OFF button.

Reverse function
If a blockage occurs, press and hold the REVERSE button for 3-6 seconds. Then release the button. Unplug the appliance and remove the food from the head of the appliance.

Making Kibbeh (minced meat rolls)

Ingredients

Stuffing:| For the rolls:
Mutton 100 g Olive oil 1 1/2 tbsp Onion 1 1/2 tbsp flour 1 1/2 tbsp Spices to taste Salt to taste| Lean meat 450 g Flour 150-200 g Spices to taste Nutmeg 1 tsp Paprika to taste Pepper to taste
Chop the meat three times for the filling and three times for the rolls and mix the minced meat with the remaining ingredients in a bowl.

Before attaching the Kibbeh attachments, remove the perforated disc and the cutting blade.| Screwcap into place until tight. Do not overtighten.
| Place the food container under the outlet. Place the minced meat mixture for the rolls in the funnel and make minced meat rolls.

Fill the finished minced meat rolls with the minced meat filling as shown below and fry or deep-fry them.

Making sausages
Place the cutting knife, one of the perforated discs (fine, medium, coarse), and the corresponding funnel (fine, medium, coarse) on the screw shaft and screw the fastening ring tight.

Thread the sausage skin onto the sausage filling tube and knot the end. Make sure that the sausage casing is loosely filled, as the sausage expands during frying or cooking and the casing can tear open. Press the sausage together at the end with your fingers and turn it once or twice around its own axis.

DISASSEMBLY

• Make sure that the engine is completely stopped.
• Disconnect the plug from the socket.
• Disassemble the parts by performing steps 1-6 in reverse order (see below).

Note: It is easier to remove the perforated disc by inserting a screwdriver between the cutting blade and the perforated disc to loosen it.

CLEANING AND CARE

• Switch off the device and unplug the plug from the socket.
• Allow the appliance to cool down completely.
• Clean the housing with a damp cloth using a mild detergent. Never clean the housing under running water and never put it in water.
• Do not clean the unit with caustic or abrasive cleaning agents.
• The attachments are not dishwasher safe. These parts should only be cleaned in warm water with a small amount of detergent.
• When you have finished cleaning, attach the cable to the cable holder on the bac and store the unit in a dry, clean place where children have no access.

DISPOSAL CONSIDERATIONS

If there is a legal regulation for the disposal of electrical and electronic devices in your country, this symbol on the product or on the packaging indicates that this product must not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of it in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of this product, please contact your local authority or your household waste disposal service.

MANUFACTURER & IMPORTER

Manufacturer:
Chal-Tec GmbH, Wallstrasse 16, 10179 Berlin, Germany.
Importer for Great Britain:
Chal-Tec UK limited
Unit 6 Riverside Business Centre
Brighton Road
Shoreham-by-Sea
BN43 6RE
United Kingdom

References

• Klarstein | Your home. Your kitchen. Your style.
• Take-e-way GmbH | take-e-back | Elektroschrott Rücknahmesystem Onlinehandel

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>