BOYO VTM7012QFHD 4 Channel Vehicle Monitoring System User Manual

VTM7012QFHD
VTM9003QFHD

4 Channel Vehicle Monitoring System
with Digital Video Recorder
User Manual

Warranty

Quality of products is very important to us and BOYO provides a warranty against manufacturer’s defects for one year from the date of purchase. For warranty details, please visit http://visiontechamerica.com/pages/get- warranty. Please note that the warranty does not cover:

1. Accident or damage caused by misuse such as dropping the monitor, hitting the monitor, scratching the monitor, cutting the wire, exposing the monitor  o moisture, etc.;
2. Physical damages from cutting wires, scratching, dropping, hitting, etc.;
3. Components are opened;
4. Beyond the warranty period.

Wiring Diagram

1. Working Voltage: DC12V-36V
2. Make sure all plugs and cables connect correct, then power on
3. The standard configuration is an aviation connector.
4. The definition of aviation connector is as below:

Features

Monitor:

• 4 Channel AUDIO and VIDEO inputs.
• Auto-detect CVBS, 720P AHD, 960P AHD, or 1080P AHD video.
• Auto-switching between NTSC and PAL inputs.
• 1 to 4 Channel video monitoring using 1 to 4 screen display divisions.
• Built-in speaker with selected channel audio monitoring.
• 1 Channel CVBS video out to external monitor.
• 4 trigger inputs to trigger the monitor to display the corresponding camera in the full screen.
• Independent brightness, contrast, saturation, and sharpness adjust for each video channel.
• Independent on-screen display (OSD) for each camera – license plate number, driver name, etc.

DVR:

• Records in 720P or 1080P resolution at 30fps per channel.

• Recording modes: Continuous, Signal input triggered.

• Support SD storage to 256GB: estimated 384 hours or 16 days of continuous recording.

• On monitor playback or remove SD card and playback on a PC.
  Electrical:
  

• Circuit protection from under-voltage, over-voltage, overload, short-circuit, and reverse connection auto shutdown.
  Environmental:
  

• Operating temperature: -20C ~ 70C, max. humidity 95%

• Storage temperature: -30C ~ 80C, max. humidity 95%

Specification

Recording using)
Working Temperature| -20° C+70° C, Maximum humidity 95%
Storage Temperature| -30° C+80° C, Maximum humidity 95%
Operation Mode| 18# Remote control/Keystroke
Dimensions| 7inch 177(L)x141(W)x21(T)
9inch 228(L)x154(W)x27(T)

Keystroke

1.  Power Light
2. Light sensor
3. Power
4.  AV: UP/Down
5. Analog Decrease
6. Menu/Into Li)

| 7. Analog Inc
8. Singl
9. Dual
10. Quad
11. IR
12. SD Card Slot
---|---

Power on / off
AV Switch
Fast Backward
Up
Left /Analog decrease-
Previous
Exit / Turn Back
VOL
Power on / off| Fast Forward
ENT/Menu
Right /Analog increase+
Next 14 Down
Mute
Play / Pause
VOL+
Menu
---|---

Bracket installation

Can choose the bracket:
Headrest Frame; Plastic/Metal bracket; U-Bracket

1. B2 Installation

1. Use the screw to fix the U-bracket. Put the monitor into the bracket, adjust the angle and lock it.
   
2. Finished the installation. Adjust the angle forward 30° to backward 30°. Users can adjust a suitable angle by themselves.
   
   2. B 1/B2 Installation

1. Firstly fixed the bracket via the screws, the screws of the top need to lock to the nut under.

2. Secondly, put the metal buckle piece on the top of the fan-shaped bracket into the notch at the back of the monitor.

3. Move the bracket to the proper location. 4) Screw down the nut of the bracket, until the monitor fastens.

4. Screw down the nut of the bracket, until the monitor fastens. Menu

Remote control press the “ENT” button(Monitor press” M”button), the screen will show the OSD menu as below. Press “AV” cursor down/up, press “-” cursor left, press “+” cursor right; Press”MENU” to enter the option;

