Clarke CAM30B 230V 30 Inch Drum Fan Instruction Manual

Air 30 INCH DRUM FAN 230V
MODEL NO: CAM30B
PART NO: 3231567

**OPERATION & MAINTENANCE
INSTRUCTIONS

ORIGINAL INSTRUCTIONS
GC0521
**

INTRODUCTION

Thank you for purchasing this CLARKE 30” Drum Fan.

Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service.

SPECIFICATIONS

ELECTRICAL CONNECTIONS

WARNING! READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS SUPPLY.

Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. Connecting it to any other power source may cause damage.

This product may be fitted with a non-rewireable plug. If it is necessary to change the fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or damaged, the plug must not be used until a suitable replacement is obtained.

If the plug has to be changed because it is not suitable for your socket, or due to damage, it should be cut off and a replacement fitted, following the wiring instructions shown below. The old plug must be disposed of safely, as insertion into the main socket could cause an electrical hazard.

If the colors of the wires in the power cable of this product do not correspond with the markings on the terminals of your plug, proceed as follows.

• The Blue wire must be connected to the terminal marked N or colored Black.
• The Brown wire must be connected to the terminal marked L or coloured Red.
• The Yellow and Green wire must be connected to the terminal marked E or colored Green.

The plug must be BS1363/A approved.

Ensure that the outer sheath of the cable is firmly held by the clamp

We strongly recommend that this machine is connected to the mains supply via a Residual Current Device (RCD)

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs yourself.

SAFETY PRECAUTIONS

1. ALWAYS read the manual before use.
2. Suitable for indoor use only.
3. Avoid using in dusty environments.
4. DO NOT use in environments containing chemical fumes etc.
5. DO NOT use it as an extractor fan.
6. DO   NOT use in areas of high humidity/water vapor, i.e. bathrooms, etc.
7. DO NOT connect the fan to the duct system.
8. DO NOT cover the fan with clothing or any material that will restrict free airflow through the fan.
9. NEVER touch the blades with your hand or any loose object.
10. ALWAYS unplug the fan before moving it or performing maintenance.
11. DO NOT touch the fan when your hands are wet.
12. ALWAYS unplug the fan when it is not in use.
13. NEVER unplug the fan by holding the cable. Unplug by holding the plug.
14. NEVER use the fan if the cable or plug is damaged.
15. NEVER use the fan close to fires.
16. DO NOT use this fan with any solid-state speed control device to reduce the risk of fire or electric shock.
17. Those who are not qualified electricians should not disassemble or repair this product.

ENVIRONMENTAL RECYCLING POLICY

Through the purchase of this product, the customer is taking on the obligation to deal with the WEEE in accordance with the WEEE regulations in relation to the treatment, recycling & recovery, and environmentally sound disposal of the WEEE.
In effect, this means that this product must not be disposed of with general household waste. It must be disposed of according to the laws governing Waste Electrical and Electronic Equipment (WEEE) at a recognized disposal facility.

OPERATION

Turn the switch on the speed regulator to select the fan speed required.

| CAM30B
---|---
Position 1| 850 RPM
Position 2| 919 RPM

MAINTENANCE

WARNING: NEVER OPERATE THE FAN WITH THE FRONT OR REAR GUARDS REMOVED.

Have any repairs been carried out by a suitably qualified person?

• The motor bearings are permanently sealed for life and do not require any additional lubrication.

If the fan has been operating for long periods in a very dusty environment, the blades and motor assembly may eventually require cleaning.

1. Disconnect the power cable from the power supply.

2. Unscrew the front guard and lift it away carefully.

3. Wipe the fan blades with a dry cloth and remove any dust from the motor assembly with a soft paintbrush, vacuum cleaner or jet of compressed air.
   • Always wear suitable eye protection when using compressed air.
   • Never use polish or any corrosive liquid that will damage the surface finish.

