KLARSTEIN 10034711 Gas Griller Instruction Manual
- June 5, 2024
- Klarstein
Table of Contents
KLARSTEIN 10034711 Gas GrillerSAFETY INSTRUCTIONS
- Read the operating instructions before using the appliance and observe the operating and installation instructions.
- Retain this manual for future reference.
- Use outdoors only.
- Accessible parts may be very hot. Never leave children, elderly infirm persons or pets near the barbecue.
- Children must not use the appliance! Persons with reduced physical, sensory or mental capabilities or those with a lack of experience and knowledge may only use the device if they are instructed on how to do so by a person responsible for their safety, or if they are supervised and understand the hazards associated with the use of the device.
- Do not move the appliance during use.
- Turn off the gas supply at the gas cylinder after use.
- Do not modify the appliance.
- This appliance must be kept away from flammable materials during use.
- The regulator and hose must be connected correctly to the appliance. A spanner must be used to tighten the nut onto the connection thread.
- Do not keep any gas cylinder inside the barbecue trolley when using the appliance. It is forbidden to insert/put gas cylinders into the appliance when in use.
Gas Requirements
- For details on the more exact use of your gas bottles, contact your local gas bottle dealer.
- Never use a gas bottle with a damaged container, valve, base or ring.
- A deformed or rusty gas bottle can be dangerous and should be checked for functionality by your local gas bottle dealer before use.
- Never connect the device to an uncontrollable gas source. Turn off the gas when the device is not in use.
- The device may only be operated with propane gas or butane gas or a gas mixture of both types of gas. The gas bottle must not fall down or be handled roughly. The connection to the gas bottle must be disconnected when the grill is not in use. After disconnecting, replace the cap on the gas bottle.
- Before connecting the gas bottle to the grill, make sure the gas tap is turned off, there are no open flames near the unit, and the gasket is in good condition. Then connect the pressure regulator to the gas bottle.
- The connection hose must be replaced every two years.
- Check the connection hose once a month and every time the gas bottle is changed. If the connection hose shows cracks or other signs of deterioration, it should be replaced with a new one.
- Be careful not to kink or twist the connection hose and ensure that it does not touch the hot surface of the equipment.
- Before replacing the gas bottle, make sure that the gas has been shut off and there are no open flames or other sources of heat near the unit. Make sure that the gas bottle is permanently in an upright position.
- Only use the connections and accessories of the device for their intended uses.
- Do not turn the gas bottle upside down to use the remaining gas.
- If local regulations require it, the flexible hose must be replaced.
PRODUCT OVERVIEW
Single parts
ASSEMBLY
GETTING STARTED
Preparation
Note: You will need a gas cylinder and proper regulators under the gas pressure to operate this gas grill. The regulators should be comply with EN16129 with current version and national regulation.
INSTALLATION
- After purchasing your gas cylinder you will then be ready to set it up with your gas grill.
- Check all the parts, and make sure no part is missing. If there are any parts missing, please contact customer service.
- For assembly, you will need a suitable screwdriver and spanner.
- Only use tools that are intact and suitable for the job at hand.
- Select a suitable place to set up the appliance. The appliance is positioned firmly on a flat, sufficiently large surface area. Make sure the inlet and the outlet regulator are correct and suitable for the cylinder valve and appliance.
- If the regulator is used outdoors, make sure that it is protected from atmospheric agents.
- For connecting the gas cylinder, you will need a suitable spanner.
- When connecting the flexible tube, make sure it is not twisted.
How to connect a gas cylinder
- When changing the gas cylinder which shall be carried out away from any source of ignition. Position the gas cylinder at left side of your gas grill, should not be placed inside BBQ, keeping in mind that the gas cylinder must be kept away from heat and in a safe position.
- When ready to use your gas grill insert the regulator into the gas cylinder valve and tighten firmly.
OPERATION
Energy-saving tips
- Reduce the opening time of the lid.
- Turn the grill off as soon as cooking is completed.
- Preheat the gas grill for 10 to 15 minutes only. (Except for the first use)
- Do not preheat longer then recommended.
- Do not use a higher setting than required.
- Connect the hose and regulator to the gas cylinder at the left side of the gas grill keeping in mind that the gas cylinder must be kept away from heat and in a safe position .The hose dimension is 8-10 mm diameter. The length of hose recommended which shall not exceed 1.5 m.
Note: The lid must be open when lighting the burner! Do not stand with your face directly over the gas grill when lighting it.
Lighting the grill
The burner has the following ignition procedure
- Ignition with control gas control (main burner or main burner with side burner or main burner with side burner and side burner).
- When all the switches on the gas grill are in the „Off“ position, turn the gas cylinder valve to the „On“ position.
- To generate a spark, press and hold the throttle control knob (A) for 3-5 seconds to allow the gas to flow, then turn counterclockwise to „HIGH“ (B).
