KLARSTEIN 10031372 Ice Cube Maker Instruction Manual

KLARSTEIN 10031372 Ice Cube Maker

Dear Customer,
Congratulations on purchasing this equipment. Please read this manual carefully and take care of the following hints to avoid damages. Any failure caused by ignoring the items and cautions mentioned in the instruction manual is not covered by our warranty and any liability. Scan the QR code to get access to the latest user mannual and other information about the product

TECHNICAL DATA

SAFETY INSTRUCTIONS

• Check that the mains voltage corresponds to the rating of the appliance before operating.
• Use handles or knobs when moving. Place on a flat stable surface for use. Do not use outdoors.
• Do not use near or in the immediate vicinity of a bath or swimming pool or any source of liquid.
• Unplug from socket outlet when not in use.
• To protect against electric shock, do not immerse cord or plug in water or any other liquid.
• The use of accessory attachments not recommended by the appliance manufacturer, may cause injury.
• Do not locate this appliance immediately below a socket outlet.
• Do not allow cord to overhang the counter top where it can be easily pulled by children.
• Do not use this appliance for anything else other than its intended use.
• Do not overfill as this may cause a hazard. Ensure lid is closed when in operation
• To remove plug from outlet, do not pull on supply cord. Grasp plug firmly and pull to remove.
• No liability can be accepted for any damage caused by non compliance with these instructions or any other improper use or mishandling. This appliance is for household use only
• This appliance is not intended to be operated by means of an external timer or separate remote control system.
• This appliance is not intended to be immersed in water.
• If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
• Please according to local regulations regarding disposal of the appliance for its flammable blowing gas.
•  Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
• Fill with potable water only.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

This appliance contains the coolant isobutane (R600a),a natural gas that is environmentally friendly. Although it is flammable, it does not damage the ozone layer and does not increase the greenhouse effect. The use of this coolant has, however,led to a slight increase in the noise level of the appliance. In addition to the noise of the compressor,you might be able to hear the coolant flowing around the system. This is unavoidable and does not have any adverse effect on the performance of the appliance. Care must be taken during the transportation and setting up of the appliance that no parts of the cooling system are damaged. Leaking coolant can damage the eyes.

WARNING
Danger from fire/flammable materials. Please observe the local regulations for the disposal of units with flammable refrigerants and gases.

• Keep ventilation openings in the unit housing free of obstacles.
• Do not damage the refrigerant circuit.
• Do not use any mechanical devices or other means to accelerate the defrosting process or the ice recovery process.
• Do not use other types of electrical appliances inside the ice cube machine.

Special Notes

• When positioning the unit, make sure that the power cord is not pinched or damaged.
• Make sure that there are no multiple sockets or power supplies on the back of the unit.

To avoid contamination of food, please follow the instructions below:

• Regularly clean surfaces that may come into contact with food. Clean the water drain regularly.
• If the appliance contains a water tank, clean it if it has not been used for 48 hours. Rinse the tank if no water has been removed for 5 days.

WARNING
When using, servicing and disposing of the unit, pay attention to the left symbol on the rear of the unit or on the compressor. This symbol warns of possible fi res. There are fl ammable substances in the refrigerant lines and in the compressor. Keep the appliance away from sources of fi re during use, maintenance and disposal.

PRODUCT OVERVIEW

1. Rear Cover
2. Top Cover
3. Water Tray
4. Evaporator
5. Ice Shovel
6. Ice-Bin-Full Sensor
7. Transparent lid
8. Ice Basket
9. Water Reservoir
10. Filter
11. Water Drain Plug
12. Compressor
13. Power Cord
14. Control panel

CONTROL PANEL AND OPERATION

POWER
The indicator of POWER will flash after being plugged in, and then the machine enters the standby state. It will start to work by pressing the POWER button, and accompanying indicator lighting. During operation, pressing this button, the machine will return to the standby state.
SELECT
This button is for selecting the size of ice. The default setting is large ice, if the small one is needed, pressing this button is available. When you select the desired size, the corresponding indicator of S (small) or L (large) will be on. Press and hold the „SELECT“ button for 3 seconds to activate the pipeline self-clean process, which takes „pump water in for 30 seconds—water tank run to drain out water“ as a circle, and this circle will run for 5 times. Flas- hing of indicators of „S“ and „L“ will take place in turn until the self-clean process is over and the machine enters standby mode. Take away the plastic plug to drain water and then the whole process is finished.
ADD WATER
When the indicator of this button turns to red, it means insufficient water to the water reservoir, you need to add enough water and press the POWER button to restart the machine.
ICE FULL
When the ice reach to the max storage capacity, the indicator of this button will flash, and the machine will stop working. What you need to do is pouring out the ice, if the position of ice is lower than the position of ice bin full sensor, the machine will restart automatically.

