FOS technologies ATLAS Tube Wireless RGBW Battery Tube Instruction Manual
- June 4, 2024
- FOS technologies
Table of Contents
FOS technologies ATLAS Tube Wireless RGBW Battery Tube
Introduction
Security Warning
- When unpacking and before disposing of the carton, check if there is any transportation damage before using the product. Should there be any damage caused by transportation, consult your dealer and do not use the apparatus.
- Product should install in a cool place.
- The product is only intended for installation, operation and maintenance by qualified personnel. And read the user manual and labels on the lighting carefully before use.
- Please do not attempt to dismantle and/or modify the product inner structure.
- Electrical connection must only be carried out by qualified personnel.
- Do not connect this device to any other types of dimmer apparatus.
- There are protection structure and circuit for the battery inside the unit, any inappropriate dismount of the light or battery might break the protection function and lead to batter getting hot, smoking, deforming or fire.
- Never short-circuit the unit.
- Heating and burning will melt the battery separator, causing loss of protection function or burning of electrolyte and overheat will cause heating, smoking, deformation or burning of batteries.
- Never use the unit in an environment over 40℃, don’t charge the unit close to fire source or under direct sun. Don’t throw the unit to water, otherwise, the protection function inside the batter might lose or abnormal chemical reaction might arise, causing battery to be hot, smoking, deformation or fire.
- Use only the supplied power supply, for charging the fixture.
- Place the unit where kids can’t reach.
- If the charging time over the standard charging time for long, it is advised to stop charging. It will extend the charging time if charging while using, it is advised to turn off the light when charging.
- Not to use the unit in an environment where there is static electricity, the battery protection circuit might easily malfunction.
- Use the supplied power adapter only, never charging over 24 hours.
- When not using the unit for long term, please save the unit properly in a dry place, battery should be half charged.
- Please recycle the used unit, never throw to fire or water.
If you have any questions, don’t hesitate to consult our dealer or
manufacturer.
Important: Before any installation, maintenance and cleaning, please ensure
that the power cut off!
Main Technical Parameters
Lithium battery
- Charging Voltage: DC12.6V/2A
- Battery Specification: 21700 4.2V/4.5Ah*12 cells (12.6V/18Ah)
- Charge Time: 8~10 hours
- Circulation Life: Not less than 300 times / Run Time Of Battery: Max. 20h
LED
- LED Type: 288pcs ×0.3Watts RGBW 4in1 full-color LED
- Control Pixel: 32 Pixels
- Rated Power: 50W
- Colors: 16.7 million colors (0~100% saturation dimming) / Life: 50000 hours
Control
- Control Protocol: International standard DMX-512 signal
- Channel Protocol: 7 kinds of control channel mode. 2CH; 4CH; 6CH; 11CH; 32CH -8 Pixels; 64CH -16 Pixels; 128CH -32 Pixels;
- Control Mode: DMX-512, auto, master-slave, music, infrared remote control, wireless DMX-512 and Mobile APP WIFI control.
- Wireless Protocol: W-DMX
Wireless DMX Specs
- 2.4G Communication Distance: 200M (clearing, it changes vary with different environments)
- WIFI Communication Distance: 30M (clearing, it changes vary with different environments)
- Band: 2.4G ISM, 126 channel frequencies
- Maximum Transmit Power: 20dBm
- Receiver Sensitivity: -94dBm
Optical System
- Dimmer: From 0 -100 linear dimming.
- Flashing Rate: 1 -20Hz / Beam Angle: 180°
Physical
- Dimensions: Ø52 x 1190 mm
- Weight: 1.72kg
Security
- Cooling System: Convection
- Waterproof Rate: IP65
- Temperature Protection: 60℃
- Operating Environment: Indoor / Outdoor
Product Features
Using the latest LED control technology, this product is designed for stage and event sites and can be used to create stunning lighting effects. Its main features include：
- Product built-in lithium battery and the DMX signal wireless module.
- Product built-in WIFI receiving module, which can be controlled by mobile APP.
- Wireless DMX with transceiver function.
- With music control function.
- Custom color temperature settings.
- Built-in commonly used film and television shooting effects.
- With charging protection and current overload protection.
- Intuitive and convenient battery display function.
- The static power consumption of the control panel is 0.3W, and its efficiency will reach up to 97% during the process of high-power output, which realizes the function of eco-friendly operation.
- Overheating automatic protection function.
- IR infrared remote-control panel.
- Touch button and LCD display.