- The spark can then pass to the burner tube (C). You will hear a „snap“ noise from the igniter and you will see an orange flame coming out of the burner tube on the left side of the burner (D).
- After the „snap“ sound, keep the gas regulator pressed for two seconds so that the gas can flow completely through the burner tube (E) and ignition is guaranteed.
- If the burner is ignited, adjacent burners will also be ignited when the grill switch is set to „HIGH“.
- When set to „HIGH“, the burner flame should be approximately 12 – 20 mm long and the orange flame portion should be minimal.
- Turn the throttle control knob fully counterclockwise for the minimum setting.
- If you have difficulty igniting the grill while following the above steps, contact Customer Service or your local gas dealer.
- If automatic ignition cannot be used, remove the grill grille and heat distributor (heating plate) and turn the switch counterclockwise to 90° to ignite the appliance with a grill lighter placed 5 mm from the burner hole.
- Then insert the heat distributor and grill grille back into the grill with protective gloves and wear fire and heat resistant gloves.
Note: If the burner still does not ignite, turn the gas control knob to
the „Off“ position and wait two minutes for the excess gas to evaporate before
attempting to ignite the grill again.
CLEANING AND MAINTENANCE
WARNING
Risk of injury! All cleaning and maintenance should be carried out when the
barbecue is cool and with the fuel supply turned OFF at the gas cylinder.
Outside surface
Use a mild detergent or baking soda and hot water solution. Non-abrasive scouring powder can be used on stubborn stains, then rinse with water.
Barbecue lid
If the inside surface of the barbecue lid has the appearance of pealing paint, baked on grease build-up has turned to carbon and is fl aking off. Clean thoroughly with strong hot soapy water solution. Rinse with water and allow to completely dry. Never use oven cleaner!
Interior of barbecue bottom
Remove residue using brush, scraper and/or cleaning pad then wash with a soapy water solution. Rinse with water and allow to dry.
Wooden surfaces
Wash with a soft cloth and hot soapy water solution. Rinse with water. Do not use abrasive cleaners, degreasers or a concentrated barbecue cleaner on wooden parts.
Cooking grid
Use a mild soapy water solution. Non-abrasive scouring power can be used on stubborn stains then rinse with water.
Cleaning the burner assembly
- Turn the gas OFF at the control knob and disconnect the cylinder.
- Remove cooking grill and cooking plate.
- Clean the burner with a soft brush or blow clean with compressed air and wipe with a cloth.
- Clean any clogged ports with a pipe cleaner or stiff wire (such as an opened paper clip).
- Inspect burner for any damage (cracks or holes). If damage is found, replace with a new burner. Reinstall the burner, check to ensure that the Gas valve orifices are correctly positioned and secured inside the burner inlet (venturi).
Maintenance
Have your gas barbecue serviced once a year by a qualified technician?
TROUBLESHOOTING
| Problem | Possible Cause | Solution |
|---|
Burners will not light using the ignition system.
| LP gas cylinder is empty.| Replace with full cylinder.
Faulty regulator.
| Have regulator checked or replace.
Obstructions in burner.| Clean burner.
Obstructions in gas jets or gas hose.| Clean jets and gas hose.
Electrode wire loose or disconnected on electrode or ignition unit.| Reconnect
wire.
Electrode or wire damaged. Faulty push button igniter.| Replace electrode or
wire. Replace igniter.
Burner will not light with a match.
| LP gas cylinder is empty.| Replace with full cylinder.
Faulty regulator.
| Have regulator checked or replace.
Obstructions in burner.| Clean burner.
Obstructions in gas jets or gas hose.| Clean jets and gas hose.
Low flame or flashback (fire in burner tube –
a hissing or roaring noise may be heard).
| LP gas cylinder too small.| Use larger cylinder.
Obstructions in burner.| Clean burner.
Obstructions in gas jets or gas hose.| Clean jets and gas hose.
Windy conditions.
| Use grill in a more sheltered position.
DISPOSAL CONSIDERATIONS
If there is a legal regulation for the disposal of electrical
and electronic devices in your country, this symbol on the product or on the
packaging indicates that this product must not be disposed of with household
waste. Instead, it must be taken to a collection point for the recycling of
electrical and electronic equipment. By disposing of it in accordance with the
rules, you are protecting the environment and the health of your fellow human
beings from negative consequences. For information about the recycling and
disposal of this product, please contact your local authority or your
household waste disposal service.
MANUFACTURER & IMPORTER (UK)
Manufacturer
Chal-Tec GmbH, Wallstrasse 16, 10179 Berlin, Germany.
Importer for Great Britain
Chal-Tec UK Limited Unit 6 Riverside Business Centre Brighton RoadShoreham-by-
SeaBN43 6RE
United Kingdom
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>