Einhell 45.120.64 Power-X-Boostcharger 6A Instructions
- June 5, 2024
- Einhell
Table of Contents
** Power-X-Boostcharger 6A
Original operating instructions Charger**
| **** | For use in dry rooms only. |
|---|---|
| Safety class II | |
| WARNING – Read the operating instructions to reduce the risk of injury“ |
Danger!
When using the equipment, a few safety precautions must be observed to avoid
injuries and damage. Please read the complete operating instructions and
safety regulations with due care. Keep this manual in a safe place, so that
the information is available at all times. If you give the equipment to any
other person, hand over these operating instructions and safety regulations as
well. We cannot accept any liability for damage or accidents which arise due
to a failure to follow these instructions and the safety instructions.
Safety regulations
Danger! Read all safety regulations and instructions. Any errors made in
following the safety regulations and instructions may result in an electric
shock, fi re, and/or serious injury. Keep all safety regulations and
instructions in a safe place for future use.
This equipment can be used by children of 8 years and older and by people with
limited physical, sensory or mental capacities or those with no experience and
knowledge if they are supervised or have received instruction in how to use
the equipment safely and understand the dangers which result from such use.
Children are not allowed to play with the equipment. Unless supervised,
children are not allowed to clean the equipment and carry out user-level
maintenance work.
Replacing the power cable If the power cable for this equipment is damaged, it must be replaced by the manufacturer or OEM after-sales service or by similarly trained personnel to prevent hazards.
a) The charging unit is not allowed to be used for non-rechargeable, normal
batteries.
b) Suffi client ventilation is required.
c) The current and voltage information on the battery pack must be the same as
that on the charging unit.
d) Do not expose the charging unit to splash water or rain.
e) Do not throw old or damaged batteries into water or fi re. Follow the
environmental protection directives.
f) A defective or no longer chargeable battery must be treated as special
waste. Dispose of it at a special collection point. Do not dispose of it with
your normal household waste or throw it into water or fi re.
g) Place the charging unit away from all sources of heat.
h) To reduce the risk of electric shock, pull the power plug out of the
socket-outlet by the plug itself and not by the cable when you want to
disconnect the charging unit from the power supply.
i) Do not take the charging unit apart. Take it to an authorized repair center
if servicing or repairs are needed. Incorrect assembly can result in an
electric shock and even death or fi re.
j) Children must always be supervised in order to ensure that they do not play
with the equipment.
Layout (Fig. 1)
- Charger
- Charging cable
- Boost button
Technical data
Charger
Input …………………… 220-240V~50-60Hz, 150 W
Output (normal) ………………………… 18 V d.c., 3A
Output (boost) ………………………….. 18 V d.c., 6A
Caution!
The charging unit is allowed to be used only for the lithium-ion batteries of
the Power-X-Change series!
Operation (Fig. 1-3)
- Pull the battery pack (a) out of the handle, pressing the push-lock button (b) as you do so.
- Check that your mains voltage is the same as that marked on the rating plate of the battery charger. Insert the power plug of the charger (1) into the socket outlet. The green LED will then begin to fl ash.
- Insert the battery pack (a) into the battery charger (1).
- In section 7 „Charger indicator“ you will find a table with an explanation of the LED indicator on the charger.
- Boost charging In boost charging mode the rechargeable battery is charged more quickly than in normal high-speed charging mode. Press the boost button (3) to switch to boost charging mode. This is indicated by the blue LED. (see point 7)
Important!
Boost charging is recommended when the battery needs to be got ready for work
again quickly.
If the battery is not required again quickly after use, recharge it in normal
high-speed charging mode, because of this mode of charging places less stress
on the lithium-ion battery.
If the battery fails to charge, please check
- whether there is the voltage at the socket-outlet
- whether there is good contact at the charging contacts of the charging unit
If the battery still fails to charge, send
- the charging unit
- and the rechargeable battery to our customer service center.
To ensure that items are properly packaged and delivered when you send them to
us, please contact our customer service or the point of sale at which the
equipment was purchased.
When shipping or disposing of batteries and cordless tools, always ensure that
they are packed individually in plastic bags to prevent short circuits and fi
res.
Mounting the charging unit on a wall (Fig. 4)
The charging unit can also be mounted on a wall.
The correct dimensions for drilling holes in the wall can be found on the back
of the charging unit.