Operation

1. Plug out, and clean the water reservoir by adding water, then take the plastic plug away to drain out the water from the water reservoir.
2. Reinstall the plastic plug, and add appropriate clean water. After connecting the power supply well, press and hold the „SELECT“ button for 3 seconds to activate pipeline self-clean process. After cleaning, drain out the water by taking the plastic plug away.
3. Open the lid and take out the ice basket to add appropriate water into the water reservoir. Note: The water poured into water reservoir should be lower than the water reservoir’s MAX position. When water volume goes beyond the max, please open the bottom water drain plug to drain the spare water out. Then close the transparent lid.
4. Select the desired ice size, the default size of the machine is large one. Note: Please select the (S) when the ambient temperature is below 15°c.When the ambient temperature is higher than 30°C, Large ice cube sizes are recommended.

Note: For the first three cycles, the ice may be small and irregular in size. Note: When the ice collecting tray is full please remove the ice immediately, Do not allow the ice collecting tray to overfill.

CLEANING AND CARE

• Clean the inner liner, ice collecting tray, water box, ice shovel and evaporator frequently. When cleaning,unplug the unit and remove the ice cubes. Use a diluted solution of water and vinegar to clean the inside and the outside surface of the Icemaker. Do not spray Ice maker with chemicals or diluted agents such as acids, gasoline or oil. Rinse thoroughly before starting.
• Keep ventilation openings in the appliance enclosure, or in the built-in structure, clear of obstruction. Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
• Reuse the machine after being idled for a period of time, it may not have enough water to pump for air retard, and the indicator of “ADD WATER” will keep lighting. At this time, you just need to press the POWER button again, the machine can enter the normal state.
• To ensure the cleanness of ice, please change the water for water reservoir at least once one day. If do not use for a long time, please drain the water out and clean it up.
• If the compressor takes a strike action for shortage water, fully water or interruption of power supply, it will delay for 3mins to start up after restart.
• Always use fresh water before starting ice production either at initial installation or after a long shut-off period.

TROUBLESHOOTING

Please note, if a power failure occurs due to disconnection of the power cord, or the power button has been pushed off during an ice-making cycle, small ice chips may formed and lodge in the automatic shovel causing it to jam. If this occurs, the ice chips may be removed by disconnecting the power cord and gently pushing the shovel to the rear of the cabinet and removing the ice chips, then restarting. Please check if the water reservoir is flat when the ice shovel can not remove the ice to ice basket. If not, please push the ice shovel gently by finger, then press POWER button to restart.

normal.
Water shortage indicator

light is on.

| There is no water.| Add to some water until it

reaches MAX position.

The pump is full of air.| Press POWER button to

restart.

Indicator lights on display

are not on.

| Blown fuse/ No power.| Replace fuse / Turn power

on.

The Ice made is too large and with pieces sticking together.| Water temperature is too

low.

| Select small size.
.Ice of previous cycles left in the water tray.| Take out the ice under the

standby state.

All indicators twinkle

simultaneously.

| Water tray is blocked by

ice cube.

| Unplug the power to take out the ice which blocking the tray, then

plug the power and press the POWER button, the machine will restart 3mins later.

DISPOSAL CONSIDERATIONS

If there is a legal regulation for the disposal of electrical and electronic devices in your country, this symbol on the product or on the packaging indicates that this product must not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of it in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of this product, please contact your local authority or your household waste disposal service.

MANUFACTURER & IMPORTER (UK)

Manufacturer:
Chal-Tec GmbH, Wallstrasse 16, 10179 Berlin, Germany.
Importer for Great Britain:
Chal-Tec UK Limited Unit 6 Riverside Business Centre Brighton Road Shoreham- by-Sea BN43 6RE United Kingdom

References

• Klarstein | Your home. Your kitchen. Your style.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>