4. Replace the guard securely before use.

PARTS LIST AND DIAGRAM

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for its intended purpose. Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission. This guarantee does not affect your statutory rights.

DECLARATIONS OF CONFORMITY

INTERNATIONAL
Hemnall Street, Epping, Essox CM16 4LG
DECLARATION OF CONFORMITY
This is an important document and should be retained.

We hereby declare that this product(s) complies with the following statuary requirements(s):
Electromagnetic Compatibility Regulations 2016,
Electrical Equipment (Safety) Regulations 2016
The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012

The following standards have boon applied to the product(s):
EN 61000-3-2:2014, EN 62233:2008, EN 55014-1.2017, EN 55014-2:2015,
EN 61000-3-3:2013, EN 60335-1:20124.A11.2014M12:2017+A1:2019+A14:2019+A2:2019,
EN 60335-2-80:2003+A1:2004+A2:2009,

The technical documentation required to demonstrate that the product(s) meet(s) the requirement(s) of the aforementioned legislation has been compiled and is available for inspection by the relevant enforcement authorities.

The UKCA mark was first applied in 2021

Product Description: 24″, 30″ 230V Drum fans
Model number(s): CAM24B, CAM3OB
Serial/batch Number: N/A
Date of Issue: 19105/2021
Signed:

** J.A. Clarke
Director**

CAM24B. CA143013 Drum ram UKCA D O C (rev0)

INTERNATIONAL
Fitzwilliam Hall. Fitzwilliam Place, Dublin 2
DECLARATION OF CONFORMITY
This is an important document and should be retained.

We hereby declare that this product(s) complies with the following directive(s):
2014/30/EU Electromagnetic Compatibility Directive.
2014/35/EU Low Voltage Equipment Directive.
2011165/EU Restriction of Hazardous substances.

The following standards have been applied to the product(s):
EN 61000-3-2:2014, EN 62233:2008, EN 55014-1:2017, EN 55014-2:2015,
EN 61000-3-3:2013, EN 60335-1:2012+A11:2014+Al2:2017+A1:2019+A14:2019+A2:2019,
EN 60335-2-80:2003+,41:2004+A2:2009

The technical documentation required to demonstrate that the product(s) meet(s) the requirement(s) of the aforementioned directive(s) has been compiled and is available for inspection by the relevant enforcement authorities.

The CE mark was first applied in 2011

Product Description: 24′, 30″ 230V Drum fans
Model number(s): CAM24B, CAM3OB
Serial/batch Number: N/A
Date o f Issue: 19/05/2021
Signed:

J.A. Clarke
Director
CAM24B, CAM30B Drum fans D 0 C (rev0)

A SELECTION FROM THE VAST RANGE OF

| QUALITY PRODUCTS AIR COMPRESSORS
From DIY to industrial, Plus air tools, spray guns, and accessories.
GENERATORS
Prime duty or emergency standby for business, home, and leisure.
POWER WASHERS
Hot and cold, electric and engine driven – we have what you need
WELDERS
Mig, Arc, Tig, and Spot. From DIY to auto/industrial.
METALWORKING
Drills, grinders, and saws for DIY and professional use.
WOODWORKING
Saws, sanders, lathes, mortisers, and dust extraction.
HYDRAULICS
Cranes, body repair kits, and transmission jacks for all types of workshop use.
WATER PUMPS
Submersible, electric, and engine-driven for DIY, agriculture, and industry.
POWER TOOLS
Angle grinders, cordless drill sets, saws, and sanders.
STARTERS/CHARGERS
All sizes for car and commercial use.|
---|---|---

PARTS & SERVICE: 0208 988 7400
Parts Enquiries
Parts@clarkeinternational.com
Servicing & Technical Enquiries
Service@clarkeinternational.com
SALES: UK 01992 565333 or Export 00 44 (0)1992 565335
INTERNATIONAL
Hemnall Street, Epping, Essex CM16 4LG
www.clarkeinternational.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>