Heiman 601011867-WS3MS Smoke Alarm User Manual

Heiman 601011867-WS3MS Smoke Alarm

Product Introduction

This smart motion sensor is for domestic premises, adopts WiFi wireless technology, and can real-time report the state if somebody passed. It uses automatic threshold adjustment technology to enhance the stability of the sensor and efficiently anti-false alarm. Automatic temperature compensation technology can prevent sensors from the decrease in sensitivity resulting from temperature variation.

Illustration

Technical Data

• Operating Voltage : DC3V (CR123A/CR17335x1)
• Detecting Distance: max. 9m under 25°C (detect distance will be different, depending on environment temperature)
• Detection Angle: 90
• Networking: WiFi -2.4GHz
• Wifi Protocol: IEEE 802.11 b/g/n
• Working temperature: -10°C +50°C
• Working Humidity: <95%(no condensation)
• Pet Protection level: 11kg or less
• Dimension: p80mm x H28.5mm

Download App & Networking

Scan the QR code above to download the Smart Life APP and register a user account.

• The guide may be a little different from the description in App. due to software updates. Pls, follow the guide in App when operating.
• Pls move the detector close to the router and try again, if networking failed.
• Make sure WiFi configuration succeeds before installation.
• This sensor is a 1OT device, using the latest software can get a better user experience.

Click”+”on the APP to add a new device, select “Security & Sensors>Motion Detector ( Wi-Fi )”

• Push the bracket in the direction of the arrow. (Figure 1)
• Remove the insulating film to power on the motion sensor and the device will enter into a warm-up state. Blue LED will flash for 30 seconds and then go off, indicating warm-up is finished. (Figure 2)

Method one
EZ networking:
Long press the network button for 5 seconds, and a blue LED flashes quickly (around 2 times per second). Pls, follow the guide in App when operating until networking success.

Method two
AP networking:
Long press the network button for 5 seconds, and make sure the blue LED flashes quickly (around 2 times per second). press the network button again for 5 seconds until blue LED flash slowly  around once / three seconds) s follow the guide in App when operation until networking success.

LED indicator status

LED Indicator

|

Product Status

---|---

Blue LED quickly flashing

|

EZ networking

Blue LED slow flashing

|

AP networking

Blue LED off

| Networking success or failure

Blue LED flash onetime

|

Alarm

Power on sensor,

blue LED flashes 30 second

|

Warm-up

sensor Detection Mode Description

Detection Mode Instruction
The sensor will enter a warm-up period (this period last around 30s ) after power on; When the warm-up period is finished, the sensor enters test mode (this period last around 5 minutes): A power-saving mode will be executed after the test mode.
Warm-up period: Blue LED flash in 30 seconds; Test mode: Detection interval is 10 seconds, the sensor will report “somebody pass by” immediately when detecting somebody pass;
Power-saving mode: It won’t repeat report alarm within 10 minutes since the last report of “somebody pass by”. Sensor will report “nobody pass” if nobody pass in 10 minutes, and it will report an alarm if being triggered after receiving a report of “nobody pass”.
Pet Immunity
Installed under recommended height, the sensor won’t alarm when pets (weight less than 11kg) pass by. (Customer experiences will differ in different installation environments).

Installation Precautions

• This product is for indoor use only.
• When installing, note that the LED should face upwards
• Avoid installing the sensor outdoors, or in places with pets, or near air-conditioners, heat sources, rotating objects, or in places with direct sunshine.
• The installation surface should be solid without vibration.
• Please install the sensor in places where an intruder may pass easily.

Product Installation

Paste the sensor in the proper area after removing double-side tape on the bracket.
Suggest installing use screws. If installation using a sticker, pls note:

1. Ensure that the installation surface is smooth, flat, firm, dry and clean;
2. It is necessary to regularly check whether the sensor adheres firmly after installation.
   User shall be responsible for the product falling off, damage and other usage conditions caused by the failure to use according to the manual.

LED light and bracket arrow up after successful installation.
The “arrow icon should point up toward the ceiling while installing the bracket. Then install the sensor onto the bracket.

Detecting Area

statement

• The information in the user manual is for reference only and does not constitute any form of commitment.
• Without the written permission of the manufacturer, any individual or organization shall not extract or copy part or all of the contents of this user manual, and shall not spread it in any form.
• As the technology is constantly updated, the manufacturer reserves the right to modify the user manual without prior notice. If the user manual and the actual operations is nconsistent, the final interpretation is reserved to the manufacturer herein.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>