Record Query

Click “Record Query” to select the conditions for playback. The relevant Settings of: “Channel Selection”, “Audio Output” “Video Type”, “Search Date”, Start Time”, “Stop Time” and “Storage Device” are shown in the figure below:

1. Channel Select
   Press “ MENU ” to enter channel selection, press “AV ” to move up and down to select CH 1 to CH8 , and then press “MENU” to confirm playback. You can also select CHI to CH4 for multi-channel .playback. The system default channel is CH 1 -CH4

2. Sound Output
   Press “AV” to move up/down to select the Sound output, press “MENU” to enter, press “AV” to move up/down to select CH1 to CH4, and Press “MENU” to confirm that one of the channels is selected as sound output, and then replay the query selection. The corresponding channel will have a sound output, the system default is CH1.

3. Video Type
   Press “AV” to move up/down to select the type of video, and press “MENU” to enter, Press”AV” to move up/down to select, then press”MENU” to confirm the display. The system defaults to playback for all channels simultaneously.

4. Search Date
   Press”AV” to move up/down to select the Search date, and press”MENU” to enter, Press “-,+” and “AV” keys to select the date, year, month, and day that need to be checked, then press “MENU” to confirm. Default is the time of day.

5. Start Time
   Press “AV” to move up/down to select the Start time, and press “MENU”, press”-,+” to select the start time Hours, minutes, and seconds, then press “MENU” to confirm. Default is 00:00:00.

6. Stop Time
   Press “AV” to move up/down to select the End Time, and press “MENU” into, press “-,+” to select the end time Hours, minutes, and seconds, then press “MENU” to confirm. Default is 23:59:59.

7. Storage Device
   Press “AV” to move up/down to select the Storage device, and press”MENU” into it, press “AV” to select the storage device type, then press “MENU” to confirm. Default is a memory card.

Record Query

Video File Selection
After setting the query conditions, click “Query” to enter the list of video files, press “AV” to move up/down for selection, and Press”MENU” to confirm the selection files.
Playback preview
After selecting the file to be played, click “Play” to enter the playback preview, as shown below:

Record Set

Click “Video Set” can select video related configuration, as below:

1. Channel Select Press
   “MENU” enter, press “AV” to select All or B to CH4 channels, and press “MENU” to confirm.

2. Flame cut Delay
   Select the delay recording time after ACC is disconnected. Press “AV” to select the delay recording of flameout. You can select off, 5s,10s, 3min, 10min, 30min, 1 h, 2 h, 6 h, 12 h.

3. Record Time
   Press “AV” to move down to select the recording time, and press “AV” to select 3Min, 5Min, I °Min, 15Min, 20Min, 30Min, the default is 5Min.

4. Record Mode
   Press the “AV” button to move down, select recording mode, and press the “MENU” button to enter, you can choose to Shut down, Automatic, Scheduled, Alarm, Auto+alarm, or Plan-Farm. press the “ MENU” button to confirm, The default is automatic recording.

5. Image Flip
   Press “AV” to move down, select image flip, and press “ MENU” to enter, you can choose: normal, Horizontal and vertical, 90 and 270 degrees image flip, default “normal”

6. Encode Setting
   Pressing”AV” to select the video quality, press “MENU” to enter. Choice of channel, resolution (720P or 1080N ), image quality (poor, average, good, very good), and advanced Settings (frame rate, frame interval). Default resolution: 720P, Image quality: Very good. Picture as shown below:
   Record Set

7. Print Setting Press “AV” to select a print setting, press “MENU” into, All or CHI to CH4 single channel watermark can be set, Time watermark on/off, Car license plate watermark on/off, Channel watermark on/off, Location watermark on/off, Speed watermark on/off. Default channel watermark, time watermark, vehicle watermark on, position watermark off, speed watermark off, as shown in the figure below:

8. Audio
   Press “AV ” to select audio, and press “MENU” to enter the interface, you can choose to turn on / off audio, the default is” no “.
   Display
   Display Setting can set Display Adjustment, Channel Name, Loop Preview, Transparency, Installation Mode, Automatic Brightness, Time Display, and Display Mode.

