KLARSTEIN 10034253 Oil Radiator Instruction Manual

10034253 Oil Radiator
Instruction Manual

Note: This product is only suitable for well-insulated spaces or occasional use.

Dear Customer,
Congratulations on purchasing this device. Please read the following instructions carefully and follow them to prevent possible damage. We assume no liability for damage caused by disregard of the instructions and improper use. Scan the QR code to get access to the latest user manual and more product information.

https://use.berlin/10035165

TECHNICAL DATA

SAFETY INSTRUCTIONS

• Do not use the appliance until it is securely fixed as described in this manual.

• Check that the voltage indicates on the data plate corresponds with that of the local network before connecting the appliance to the mains power supply.

• If the supply cord is damaged, it must be replaced by a qualified engineer in order to avoid a hazard.

• The fireplace heater must not be positioned directly under the power socket.

• Keep furniture, curtains and other fl ammable material at least 1 meter away from the appliance.

• Do not leave the appliance unattended during use.

• Do not leave the appliance unattended whilst connected to the main supply.

• Keep out of reach of children and do not allow them to operate this appliance.

• This appliance is intended for household use only and should not be used for industrial purposes.

• Do not operate this appliance after a malfunction or after being damaged in any way.

• Repairs to electrical appliances should only be performed by a qualified electrician.

• Improper repairs may place users at serious risk.

• Do not run the mains cable under carpets, rugs, etc.

• Do not allow the mains cable to hang over sharp edges or come in contact with hot surfaces.

• In order to avoid overheating, do not cover the heater.

• Do not use this heater with a programmer, timer, separate remote control system or any other device that switches the heater on automatically, since a fi re risk exists if the heater is covered or positioned incorrectly.

• Never immerse the product in water or any other liquid for any reasons.

• Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.

• Do not use the appliance outdoors.

• Do not use if you have wet hands.

• Never use the appliance on or near hot surfaces.

• Do not operate with a damaged cord.

• Before cleaning the appliance, make sure it is unplugged from the power and that it is completely cooled.

• Do not clean the appliance with abrasive chemicals.

• Never use accessories that are not recommended or supplied by the manufacturer.
  It could cause danger to the user or damage to the appliance.

• This device may be only used by children 8 years old or older and persons with limited physical, sensory and mental capabilities and/or lack of experience and knowledge,  provided that they have been instructed in the use of the device by a responsible person who understands the associated risks.

• Children should be supervised to ensure that they do not play with the appliance.

CAUTION
Risk of burns! Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.

PRODUCT DATA SHEET

only
Nominal heat output| RIOT| 2.0| kW| | manual heat charge control, with integrated thermostat| N/A
Minimum heat out-put (indicative)| Pin| 1.| kW| | manual heat charge control with room and/or outdoor temperature feedback| N/A
Maximum continuous heat output| Box| 2.0| kW| | electronic heat charge control with room and/or outdoor temperature feedback| N/A
Auxiliary electricity consumption| | fan assisted heat output| N/A
At nominal heat output (fan motor)| elmox| 0| kW| | Type of heat output/room temperature control
At minimum heat output (fan motor)| elms| 0| kW| | single-stage heat output and no room temperature control| no
In standby mode| elsB| 0| kW| | Two or more manual stages, no room temperature control| no
| | with mechanic thermostat room temperature control| no
| with electronic room temperature control| no
| electronic room temperature control plus day timer| no
| electronic room temperature control plus week timer| yes
| Other control options (multiple selections possible)
| room temperature control, with presence detection| no
| room temperature control, with open window detection| no
| with distance control option| no
| with adaptive start control| no
| with working time limitation| no
| with black bulb sensor| no
Contact details| Chal-Tec GmbH, WallstraBe 16, 10179, Berlin, Germany

ASSEMBLY

| Place the unit on a scratch-free and stable surface to prevent damage to the paint or your floor surface.
• Turn the unit upside down.
• Pull out the wheels on both sides.
• Operate the unit only in an upright position with the wheels fixed to the floor.
---|---

PRODUCT OVERVIEW AND KEY FUNCTIONS

| A Rear handle and remote control storage  compartment
B Radiator
C Wheel stand
D Front handle
E Control panel
F On/Off switch
G Cable rewind
H Wheels
---|---
| a Thermostat
b Increase time & temperature
c Power/Mode
d Set timer
e Reduce time & temperature
f Standby

Inserting batteries into the remote control

OPERATION

Press the Standby button (f) to turn on the unit. The product is now in standby mode.
You can now select a function from the control panel or remote control. The unit beeps and the power indicator (plug symbol) lights up. A beep sounds each time the button is pressed.

