KLARSTEIN 10038393 Espresso Maker Instruction Manual

: June 5, 2024
: Klarstein

Table of Contents

KLARSTEIN 10038393 Espresso MakerSAFETY INSTRUCTIONS
DEVICE OVERVIEW
CONTROL PANEL
OPERATION
Additional function – memory function
CLEANING AND MAINTENANCE
TROUBLESHOOTING
DISPOSAL CONSIDERATIONS
MANUFACTURER & IMPORTER (UK)
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

KLARSTEIN 10038393 Espresso MakerSAFETY INSTRUCTIONS

Read this booklet thoroughly before using the device to protect against damage to the device, fire, electric shock, and injury to persons or property.
Save this manual for future reference.
This device is intended to prepare coffee using high pressure (“Espresso”) and to be used in indoor households, only.
Do not use the device for purposes other than its intended use.
This device may be only used by children 8 years old or older and persons with limited physical, sensory, and mental capabilities and/or lack of experience
and knowledge provided that they have been instructed in the use of the device by a responsible person who understands the associated risks.
Refer all servicing to qualified personnel. Servicing is required when the appliance has been damaged in any way, such as when the power supply cord or plug is damaged, liquid has been spilled over the appliance or objects have fallen into the appliance, or when it has been exposed to rain or humidity, when it does not operate normally, or has been dropped.
Please, only use accessories recommended by the manufacturer of this device to prevent the danger of physical damage, fire or electrical shock to the device or injury to persons.
Make sure that the water tank of the device is always filled with the amount of water needed for the intended operation to prevent damage to the device.
Stay away from hot steam escaping from the unit. Only use the handles or levers attached to the unit or its components if you want to move hot components of the unit, such as the frother or the coffee filter.
Do not immerse the device into water or other liquids to avoid shock damage to the device and harm to you.
Do not touch the plug of the device with wet hands. Water drops from your hands may drip on the plug and cause an electrical shock when in contact with the power socket.
monitor the device during operation, since it needs a manual operation.
Store the device in a dry, clean place out of the reach of unauthorized persons.
Monitor children while they play near the device to protect them from damage.
Unplug the unit when not in use.

CAUTION
Risk of injury! To avoid the risk of burns from hot surfaces and scalding by hot liquid leave the device to cool off completely before taking of or attaching components to it, before cleaning or moving the device or its components.

DEVICE OVERVIEW

CONTROL PANEL

A| Froth button| C| One cup
B| Two cups| D| On / off button

OPERATION

First use/preparation of the still-cold coffee machine

Fill the water tank with water, making sure that the water does not exceed the maximum mark in the water tank.
Remove the funnel from the packaging, insert it into the filter and attach both to the appropriate place in the device. The handle of the funnel must beLOCK.
Plug the power plug into the mains socket. Then press the button . . The device will beep. The indicator lights will start flashing and the unit will warm up. Make sure that the steam knob is in the position. When the steam knob is in the position, all four indicator lights will flash at once and the device will not work.
When the indicator lights light up steadily, press the button to rinse the coffee filter or coffee cup with hot water.

Brew an espresso

While the device is preheating, the coffee powder (the coffee powder should be size 1 powder, not too coarse and not too fine) can be filled into the coffee filter and then compressed with the powder press. In the meantime, remove the coffee powder from the edges of the funnel by hand or with a brush (if one cup is needed, use the filter for one cup; if two cups are needed, use the filter for 2 cups).
Attach the funnel and fix it in the direction of the arrow. Then place the coffee cup under the filter
When the indicator lights and are steadily lit, press the button once and the coffee for a cup of coffee will start to flow out. If you want to make two cups of coffee, press the key. Align the coffee cups so that the coffee flows directly along the inner rim of the cup into the coffee cup.
Wait until the coffee has flowed in completely. Then the coffee is ready.

Milk foam function

First press the button and then the button. At this time, the indicator light will start flashing. As soon as the indicator light is permanently on, the preheating process is finished.
Fill 1/3 of the milk jug with chilled whole milk. Dip the steam nozzle 1 cm deep into the milk surface and then slowly open the steam knob until steam emerges from the front of the nozzle. Note: Release some water from the steam pipe first before foaming milk.
When the milk temperature reaches approximately 75 °C and the milk foam starts to rise, you can move the steam knob to the position and press button to stop the function.

Hot water function
Press the button and turn the steam knob to the position. Hot water will then continuously emerge from the steam line. Turn the steam knob to the position to end the function.

Additional function – memory function

After the unit has heated up (once the indicator lights and are steadily lit), press and hold the button. Coffee then flows out of the funnel. Release the button as soon as the desired amount of coffee is reached. The device will emit a sound, which means that the length of time you pressed the button has been saved. The next time you press the button, the previously stored amount of coffee will come out (the longest time is 60 seconds. If the button was previously pressed for more than 60 seconds, this is invalid and the factory-set time will remain set)Note: If the time period in which you pressed the button was too short, this time will not be saved. The continuous flow volume should be more than 15 ml.
The reminder function for the key works in the same way as described in point 1.
To reset to factory settings, press and hold the buttons simultaneously for 3 seconds. If the device then beeps once, this means that the device has been reset to factory settings.

Cooling function
If you have previously used the steam function, the indicator lights for ‚one cup‘ and ‚two cups‘ will flash quickly because the temperature of the appliance is too high. Turn the steam knob to the position. The device will start pumping water through the pipe. Water will continuously flow out of the steam line and the device will cool down. When the indicator lights stop flashing rapidly, the steam knob can be turned to the position and the cooling process is complete. As soon as the indicator lights for ‚one cup‘ and ‚two cups‘ are continuously lit again, the device can again make coffee.

Decalcification
After you have used the coffee or steam function about 500 times, the device must be decalcified manually. Proceed as follows:

Add some descaler to the water tank (approximately 10 g) and then fill the water tank with fresh water up to the maximum mark.
After you have switched on the appliance and the preheating process is complete, turn the steam knob to the position. The water is now pumped through the pipe.
During descaling, occasionally turn the steam knob to the , position to allow a small amount of descaler to flow out of the funnel outlet.
After about 2 minutes, the device will stop operating.
Now turn the steam knob to the position and then back to the position. The device will again start pumping water through the pipe. Repeat this step approximately 5 times until the water tank is completely empty.
Fill the water tank with fresh water up to the maximum mark and switch the steam knob to the position and then back to the position periodically until the pumping process is complete.

CLEANING AND MAINTENANCE

Cleaning the milk tank and the milk foam tube
Even though you can store the milk tank with milk residues in the fridge, it is important to clean the tank and the milk foam tube regularly to avoid blockages and residues. To clean the milk tank, proceed as follows:

Remove the milk tank from the appliance
Remove the cover of the tank.
Pour out the remaining milk. Thoroughly wash the milk tank and its lid with warm soapy water. Rinse the parts with clear water and dry them well. Do not use abrasive cleaners and scouring sponges, as these will scratch the surface.
Place a large empty cup under the milk foam tube.
Press the [CLEAN] button. The machine starts to release steam through the milk foam hose. Let the machine run for a few seconds until you see no more milk in the cup. When you are finished, press the [CLEAN] button again to stop the process.
Remove any water residue on the milk tank, and then reinsert it into the machine.

TROUBLESHOOTING

Problem	Possible cause	Approach
No coffee comes out of the sieve.	No water in the water tank.	Add water to

the water tank.
The coffee has been

ground too finely.

| Grind the coffee coarsely.
Too much coffee in the sieve.| Fill the sieve with less coffee.
The machine has not been switched on or connected.| Insert the plug into the socket and switch the machine on.
The coffee powder has been stamped/pressed too much.| Refill the machine with coffee and do not pound it too hard.
Liquid runs out of the top of the attached sieve holder.| The sieve holder has not

been locked properly.

| Turn the sieve holder until it

is in the locked position.

Residue on the seal.| Remove the residue.
Too much coffee in the sieve.| Fill the sieve with less coffee.
Milk is not frothy after frothing or does not come out of the milk foam tube.| No more steam.| Fill the water tank with water.
The milk is not cold enough.| Use cold milk.
The milk foam tube is blocked.| Clean the milk foam tube.
The coffee runs through the

sieve too quickly.

| The coffee has been

ground too coarsely.

| Grind the coffee finer.
Not enough coffee in the sieve.| Pour more coffee into the

sieve and gently tamp it.

Problem	Possible cause	Approach
The coffee is too thin.	You have used the small strainer for a double
espresso.	Use the large sieve for

double espresso.

The coffee was ground too

coarsely.

| Grind the coffee finer.
The symbols on the control panel flash alternately.| No water in the water tank.| Add water to the water tank.

DISPOSAL CONSIDERATIONS

If there is a legal regulation for the disposal of electrical
and electronic devices in your country, this symbol on the product or on the packaging indicates that this product must not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of it in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of this product, please contact your local authority or your household waste disposal service.

MANUFACTURER & IMPORTER (UK)

Manufacturer
Chal-Tec GmbH, Wallstrasse 16, 10179 Berlin, Germany.
Importer for Great Britain
Chal-Tec UK limited Unit 6 Riverside Business Centre Brighton Road Shoreham- by-Sea BN43 6RE United Kingdom