Spacing distances
≥ 10 cm from the wall (right + left)
≥ 100 cm from the ceiling
Caution!
When mounting on a wall you must use suitable screws, e.g. 3.5 mm pan-head
screws, in order to prevent damage to the housing and risk of falling.
Cleaning and maintenance
Always pull out the power plug before starting any cleaning work.
The equipment is not allowed to be stored in a damp location or where there
are caustic gases.
Keep it in a dry place out of the reach of children.
Always pull out the power plug before starting any cleaning work.
The equipment is not allowed to be stored in a damp location or where there
are caustic gases.
Keep it in a dry place out of the reach of children.
5.1 Cleaning
Keep the surface of the equipment clean and wipe it only with a dry cloth.
5.2 Maintenance
There are no other parts inside the equipment which require maintenance. The
equipment is not allowed to be taken apart. If the equipment is damaged,
contact your supplier or the manufacturer.
Disposal and recycling
The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Defective components must be disposed of as special waste. Ask your dealer or your local council.
Charger indicator
Indicator status
| Explanations and actions
---|---
Blue LED
| Red LED|
Green LED
| Off| Flashing| Ready for use
The charger is connected to the mains and is ready for use; there is no
battery pack in the charger
| On| Off| Charging
The charger is charging the battery pack in quick charge mode. The charging
times are shown directly on the charger. Important! The actual charging times
may vary slightly from the stated charging times depending on the existing
battery charge.
| Off| On| The battery is charged and ready for use.
The unit then changes over to gentle charging mode until the battery is
fully charged.
To do this, leave the rechargeable battery on the charger for approx. 15
minutes longer. Action:
Take the battery pack out of the charger. Disconnect the charger from the
mains supply.
| Flashing| Off| Adapted charging
The charger is in gentle charging mode.
For safety reasons the charging is performed less quickly and takes more time.
The reasons can be:
– The rechargeable battery has not been used for a very long time.
– The battery temperature is outside the ideal range. Action:
Wait for the charging to be completed; you can still continue to charge the battery pack.
| Flashing| Flashing| Fault
Charging is no longer possible. The battery pack is defective. Action:
Never charge a defective battery pack.
Take the battery pack out of the charger.
| On| On| Temperature fault
The battery pack is too hot (e.g. due to direct sunshine) or too cold
(below 0° C).
Action:
Remove the battery pack and keep it at room temperature (approx. 20° C) for
one day .
On| On/Off/ flashing| On/Off/ Flashing| Boost mode
The charger is in boost mode. The indicator status of the red + green LEDs
applies here too.
For EU countries only
Never place any electric power tools in your household refuse.
To comply with European Directive 2012/19/EC concerning old electric and
electronic equipment and its implementation in national laws, old electric
power tools have to be separated from other waste and disposed of in an
environment-friendly fashion, e.g. by taking to a recycling depot.
Recycling alternative to the return request:
As an alternative to returning the equipment to the manufacturer, the owner of
the electrical equipment must make sure that the equipment is properly
disposed of if he no longer wants to keep the equipment.
The old equipment can be returned to a suitable collection point that will
dispose of the equipment in accordance with the national recycling and waste
disposal regulations. This does not apply to any accessories or aids without
electrical components supplied with the old equipment.
The reprinting or reproduction by any other means, in whole or in part, of
documentation and papers accompanying products, is permitted only with the
express consent of the Einhell Germany AG.
Subject to technical changes
Warranty certificate
Dear Customer,
All of our products undergo strict quality checks to ensure that they reach
you in perfect condition. In the unlikely event that your device develops a
fault, please contact our service department at the address shown on this
guarantee card. You can also contact us by telephone using the service number
shown.
Please note the following terms under which guarantee claims can be made:
-
These guarantee terms apply to consumers only, i.e. natural persons intending to use this product neither for their commercial activities nor for any other self-employed activities. These warranty terms regulate additional warranty services, which the manufacturer mentioned below promises to buyers of its new products in addition to their statutory rights of guarantee. Your statutory guarantee claims are not aff ected by this guarantee. Our guarantee is free of charge to you
-
The warranty services cover only defects due to material or manufacturing faults on a product which you have bought from the manufacturer mentioned below and are limited to either the rectifi cation of said defects on the product or the replacement of the product, whichever we prefer.