- Password protected keyboard.
- 7 kinds of DMX working modes.
- Built-in 68 kinds of Auto effect.
- Master-slave control, multi-units for synchronous wireless control.
- Software system updates & upgrades are available through DMX 512 or wireless DMX.
Product Packing Information
Following accessories are packed together with the product, please check them
carefully upon unpacking.
Product Installation
DMX Connection Method
When set the DMX512 address code be CH4 MODE, as below:
- The Wireless DMX transmitter should connected to the DMX-512 controller.
- Since CH4 MODE has 4 channels, address code with 4 increments increasing progressively ( e.g., 1 , 5 ,9, 13 …)
- Every DMX address code can be reused as needed.
- DMX address code can be any data
2.4G-Wireless Master-Slave Connection Method
- Set the wireless DMX signal of the first light to the sending state (Master), and the wireless DMX signal of other lights to the receiving state (Slave).
- When the Slave is set to DMX512 control mode, running auto effect or other static colors on the Master to achieve the wireless master-slave synchronization.
- The DMX address code of the Master and Slave can be any data between 001 and 512 without affecting master-slave online.
Mobile APP WIFI Master-Slave Connection Method
As below:
- Establish wireless communication between WIFI control of mobile phone and WIFI control of lights according to 3.5.7.
- Set the wireless DMX signal of the first light to the sending state (Master), and the wireless DMX signal of other lights to the receiving state (Slave).
- When the Slave is set to DMX512 control mode, running auto effect or other static colors on the phone APP to achieve the wireless master-slave synchronization.
- The DMX address code of the Master and Slave can be any data between 001 and 512 without affecting master-slave online.
Operation Method
Back panel function’s introduction
- M: Menu button/return button, enter the menu selection interface or previous menu.
- E: Confirmation button, used to confirm the selected function.
- ▲ / ▼：Upward/downward select function or Parameter increment / decrement.
- POWER IN DC12.6V/2A ：Charging port, both available.
- DMX IN / OUT： DMX-512 signal Input / Output.
2.4G Wireless DMX Connection Method
Working mode
2.4G wireless DMX transceiver uses the W-DMX communication protocol which has
two working modes：
Transmit mode and Receive mode.
- Find【Set】menu and press【ENTER】 to enter system settings menu.
- Press【UP/DOWN】key to select【Wireless 2.4g】to enter 2.4g wireless DMX settings menu.
- 【 WIRELESS 】 for wireless DMX control ON/OFF. 【CONNECT】means the paired connection of wireless
- DMX module. 【RESET】means reset the data of wireless DMX control setting,【MODE】has transmitting mode and receiving mode.
Note: The wireless transceiver will remember the chosen protocol even after you disconnect the power supply. There is no need for repeated setting.
Working mode
- According to step 3.2.1 set, the Slave to 【 Receive 】 mode.
- Select【 Reset 】menu to reset wireless connection. At this time, the indicator light is white, indicating that the wireless module is not connected to transmit module and is ready to receive the paired signal.
- According to step 3.2.1 set the Master to【 T ransmit】 m ode. At this time, the indicator light is blue slow flash, indicating that the wireless module is not connected to DMX signal.
- Selec【Reset 】m enu to reset wireless connection. At this time, the indicator light is red, indicating that the connected receiving module is being deleted.
- Select 【 CONNECT 】 to transmit wireless paired signal, at this time the indicator light is blue fast flash.
- When the Slave receive the paired signal from Master, the indicator light is Green fast flash which means the connection is established.
Infrared Remote Controller Instruction
- Dimming up
- Dimming down
- Off: light off
- ON: light on
- R / G / B / W for 4 single color, A / UV (None)
- 9 number keys means 9 kinds of static mix color (AC1……AC9)
- The “0” key for is to enter the DMX-512 control state
- The AUTO key is color change mode, press up and down key to adjust speed
- STROBE key is in color strobe mode (32 types are optional), press up and down key to adjust speed.
- The FADE key is for color fading mode, press up and down key to adjust speed.
- The SOUND key is for sound control mode, press up and down key to adjust the sound control sensitivity.
Note: The IR remote controller should be pointed at the IR infrared receiver
Menu Display
Menu Overview
DMX Address Settings (Dmx512)
- Find【DMX Mode】menu and press【ENTER】to enter DMX address code setting.
- Press【UP/DOWN】button to adjust parameters.
