KLARSTEIN 10034487 Fireplace Heater Instruction Manual

: June 5, 2024
: Klarstein

KLARSTEIN 10034487 Fireplace Heater

Dear Customer,

Congratulations on purchasing this device. Please read the following instructions carefully and follow them to prevent possible damages. We assume no liability for damage caused by disregard of the instructions and improper use. Scan the QR code to get access to the latest user manual and more product information.

TECHNICAL DATA

Item number	10034486
Power supply	220-240 V ~ 50 Hz
Power	max. 2000 W

SAFETY INSTRUCTIONS

| CAUTION
Risk of burns! Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.
---|---

Do not use the appliance until it is securely fixed as described in this manual.
Check that the voltage indicates on the data plate corresponds with that of the local network before connecting the appliance to the mains power supply.
If the supply cord is damaged, it must be replaced by a qualified engineer in order to avoid a hazard.
The fireplace heater must not be positioned directly under the power socket.
Keep furniture, curtains and other flammable material at least 1 meter away from the appliance.
Do not leave the appliance unattended during use.
Do not leave the appliance unattended whilst connected to the mains supply.
Keep out of reach of children and do not allow them to operate this appliance.
This appliance is intended for household use only and should not be used for industrial purposes.
Do not operate this appliance after a malfunction or after being damaged in any way.
Repairs to electrical appliances should only be performed by a qualified electrician.
Improper repairs may place user at serious risk.
Do not run the mains cable under carpets, rugs, etc.
Do not allow the mains cable to hang over sharp edges or come in contact with hot surfaces.
In order to avoid overheating, do not cover the heater.
Do not use this heater with a programmer, timer, separate remote control system or any other device that switches the heater on automatically, since a fire risk exists if the heater is covered or positioned incorrectly.
Never immerse the product in water or any other liquid for any reasons.
Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
Do not use the appliance outdoors.
Do not use if you have wet hands.
Never use the appliance on or near hot surfaces.
Do not operate with a damaged cord.
Before cleaning the appliance, make sure it is unplugged from the power and that it is completely cooled.
Do not clean the appliance with abrasive chemicals.
Never use accessories that are not recommended or supplied by the manufacturer. It could cause danger to the user or damage to the appliance.
This device may be only used by children 8 years old or older and persons with limited physical, sensory and mental capabilities and / or lack of experience and knowledge, provided that they have been instructed in use of the device by a responsible person who understands the associated risks.
Children should be supervised to ensure that they do not play with the appliance.

PRODUCT DATA SHEET

Model identifier(s):	10034487, 10034488
Item	Symbol
Heat output

heaters only
Nominal heat output| Pnom| 2.0| kW| | manual heat charge control, with integrated thermostat| N/A
Minimum heat output (indicative)| Pmin| 1.0| kW| | manual heat charge control with room and/or outdoor temperature feedback| N/A
Maximum continuous heat output| Pmax,c| 2.0| kW| | electronic heat charge control with room and/or outdoor temperature feedback| N/A
Auxiliary electricity consumption| | fan assisted heat output| N/A
At nominal heat output| elmax| N/A| kW| | Type of heat output/room temperature control
At minimum heat output| elmin| N/A| kW| | single stage heat output and no room temperature control| no
In standby mode| elSB| 0.41| W| | Two or more manual stages, no room temperature control| no
| | with mechanic thermostat room temperature control| no
| with electronic room temperature control| no
| electronic room temperature control plus day timer| no
| electronic room temperature control plus week timer| yes
| Other control options**
| room temperature control, with presence detection| no
| room temperature control, with open window detection| yes
| with distance control option| no
| with adaptive start control| no
| with working time limitation| no
| with black bulb sensor| no
Contact details| Chal-Tec GmbH, Wallstraße 16, 10179, Berlin, Germany

PRODUCT OVERVIEW

Heater
Surround
Log set

PARTS SUPPLIED

ASSEMBLY

| WARNING
Risk of electric shock and other injuries! Only assemble the dos device as described in the operating instructions.
---|---

Required tools:

Pre-drill (2 mm)
Drill bit (8 mm)
Masonry drill
Phillips screwdriver
Drill

Assembly instructions

Before you begin with the assembly, please note the following points:

2 persons are required for assembly.
Keep your back straight when lifting.
Avoid turning your hips. It is better to put your feet back on.
Avoid strong bending of your upper body. Always go to your knees instead of bending your hips. Do not lean in front of or to one side while carrying the fireplace.
Always grasp with the palm of your hand. Do not use your fingertips to hold the fireplace.
Keep the chimney as close to the body as possible to avoid unnecessary and disproportionate strain on the body.
Use gloves for extra support.
Ask for help if needed.

Unpacking the contents

The device is delivered in a single carton. When carefully removing the unit, observe the following instructions:

Make sure that the device is in the correct position, as it is mounted on the
is printed on the carton.
Remove the tapes cuffs.
Carefully lift the chimney out of the carton.
Remove the transport protection and the foils from the fireplace.

Installation

This product is intended for flat wall mounting. Before mounting, make sure that the floor and wall are flat and that the frame is flush.