Please note that our devices are not designed for use in commercial, trade or professional applications. A guarantee contract will not be created if the device has been used
by commercial, trade or industrial business or has been exposed to similar stresses during the guarantee period. -
The following are not covered by our guarantee:
– Damage to the device caused by a failure to follow the assembly instructions or due to incorrect installation, a failure to follow the operating instructions (for example connecting it to an incorrect mains voltage or current type) or a failure to follow the maintenance and safety instructions or by exposing the device to abnormal environmental conditions or by la ck of care and maintenance.
– Damage to the device caused by abuse or incorrect use (for example overloading the device or the use or unapproved tools or accessories), ingress of foreign bodies into the device (such as sand, stones or dust, transport damage), the use of force or damage caused by external forces (for example by dropping it).
– Damage to the device or parts of the device caused by normal or natural wear or tear or by normal se of the device. -
The guarantee is valid for a period of 24 months starting from the purchase date of the device. Guarantee claims should be submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fi tted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or parts fitted. This also applies if an on-site service is used.
-
To make a claim under the guarantee, please register the defective device at: www.Einhell-Service.com. Please keep your bill of purchase or other proof of purchase for the new device. Devices that are returned without proof of purchase or without a rating plate shall not be covered by the guarantee, because appropriate identification will not be possible. If the defect is covered by our guarantee, then the item in question will either be repaired immediately and returned to you or we will send you a new replacement.
Of course, we are also happy off er a chargeable repair service for any defects
which are not covered by the scope of this guarantee or for units that are no
longer covered. To take advantage of this service, please send the device to
our service address.
Also refer to the restrictions of this warranty concerning worn parts,
consumables, and missing parts as set out in the service information in these
operating instructions.
Declaration of conformity: We declare conformity in accordance with the EU directive and standards for article
*Ladegerät Power-X-Boostcharger 6A (Einhell)**
2014/29/EU
2005/32/EC2009/125/EC
(EU)2015/1188
X 2014/35/EU
2006/28/EC
X 2014/30/EU
2014/32/EU
2014/53/EU
2014/68/EU
(EU)2016/426
Notifi ed Body:
(EU)2016/425
X 2011/65/EU(EU)2015/863| 2006/42/EC
Annex IV
Notifi ed Body:
Reg. No.:
2000/14/EC2005/88/EC
Annex V
Annex VI
Noise:
measured LWA
= dB (A); guaranteed LWA= dB (A)P = kW; L/Ø = cm
Notifi ed Body:
2012/46/EU(EU)2016/1628
Emission No.:
---|---
Standard references: EN 60335-1; EN 60335-2-29; EN 62233;
EN 61000-3-2; EN 61000-3-3; EN 55014-1; EN 55014-2
ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar
Landau/Isar, den 04.05.2021
First CE: 17
Art.-No.: 45.120.64
I.-No.: 21021
Subject to change without notice| Archive-File/Record: NAPR025543
Documents registrar: Egginger Christoph
Wiesenweg 22, D-94405 Landau/Isar
---|---
Charger
UK CA Declaration of conformity
We, Einhell UK Ltd
Champions Business Park, First Floor Unit 10, Arrowe Brook Rd, Upton, Wirral
CH49 0AB, United Kingdom declare the conformity to UK standards and
legislation was assessed for:
Charger Power X-Booscharger 6A (Einhell)
UK legislation
Simple Pressure Vessels (Safety) Regulation Electrical Equipment (Safety)
Regulation Radio Equipment Regulation Personal Protective Equipment Regulation
The Ecodesign for Energy-Related Products and Energy Information Regulation
X The Restriction of the Use of Certain Hazardous Substances in Electrical and
Electronic Equipment Regulation
Noise Emission in the Environment by Equipment for use Outdoors Regulation
Noise:
measured LWA
= dB (A); guaranteed LWA
= dB (A)
Supply of Machinery (Safety) Regulation
Annex IV
Notifi ed Body:
Reg. No.:| X Electromagnetic Compatibility Regulation
Measuring Instruments Regulation
Pressure Equipment (Safety) Regulation
---|---
Standards: BS 60335-1; BS 60335-2-29; BS62233;
BS 55014-1; BS 55014-2; BS 61000-3-2; BS 61000-3-3
Wirral, 2021.05.04
Article Number: 45.120.64 I.-No.: 21021
Subject to change without notice| Archive-File/Record: NAPR025543
Documents registrar: Egginger Christoph
Wiesenweg 22, 94405 Landau/Isar, Germany
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>