- After setting the DMX address code, press【ENTER】to save the settings
Auto Effect Settings (Auto)
- Find【Auto】menu and press【ENTER】to enter auto effect setting.
- Press【UP/DOWN】button to select【Auto Mode】,【Speed】or【Color】.
- Press【ENTER】to enter the settings.
- Press【UP/DOWN】button to select auto effect, speed, or color, press【ENTER】to save the settings.
Sound Effect Settings (Sound)
- Find【Sound】menu and press【ENTER】to enter sound effect setting.
- Press【UP/DOWN】button to select【Sound Mode】,【Sens】or【Color】.
- Press【ENTER】to enter the settings.
- Press【 UP/DOWN】 button to select sound effect, sound control sensitivity or color effect, press 【ENTER】 to save the settings.
Static Color Settings (Static)
- Find【Static】menu and press【ENTER】to enter static color setting.
- Press【UP/DOWN】button to select【Dimmer】,【Strobe】,【Red】,【Green】,【Blue】or【White】.
- Press【ENTER】to confirm menu and press【UP/DOWN】button to adjust parameters, then press 【ENTER 】to save the settings.
Built-in Static Color Settings (Color)
- Find【Color】menu and press【ENTER】to enter built-in static color setting.
- Press【UP/DOWN】button to select【Red】,【Green】,【Blue】… 15 built-in colors.
- Press【ENTER】to save the settings.
Color Temperature Settings (CCT)
- Find【CCT】menu and press【ENTER】to enter color temperature setting.
- Press【UP/DOWN】button to select【2800K】【3000K】【3200K】… 18 kinds of color temperature effect.
- Press【ENTER】to save the settings. Hold 【ENTER】for more than 3 seconds to enter the screen for customizing the current color temperature.
- Built-in【Red】,【Green】,【Blue】,【White】4 base colors with 0~255 brightness adjustment, can freely customize the current color temperature according to your needs.
Mobile APP Control Mode Settings (WIFI)
- Find【WIFI】menu and press【ENTER】to turn on WIFI.
- “Led_XXX” displayed on the screen is the WIFI address of the light fixture.
- Scan the above QR code to install 【LED LAMP】APP first on mobile phone.
- On the phone, find WIFI and search WIFI address, and the words beginning with LED appear. For example, “LED-XXX”, click the link.
- Turn on the【LED LAMP】APP installed on the phone and show the link is successful then you can control it.
System Settings
- Find【Set】menu and press【ENTER】to enter system setting.
- Press【UP/DOWN】button to select the corresponding function setting.
- After setting, press【ENTER】to save the settings.
Factory Settings (Factory Set)
- Find【Factory】menu and press【ENTER】to enter factory setting.
- Press【UP/DOWN】button to select the corresponding function setting.
- After setting, press【ENTER】to save the settings.
Note: This the factory default setting, do not change it if unnecessary.
Menu Lock Function (Menu Lock)
- Form 【Set】 menu to find 【Menu Lock】 menu.
- Press【ENTER】button to enter select 【ON】.
- When the menu locked, at the same time long press button▼▲ , the display appears a small lock icon and have a number count down to “0”, it will unlock successfully.
Charging Display
Note: In the process of charging, the display screen will have a charging display. If the lamp needs to work while charging, long press【MENU】button to enter for operate menu.
Control Channel
DMX Channel Table
2CH 2CH Mode:
4CH 4CH Mode:
6CH 6CH Mode:
11CH 11CH Mode:
32CH 32CH Mode:
64CH 64CH Mode:
128CH 128CH Mode:
Maintenance
Product Maintenance
To prolong the life of the product, it is very important to do maintenance
work. The environment is hash outdoors, or if the product is idle for a long
time, damp, smoke or particularly dirty surroundings can cause greater
accumulation of dirt on its LED lens cover, fan vents, and housing. So, it
should be cleaned to maintain an optimum light output and at the same time to
prevent it from being corrupted by acid gas.
Cleaning frequency depends on the environment in which the fixture operates.
Soft cloth and typical glass cleaning products should be used for cleaning. It
is recommended to clean the product at least once every 20 days.
Friendly Notice: Please do not use any organic solvent, e.g., alcohol to
clean the housing of the apparatus, it will cause damage.
Trouble Shooting
Documents / Resources
| FOS
technologies ATLAS Tube Wireless RGBW Battery
Tube
[pdf] Instruction Manual
ATLAS Tube, Wireless RGBW Battery Tube, ATLAS Tube Wireless RGBW Battery Tube
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>