Mark the position of the holes for the supplied wall brackets on the back of the fireplace with a pencil.
Drill small holes with a small drill (2 mm) to prevent the MDF board from splitting when the screws are inserted.
Attach the two wall brackets to the rear of the fireplace. Use the two small screws supplied.
Place the fireplace against the wall and mark the position of the wall brackets with a pencil. Then set the fireplace aside.
Drill the holes with a 6 mm drill bit and insert the dowels.
Put the fireplace back against the wall and fix it with the supplied long screws.

OPERATION

Control panel and key functions

| **** Press this button to turn the unit on and off.
| Press repeatedly to adjust the flame brightness between 5 (high) and 1 (low). Press and hold the button for 5 seconds, then press repeatedly to switch between flame colors (C1 – C7).
| Press this button to switch between the different heating levels. The selected level will be displayed on the heat level indicator. When the lower bar is illuminated, the fire runs at low power (1000 W), when both bars are illuminated, the fire runs at high power (2000 W).
Press and hold the button for 5 seconds, then press it repeatedly to set the desired temperature from 1-35°C. The temperature will be set to 1-35°C.
| An off timer can be set by repeatedly pressing the timer button while the unit is running. The timer can be set from 0-9 hours in 30-minute increments.
A power-on timer can be set by repeatedly pressing the timer button while the unit is in standby mode. The timer can be set from 0-9 hours in 30-minute increments.
Press and hold the button for 5 seconds to turn off the week timer.
| The display shows the room temperature as standard. When you make certain settings, the display also shows the following

the set flame brightness
the set flame colour
the set temperature

Adjustable flame colors

C1

| Red + Warm White + Blue
---|---

C2

| Red + Warm White

C3

| Red + Blue

C4

| Warm white + blue

C5

| Blue

C6

| Red

C7

| Warm white

REMOTE CONTROL BUTTONS

| Power Button| **** Press the button to turn the appliance On and Off.
---|---|---

| Flame Button| Press the button once, then use the arrow buttons to select the flame brightness between: Flame Button 5 (High) and 1 (Low). Press twice, then use the arrow buttons to select the flame colour between: C1 and C7.
| Arrow Buttons| ** Use the button to change the heating setting between Low (1 KW) and High (2 KW). The level selected will be (y) displayed by the heating level indicator on the fire.
| Desired Temperature**| Press the button, then use the arrow buttons to select the desired temperature for the room temperature (Range 18- 35 °C).

| 9 Hour Timer| With the fire running, repeatedly press the button to select the duration of the timer. This can be adjusted between 0 and 9 hours in 30 minute increments.
Once the set time has elapsed, the fire will turn off.
With the fire in standby, repeatedly press the button to select the duration of the timer. This can be adjusted between 0 and 9 hours in 30 minute increments. Once the set time has elapsed, the fire will turn on.
| Clock| Before using the weekly timer, the clock must be set. To do this:
Press the clock button, then use the arrow buttons to select the day.
Press the clock button again, then use the arrow buttons to select the hour value (24 hour format).
Press the clock button again, then use the arrow buttons to select the minute value.
| Open Window Detection| The fire will operate for 30 mins. If after 30 minutes of operation the room temperature is below 5 °C, the heater will assume a window is open. The heating function will be turned off to conserve energy, and the alarm will sound.

| Week Timer Button| Your fireplace includes a 7 day timer, which allows you to set two periods of operation per day. The fire will operate with the previously used settings for the heating level, desired temperature, and flame colour.
To set the timer press the week timer button. The unit will display the day, period, and if you are setting the On or Off time. For each period both the On and Off times must be set.

For each Period:

Set the On hour value using the arrow buttons, press the week timer button to confirm.
Set the On minute value using the arrow buttons, press the week timer button to confirm.
Set the Off hour value using the arrow buttons, press the week timer button to confirm.
Set the Off minute value using the arrow buttons, press the week timer button to confirm.

The fire will then move onto the next period / first period of following day, allowing this to be programmed in the same way. The days and periods can be scrolled through by repeatedly pressing the week timer button.
To clear an operational period set the ON and OFF times to the same value.

Week timer display

SAFETY CUT-OUT

This appliance is fitted with a safety cut-off which will operate if the fire overheats (e.g. due to blocked air vents). For safety reasons, the fire will NOT automatically reset. To reset the appliance, disconnect the appliance from the mains supply for at least 15 minutes. Reconnect to the mains supply and switch on the appliance.

CLEANING AND CARE

Note: Turn off the unit and unplug it from the power outlet. Wait until the unit has completely cooled down before cleaning it.

Use a vacuum cleaner to clean the ventilation slots and grilles.
Remove dust on the outside surfaces with a damp (not wet) cloth.
Do not use strong cleaning agents or abrasives.
Do not spray the device with liquids or immerse it in water or other liquids.
Never open the heater housing.

Storage

Keep the unit in a dust-free place during the low season. Pack it in the original carton. Wind the heater cable cleanly to avoid damaging the cable.

DISPOSAL CONSIDERATIONS

If there is a legal regulation for the disposal of electrical and electronic devices in your country, this symbol on the product or on the packaging indicates that this product must not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of it in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of this product, please contact your local authority or your household waste disposal service.

This product contains batteries. If there is a legal regulation for the disposal of batteries in your country, the batteries must not be disposed of with household waste. Find out about local regulations for disposing of batteries. By disposing of them in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences.