cecotec CONGA Rockstar 700 Ultimate Ergowet Electric Broom Vacuum Cleaner User Guide

cecotec CONGA Rockstar 700 Ultimate Ergowet Electric Broom Vacuum Cleaner User Guide

SAFETY INSTRUCTIONS

• Read these instructions thoroughly before using the appliance. Keep this instruction manual for future reference or new users.
• Make sure that the mains voltage matches the voltage stated on the rating label ofthe appliance and that the outlet is grounded. This appliance is intended for domestic use only. It is not suitable for commercial or industrial use.
• Check the power cord regularly for visible damage. If the cord is damaged, it must be replaced by the official Technical Support Service of Cecotec, in order to avoid any type of danger.
• Do not use the device if it has been dropped or if there are any visible signs of damage.
• Do not try to repair the appliance by yourself.
• Contact the official Technical Support Service of Cecotec for advice. Do not use any accessory that has not been recommended by Cecotec, as they might cause injuries or damage.
• Do not place the appliance close to heat sources, flammable substances, wet surfaces where it can fall or be pushed into water or allow it to come into contact with water or other liquids. Do not use it outdoors.
• Do not use the appliance to vacuum liquids, lighted matches, cigarette ends, hot ash or on wet surfaces.
• Do not use on concrete, tarmac or other rough surfaces. Take special care when using the device to clean stairs.
• Do not block the appliance’s openings or hinder air flow. Keep openings free of any objects such as dust, lint, clothing or fingers. Keep hair away from moving parts.
• Turn off and unplug the appliance from the mains supply when it is not going to be used for a long period of time, before cleaning or repairing, before attaching components and before removing the battery.
• Never modify the charger in any way.
• Do not use any battery that has not been provided with the original product or by Cecotec.
• Do not carry the battery by the cord or coil the cord around the battery to store it.
• Always operate and store the devices in places where the room temperature is between 5 and 40 ºC.
• Make sure the high-efficiency filter and the main rolling brush are properly installed before operating the device.
• Pullfrom the plug, not the cord, to disconnect itfrom the outlet. Do not immerse the cord, plug, or any non-removable part of the appliance in water or any other liquid, nor expose the electrical connections to water.
• Make sure your hands are dry before handling the plug or switching on the appliance.
• The appliance is not intended to be used by children under the age of 12.
• It can be used by children over the age of 12, as long as they are given continuous supervision.
• This appliance is not intended to be used by persons with reduced physical, sensory, or mental capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction concerning the use of the appliance in a safe way by a person responsible for their safety, and understand the hazards involved.
• Supervise young children to make sure that they do not play with the appliance. Close supervision is necessary when the appliance is being used by or near children

Battery instructions

• This appliance includes Li-ion batteries, do not incinerate or expose them to high temperatures, as they may explode. Leaks from the battery or battery cells can occur under extreme conditions. Do not touch any liquid that leaks from the battery.
• If the liquid gets into contact with skin, wash immediately with soap and water. If the liquid gets into the eyes, flush them immediately with clean water for a minimum of 10 minutes and seek medical attention. Wear gloves to handle the battery and dispose of immediately in accordance with local regulations. Avoid contact between the battery and small metallic objects such as paper clips, coins, keys, nails or screws.
• Before a new battery is used or the battery is used for the first time after long-term storage, fully charge the battery. When the device is stored and not used for long periods of time, ensure that the battery pack is fully charged, and ensure that the battery is charged and discharged at least once every three months.

PARTS AND COMPONENTS

Fig. 1

1. Suction base release button
2. Vacuuming tube release button
3. Dust tank release button
4. High-efficiency filter
5. Power push button
6. Power button
7. Power supply
8. Battery
9. Power adapter
10. Vacuuming Flex tube
11. Suction base
12. Union elbow
13. Extensible tube
14. Long brush
15. Narrow brush for furniture and corners
16. Wide brush for furniture and corners
17. Motorised upholstery brush
18. Wall bracket
19. Wall plugs
20. Screws
21. Dust tank
22.  Jalisco brush
23.  Silicone and bristles brush
24. Adhesive for wall bracket
25. Water tank for scrubbing

BEFORE USE

Take the product out of the box.
Check for any visible damage, if any is observed, contact as soon as possible the Technical
Support Service of Cecotec for advice or reparation.

PRODUCT ASSEMBLY

Vacuuming tube and suction base assembly
To install the suction base into the vacuuming tube, align both of them making sure the tab on the suction base matches the guides on the tube, and introduce one into the other until they are firmly fixed. To disassemble them, press the suction base release button and pull from the vacuuming tube while you hold the suction base.
**Fig. 2

**

Note: when assembling these 2 parts, make sure the handle and the brush are facing the same direction.
Use the Flex tube to reach and clean the most difficult areas and dirt. To bend the tube, press the Flex button.

Battery and handheld vacuum cleaner assembly
Introduce the battery in the slot located in the handheld vacuum cleaner. Once it is introduced, move it slightly to ensure it is properly assembled in place.
Fig. 3

Following the below illustration, keep the vacuuming tube vertically, align the tab on the vacuuming tube with the guides in the handheld vacuum cleaner and introduce the tube.

Dust tankand handheld vacuum cleaner
To assemble the dust tank to the handheld vacuum cleaner, first separate the handheld vacuum cleaner from the vacuuming tube.
Then, press the vacuuming tube release button with one hand and, holding from the handle with the other one, turn the dust tank anticlockwise to the unlock position indicated on the dust tank edge.
To disassemble the dust tank, turn it clockwise until it reaches the unlock position.
**Fig. 4

**

Suction base, vacuuming tube and handheld vacuum cleaner installation
To complete the full installation of the device, hold the vacuuming tube with the suction base assembled upright and introduce the tube in the handheld vacuum cleaner as shown on the illustration.
**Fig. 5

**

OPERATION

• Handheld vacuum cleaner
• Once the handheld vacuum cleaner has been disassembled from the vacuuming:
• Press the On/off button to turn the device on.
• Press the power push button to select the desired power level.
• It will automatically operate in Eco mode. The power level can be adjusted at any moment by pressing this button.
• Press once to switch to Daily mode.
• Press again to operate it at Turbo mode.
• Press the On/off button to turn the device off.
  Fig. 6
  
  

Upright Vacuum Cleaner

• Assemble the vacuuming tube (see section 3 “Product Assembly”)
• Press the On/off button to turn the device on.
• Press the power push button to select the desired power level.
• It will automatically operate in Eco mode. The power level can be adjusted at any moment by pressing this button.
• Press once to switch to Daily mode.
• Press again to operate it at Turbo mode.
• Press the On/off button to turn the device off.
• The device includes Auto Carpet that is activated automatically when it detects a carpet or a large amount of dirt.

Accessories
This device includes different accessories that allow cleaning different types of surfaces, objects and dirt. Some of them are suitable for the upright vacuum cleaner, and others are preferably used with the handheld one

Jalisco brush
Assemble this brush to the upright vacuum cleaner. This brush is designed especially for cleaning hard floors, but can be used to clean efficiently soft floors too. The brush counts on a protection system that avoids tangles and prevents the device from being damaged. As the brush stops rotating and the device stops operating automatically when it vacuums big objects or excessive dirt.
Fig. 7

Motorised upholstery brush
This brush should be used with the upright-vacuum cleaner to clean all types of upholstery.

Silicone and bristles brush
Interchangeable brush made of silicone and bristles, ideal for cleaning carpets and pet hair.
This accessory is used with the upright vacuum cleaner.

Extensible tube
This accessory is a extensible tube that is fitted into the handheld vacuum cleaner and is used as an adapter for the rest of accessories. It allows reaching less accessible areas.

2-in-1 wide brush for furniture and corners
This accessory is used with the handheld vacuum cleaner and allows cleaning furniture without damaging it and reaching less accessible dirt in corners.

2-in-1 narrow brush for furniture and corners
This accessory is used with the handheld vacuum cleaner and allows cleaning furniture without damaging it and reaching less accessible dirt in corners.

Union elbow
This accessory is used with the handheld vacuum cleaner as an angle-adjustment element. It is fitted into the handheld vacuum cleaner, and allows connecting the rest of accessories to it for a more comfortable and agile cleaning.

Long brush
This accessory is assembled to the handheld vacuum cleaner and can be used to clean any kind of surface.
Fig. 8

Wall bracket
This product includes a wall bracket that allows hanging the vacuum cleaner from the wall. The same bracket has different accessory holders that allow storing accessories while not in use.
It can be assembled with screws (included with the product), or with an adhesive (included with the product).
When using the adhesive, make sure to use it on a clear flat surface.
Also make sure that the suction base rests on the floor when hanging the device.
If not, it may fall.
Fig. 9

Charging
The device can be charged in 2 different ways. It can be charged directly through the handheld vacuum cleaner or the battery can be removed and charged separately.
It is important to charge it when the battery is low. The battery indicator will light as follows:
Steady green: 100-50 %
Steady orange: 50-25 %
Flashing red light: 25-0%
Disconnect it from the power adapter when the battery indicator is lit up in green.
**Fig. 10

**

CLEANING AND MAINTENANCE

• Do not use abrasive scouring pads, powders or cleaners to clean the product.
• Use a soft, dampened and clean cloth to clean the product’s outer housing.
• Do not let water enter into the vacuum cleaner.
• Keep the appliance in a cool, dry place and out of reach from children.
• Do not immerse the device in water and do not clean any of its parts in the dishwasher

Dust tank
To empty the dust tank, first disassemble the handheld vacuum cleaner from the rest of the unit. Use the tab on the dust tank to open its cover and empty it. If necessary, shake it gently to remove all the dust.
Fig. 11

To clean it, press the dust tank release button and turn the dust tank anticlockwise to the unlock position. Remove it. Use water to rinse it. If necessary, clean it with soap to remove all the dust.
Recommendation: It is suggested to clean the dust tank after each use.
**Fig. 12

**

Filters
It is suggested to clean the filters regularly to ensure maximum efficiency. They can be cleaned with warm water. Dry them thoroughly before installing them back in the device.

To take filters out:
Open the dust tank following the instructions on the before section.
Turn the metallic filter anticlockwise and remove it.
Fig. 13

Unscrew the plastic cyclone and remove it too.
Pull from the tab located on the top of the handheld vacuum cleaner and remove the high efficiency filter.
Wash all of them with warm water.
Allow them to dry completely before installing and using them again.
Fig. 14

Jalisco brush

Recommendation:
It is important to clean the brush regularly to avoid hair and other foreign objects from tangling and to prevent blockages.
Press the brush release button on the bottom part of the suction base and remove the brush.
Wash it with warm water. Do not use detergents or soap.
Make sure it is completely dry before installing it back in the device.
Fig. 15

WET ACCESSORY

Before use
Take the product out of the box.
Remove all packaging materials. Keep the original box.
Make sure all the components are included and in good conditions, otherwise, contact immediately the official Technical Support Service of Cecotec.
When you do not use the vacuum cleaner fora long time, please remove the water tank and empty the remaining water. Do not expose it to direct sunlight or to damp environments.

Mop installation/removal
Removing/installing the water tank
Fig. 16

In order to install/remove the cleaning cloth you must first disassemble the water tank from the rest of the appliance.
In order to remove the water tank, use your foot to hold it against the ground and pull upwards until it un clicks from position.
Once the cloth has been installed and the water tankhas been filled, to reinstall the water tank, simply push it back together until it clicks into position.
Note: Do not use cleaning agents. Use clean and room temperature water only. Do not use the vacuum cleaner to vacuum water.

Installing the mop cloth
Place the mop cloth on the ground with the Velcro facing upwards.
Align the mop cloth with the Velcro strips on the water tank and attach it.
**Fig. 17

**

Water emission
Fig. 18

When using this product for the first time, make sure the water tank lid is not fully open.
When not in use, pay attention to the water emission push button and to the tank lid, as water leak may occur when the water tank is full.
To activate water emission, the water emission push button must be pressed, and to stop water emission, the push button must be released as shown on the following figure:
Note: If the vacuum cleaner is not going to be used for a long period of time, make sure to remove the water tank and to empty the remaining water. Do not expose it to direct sunlight or to damp environments.

Removing the mop cloth
To remove the mop cloth, just hold it with your hand and pull form it to detach it from the water tank.

Cleaning and maintenance
Cleaning the tank
To clean the water tank, fill the tank with clean water, shake it and then empty it.
The mop is washable; therefore, it is suggested to wash it after every use.
Replace the cloth after 20-30 uses, depending on the use.
When the mop cloth is used for a long time, it is possible that the water output is affected.
This can be avoided by cleaning both cloth and water tank regularly.

TROUBLESHOOTING

The vacuuming tube, brush, battery, suction base or handheld vacuum cleaner are not assembled in place.

| Charge the vacuum cleaner. Check that the components and the handheld vacuum cleaner are assembled correctly.
Suction power level is very low.| The dust tank is full. Filters are dirty or blocked. Air inlet of the vacuuming tube or suction base are blocked.| Empty the dust tank. Clean or replace the filter.
Clean the dirt attached to the brush.
The operating time after charging has decreased.| It has not been enough charged.
Battery is damaged or too old.| Charge the battery completely.
Replace the battery.
Green and red light blinking.| The charger is not connected to the mains.| Plug the charger to a socket base.

Note: For any further doubt, please contact the official Technical Support Service of Cecotec.

TECHNICAL SPECIFICATIONS

Model: Conga RockStar 700 Ultimate ErgoWet
Battery: 25,9 DC, 2500 mAh
Product reference: 05494
Voltage and frequency: 100-240 V ~, 50/60 Hz
Made in China | Designed in Spain

DISPOSAL OF OLD ELECTRICAL APPLIANCES

 The European directive 2012/19/EU on Waste Electrical and Electronic
Equipment (WEEE), specifies that old household electrical appliances must not be disposed of with the normal unsorted municipal waste. Old appliances must be collected separately, in order to optimise the recovery and recycling of the materials they contain, and reduce the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the product reminds you of your obligation to dispose of the appliance correctly.
Consumers must contact their local authorities or retailer for information concerning the correct disposal of old appliances and/or their batteries.

TECHNICAL SUPPORT AND WARRANTY

This product is under warranty for 2 years from the date of purchase, as long as the proof of purchase is submitted, the product is in perfect physical condition, and it has been given proper use, as explained in this instruction manual.

The warranty will not cover the following situations:
The product has been used for purposes other than those intended for it, misused, beaten, exposed to moisture, immersed in liquid or corrosive substances, as well as any other fault attributable to the customer.
The product has been disassembled, modified, or repaired by persons, not authorized by the official Technical Support Service of Cecotec.

Faults deriving from the normal wear and tear of its parts, due to use.
The warranty service covers every manufacturing defects of your appliance for 2 years, based on current legislation, except consumable parts. In the event of misuse, the warranty will not apply.

If at any moment you detect any problem with your product or have any doubt, do not hesitate to contact Cecotec Technical Support Service at +34 963 210 728.

Support

http://www.cecotec.es/

Grupo Cecotec Innovaciones S.L.
C/ de la Pinadeta s/n, 46930
Quart de Poblet, Valencia (Spain)
PE01200619

References

• SmartGroup

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>