KLARSTEIN 10035321 Midnight Sun Ceiling Heater and Lamp Instruction Manual

KLARSTEIN 10035321 Midnight Sun Ceiling Heater and Lamp SAFETY INSTRUCTIONS

1. Check that the voltage indicates on the data plate corresponds with that of the local network before connecting the appliance to the mains power supply.
2. If the supply cord is damaged, it must be replaced by a qualifi ed engineer in order to avoid a hazard.
3. The heater must not be positioned directly under the power socket.
4. Keep furniture, curtains and other fl ammable material at least 1 meter away from the appliance.
5. Keep out of reach of children and do not allow them to operate this appliance.
6. this is appliance is intended for household use only and should not be used for industrial purposes.
7.  Do not operate this appliance after a malfunction or after being damaged in any way.
8. Repairs to electrical appliances should only be performed by a qualifi ed electrician.
9.  Improper repairs may place user at serious risk.
10.  Do not run the mains cable under carpets, rugs, etc.
11. Do not allow the mains cable to hang over sharp edges or come in contact with hot surfaces.
12. In order to avoid overheating, do not cover the heater.
13. Do not use this heater with a programmer, timer, separate remote control system or any other device that switches the heater on automatically, since a fi re risk exists if the heater is covered or positioned incorrectly.
14. Never immerse the product in water or any other liquid for any reasons.
15. Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
16. Do not use the appliance outdoors.
17. Do not use if you have wet hands.
18. Never use the appliance on or near hot surfaces.
19.  Do not operate with a damaged cord.
20. Before cleaning the appliance, make sure it is unplugged from the power and that it is completely cooled.
21. Do not clean the appliance with abrasive chemicals.
22. Never use accessories that are not recommended or supplied by the manufacturer. It could cause danger to the user or damage to the appliance.
23. This device may be only used by children 8 years old or older and persons with limited physical, sensory and mental capabilities and / or lack of experience and knowledge, provided that they have been instructed in use of the device by a responsible person who understands the associated risks.
24. Children should be supervised to ensure that they do not play with the appliance.

CAUTION
Risk of burns! Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.\

SCOPE OF DELIVERY

1. 1x Heater
2. 1x Socket receiver
3. 1x Remote control
4. 4x Screws
5.  4x Dowels
6.  1x Manual
7. 1x Waterproof insulating tape (30 cm)

DEVICE OVERVIEW

MOUNTING ON THE CEILING

Note: Installation and power connection must be carried out by a qualified electrician!

1.  Mark the mounting holes on the ceiling (where the power cable comes out of the ceiling) and drill into the ceiling at the marked points. Then insert the plugs into the ceiling.
2. Wire the LED light input cable to the power cable in the ceiling and wrap the connection with waterproof insulating tape (supplied) or another suitable insulating tape There are 3 wires inside the LED Light Input Cable (live wire, neutral wire & ground wire). Make sure to connect the appropriate lines (live wire to live wire, neutral wire to neutral wire, ground wire to ground wire). Note: Never hang the heater from the LED power input cable or the heater power cable on the ceiling.
3. Align the mounting holes with the dowels Insert the screws through the mounting holes and tighten them. Finally, place the rubber plugs on the holes.

OPERATION OF THE LED LIGHT STRIP

Once the heater is installed and wired, the LED is controlled by the light switch on the wall. When the LED is switched on, the standard light colour is cool white, when the LED is switched off and on again, the light colour changes to warm white.

Note: The LED lighting can only be used as decoration.

SET DESCRIPTION AND GENERAL FUNCTIONS

Each set consists of two parts:

• A remote control with digital display, which houses the electronics, the controls and the built-in room temperature sensor.
• A socket receiver that can receive and decode the signal from the remote control.

Remote control functions
The remote control uses its integrated sensor to detect the room temperature and sends a signal to the socket receiver to switch the heater on and off when the ambient temperature changes, thus maintaining a constant room temperature.

• If the room temperature is 0.5 °C higher than the target temperature, the remote control sends an OFF command to the receiver. The heater is switched off.
• If the room temperature is 0.5 °C lower than the target temperature, the remote control sends an ON command to the receiver. The heater is switched on. The display of the remote control shows the set temperature, the measured temperature, time, date, modes and various other values. With the remote control you can program the week, set the auto OFF timer and many other functions.Note: The remote control is powered by two 1.5 V AA batteries. Please replace the batteries as soon as the battery symbol flashes, otherwise the remote control will no longer be able to control the heater.The remote control has a lock function (parental lock) which ensures that children cannot change the heater settings.
• When the LCD screen is switched off, only the receiver (heater) is switched off; the remote control itself is still in operating mode until the batteries are empty. The LCD screen of the remote control only works within an ambient temperature of 1-50 °C.

SOCKET RECEIVER

Note: The ON/OFF button on the receiver is intended for pairing mode. To turn the heater on and off, use the ON/OFF button on the remote control.

REMOTE CONTROL

OPERATION IN DETAIL

Commissioning
When you use the heater for the first time, you must first connect the remote control and the socket receiver.

• First plug the socket receiver into the socket.
• Press and hold the ON/OFF button on the socket receiver for 3 seconds.
• Then press the two remote control buttons °C/°F and MODE simultaneously until you hear a beep and both units are connected.

Note: The connection between the two devices should be completed within 3 minutes, otherwise you will need to press the button on the socket receiver again to restart the connection process.

Operating the heater by remote control
Press the ON/OFF button on the remote control to switch the heater on and off. When you turn the heater off, only the heater but not the remote control is turned off, it continues to send signals to the power outlet receiver.

Note: The ON/OFF button on the receiver is for pairing mode. To turn the heater on and off, use the ON/OFF button on the remote control.

Switching the child lock on/off

Press and hold the LOCK button for 3 seconds to turn the button lock on or off. Selecting the display format
Press the °C/°F button to select the desired display format.

Setting the temperature
Press the UP or DOWN button to set the target temperature. If you have set a weekly timer, you can also adjust the temperature manually. However, this will be overwritten with the programmed target temperature when the next heating period starts.
Select heating mode
Press and hold the MODE button for 3 seconds to select SMART mode or TIMER ON/OFF mode. When you turn on the remote control for the first time, the display shows OFF for both modes.

• TIMER ON/OFF means that the programmed timer and temperature settings of 1-5 (Monday-Friday), 6 (Saturday) and 7 (Sunday) are turned ON or OFF. Symbols 1- 5, 6 and 7 are shown at the bottom of the mode display.
• SMART ON means that the remote control calculates the temperature difference between the room and the target temperature 3 hours before the programmed start time and decides by how much earlier the heating must be switched on to reach the target temperature on time.
• The SMART MODE has a monitoring function that detects open windows. If open windows are detected, the heating is automatically switched off or on if the room temperature continuously drops or rises above 1.5 °C within 3 minutes.

SET button

With the SET key you can set the weekly timer and temperature, intelligent adaptive start time and FAV temperature. To do this, press and hold the SET button for 3 seconds.

Note: A completed setting does not automatically start the heating. The heater will not be turned on until the on timer is active.

Setting the weekly timer
First set the time for switching the heating on and off for days 1-5 (Monday- Friday). Press HIGH to set the hour for the timer and DOWN to set the minutes for the timer (15 minutes per press). Then press SET to save the setting and adjust the temperature. When you are finished, press SET to make the settings for 6 (Saturday) and 7 (Sunday) in the same way. Finally, press SET again to save the settings.

Intelligent adaptive start time
If you select the SMART mode with the weekly timer set, the heating is operated independently of the preset timer. The remote control measures the temperature difference between the room and the target temperature 3 hours before the programmed start time and calculates and decides by how much earlier the heating must be switched on to reach the target temperature on time.
Setting the FAV temperature
After the previous setting is connected, you will be taken to the FAV temperature setting. Only the temperature symbol flashes on the display. Now set your favourite temperature and confirm the setting with SET.
If the weekly timer is active, press the FAV button to call up the temperature you have set. However, this will be overwritten with the programmed target temperature when the next heating period starts.
Setting the current date and time
Press and hold the TIME button for 3 seconds, then use the UP and DOWN buttons to set the year/month/weekday and hour/minute. The heater symbol only appears on the display when the heater is running. This is the case when the room temperature is more than 0.5 °C below the target temperature.
Backlighting of the remote control
When you press a button on the remote control, the backlight of the remote control turns on.
Open window detection
The SMART MODE has a monitoring function that detects open windows. If open windows are detected, the heating is automatically switched off or on if the room temperature continuously drops or rises above 1.5 °C within 3 minutes.

IMPORTANT NOTES ON OPERATION

• One remote control can be connected to several receivers at the same time and thus operate several heaters.
• All settings must be reset after changing or removing the batteries. use the weekly timer, make sure that the TIMER function has been switched to ON by pressing the MODE button for a long time. If you prefer to operate the heater manually, make sure that the TIMER function is set to OFF.
• Do not cover or touch the temperature sensor located on the top of the remote control.
• Leave the remote control open in the room, do not put it in a drawer or bag, under a pillow or blanket.
• Replace all batteries with new ones immediately when the battery symbol flashes on the display, otherwise the remote control will not be able to control the heater.
• Remove the batteries from the remote control if you are not going to use it for a long time.
• Please unplug the receiver from the power outlet if it will not be used for a long period of time.

CLEANING AND CARE

Note: Turn off the unit and unplug it from the power outlet. Wait until the unit has completely cooled down before cleaning it.

• Use a vacuum cleaner to clean the ventilation slots and grilles.
• Remove dust on the outside surfaces with a damp (not wet) cloth.
• Do not use strong cleaning agents or abrasives.
• Do not spray the device with liquids or immerse it in water or other liquids.
• Never open the heater housing.

DISPOSAL CONSIDERATIONS

If there is a legal regulation for the disposal of electrical and electronic devices in your country, this symbol on the product or on the packaging indicates that this product must not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of it in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of this product, please contact your local authority or your household waste disposal service. This product contains batteries. If there is a legal regulation for the disposal of batteries in your country, the batteries must not be disposed of with household waste. Find out about local regulations for disposing of batteries. By disposing of them in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences.

MANUFACTURER & IMPORTER (UK)

Manufacturer
Chal-Tec GmbH, Wallstrasse 16, 10179 Berlin, Germany.
Importer for Great Britain Chal-Tec UK limited Unit 6 Riverside Business Centre Brighton Road Shoreham-by-SeaBN43 6RE
United Kingdom

References

• Klarstein | Your home. Your kitchen. Your style.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>