Press the standby key (f) to exit the standby mode and select one of the modes.
Heating starts with low power operation.

Setting the heat output

Press the Power/Mode button (c) repeatedly to select one of the following heat outputs:
Low ( ), Medium ( ), High ( ) and Eco mode (ECO). For low power, medium power and high power, the heater will keep the power constant.

Note: The higher the power, the faster the desired temperature will be reached but the power consumption will increase. We recommend a lower power level if the heater is to  be used for a longer period of time.

Eco-mode
Press the Power/Mode button (c) until the ECO light illuminates. In Eco mode, the heating output adjusts automatically when the room temperature approaches the set temperature.

Example: The set temperature is 25 °C. If the room temperature is lower than 22 °C, the heating operates at high output. If the room temperature rises to 23 °C, the heating operates at the medium output. If the room temperature rises to 24 °C, the heating operates at low output. When the room temperature reaches the set temperature, the heating switches off automatically. As soon as the room temperature drops again, the heating switches on again automatically.

Note: If no temperature is set, the default temperature is 23 °C.

Thermostat setting (Eco model only)

Note: The temperature can be adjusted between 10-30 °C.

1. Press the Power/Mode button (c) until the ECO light illuminates.
2. Press the thermostat button (a), the temperature display will flash.
3. Use the [+] and [-] buttons to set the desired temperature.
4. The temperature display stops flashing and the current room temperature is displayed.
5. The heater maintains the room temperature by switching on and off again and again.

Switching off the unit
Press the standby button (f) until the unit switches to standby mode and the display turns off. Then press the Standby button again to completely turn off the unit and unplug it from the wall outlet.

Timer: Automatic switch-on
Note: This function should only be set if you want the heater to turn on automatically after a specified time (1 to 24 hours from the time of setting). Set the timer in standby mode.

1. Press the Standby button (f) to turn on the unit. The power indicator (plug symbol) lights up. The unit is in standby mode.

2. Press the timer button (d), the light (H) lights up, and the number of starting hours (0.0) flashes.

3. Use the [+] and [-] keys to set the operating time of the heater between 1-24 hours.
   Between 0.0-5.0 hours the time can be set in 0.5-hour increments, between 5-24 hours the time can be set in 1-hour increments. Then wait briefly until the hour digit no longer flashes. The countdown time is now shown on the display.

4. The heater switches on automatically when the time has elapsed.

5. Once you have set the timer, open the Eco mode. Then make the temperature settings in ECO mode so that the heater switches on at the desired temperature or power.

Note: Since the heater may switch on unattended in Timer mode, be sure to follow the safety instructions.

1. Press the timer button (d) while the heater is running, the light (H) lights up and the number of start hours (0.0) flashes.

2. Use the [+] and [-] keys to set the heating operating time between 1-24 hours.
   Between 0.0-5.0 hours the time can be set in 0.5-hour increments, between 5-24 hours the time can be set in 1-hour increments. Then wait briefly until the hour digit no longer flashes. The countdown time is now shown on the display.

3. The heater switches off automatically when the time has elapsed.

CLEANING AND CARE

Note: Turn off the unit and unplug it from the power outlet. Wait until the unit has completely cooled down before cleaning it.

• Use a vacuum cleaner to clean the ventilation slots and grilles.
• Remove dust on the outside surfaces with a damp (not wet) cloth.
• Do not use strong cleaning agents or abrasives.
• Do not spray the device with liquids or immerse it in water or other liquids.
• Never open the heater housing.

DISPOSAL CONSIDERATIONS

If there is a legal regulation for the disposal of electrical and electronic devices in your country, this symbol on the product or on the packaging indicates that this product must
not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of it in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of this product, please contact your local authority or your household waste disposal service.

MANUFACTURER & IMPORTER (UK)

Manufacturer:
Chal-Tec GmbH, Wallstrasse 16, 10179 Berlin, Germany.
Importer for Great Britain:
Chal-Tec UK limited
Unit 6 Riverside Business Centre
Brighton Road
Shoreham-by-Sea
BN43 6RE
United Kingdom

References

• Klarstein | Your home. Your kitchen. Your style.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>