Display Adjustment
Display adjustment includes “Scene Mode”, “Screen Margin” and “Channel Adjustment”. Press the “AV” key to select, and press the “ MENU ” key to enter: Scene mode:
In Scene Mode, you can select several default modes: Standard, Highlight, Film, Brilliance, Cool, Warm, Custom, and Default is Standard.
Screen Margin:
Screen margin can adjust the display screen, the screen zoom, horizontal position, and vertical position movement, Default is 0.

• Channel adjustment:
  Adjustable Brightness, Contrast, Saturation, Hue of all channels or each channel, The default channel is “all” and the parameter is “50”.

• Channel name:
  You can customize the display characters, press “AV” to select the channel name and press “MENU” to enter the channel name. Modify the setting interface, press “AV” to select channel CH1 to CH8, press “MENU” to pop up Enter the modified channel name on the soft keyboard and confirm it. Press “MENU” to save the Settings. Menu below:
  

• Loop preview:
  After the Loop preview setting, play the images in a loop sequence within the set time; Press “ MENU “, and then press “AV” to select off or 3S, 55, 8S, 105,155, and select any of them A time, in the preview interface channel screen will be displayed by the selected time automatically cycle switch. Default “off”.
  

• Transparency:
  Transparency can set the visibility of the menu; Press “MENU” into, then press “AV” to select 0%, 10%, 20%, 30%, 40%, 50%, Press “MENU” to confirm the effect, default is “0%”.

• Installation mode:
  Enter the menu to set: “Installation”, “Reversing Line” and “Reversing Priority”; Press “AV” to select, “MENU” to confirm, Menu below:

• Press”—, +” choose “Mode 1” or “Mode 2 “, and press “MENU” to confirm the effect. Default “Mode 1”.

• Backup line: press “-,+” to choose off or each CH. After choosing, the reverse line of the CH will be opened. I choose off, there will be no reverse line. Default “OFF”.

• Turn light mode: press “-, +” to choose each CH, the CH will be displayed when it is triggered. For example: Choose CH 1 and CH2, and CH 1 and CH2 will display on the screen when these two-channel are triggered. Default “off”.

• Backup priority line: press “-,+” to choose off each CH, the CH will be triggered first. For example, choose CH 1. Whenever CH 1 and other CH are triggered at the same time, CH 1 will be shown preferentially. Default “Off”

• Automatic Brightness:
  After being turned on, the screen brightness can be automatically adjusted according to, to the ambient brightness. Press “AV” to select on or off. Default “off’.

• Time Display:
  When off, the main page will not display the time. Press “AV” to select off or c Press the “MENU” button to confirm that the reboot device is effective. Default “

• Display Mode:
  Enter the menu to set: “back color”, “border-color”, “display mode”, press “AV” to select, and press “MENU” to select it, as shown in the picture below:
  Background color:
  press “-,+” key to select black or blue, and press the “MENt key to confirm. When there is no signal input, the background color is the selected color. the Default is “blue”.
  Border color :
  press “-,+” to select white, red, green, yellow, and press “MENU” key to confirm. When one of the colors is selected, the bord
  er line of the preview interface will be that color. Default is “white”.
  Display mode:
  press “-,+” key to select the display mode, and press “MENU to confirm, the ticked display mode will be displayed, not checked will no be displayed. For example, if the 9 partition mode is not checked, the 9 partition screen mode will not appear when the channel is displayed in the preview interface. Only the checked split mode will be displayed. The default is “select all”.
  Display
  Into “System Settings” to set “Language Selection” “Power Saving Mode” “System Time” “Vehicle Information” “User Management” “Storage Management”, “Restore Factory”, “System Upgrade” “System Information”
  System
  

• Language selection :
  Language selection: Simplified Chinese, Traditional Chinese, Korean, English. The default is English. Press “AV” to select and “MENU” to select.

• Power saving mode:
  After setting the power-saving mode, the screen will automatically close without any action, Can set OFF, 10Min, 30Min, lh, 2h. Default Off.

• System time :
  System time can be set: date, time, time format, daylight saving time, Press “AV” to select and “MENU” to confirm, MENU as below:

• Vehicle information
  Vehicle information can be set items: equipment number, terminal model, mobile phone number, license plate number, province ID, city ID, terminal ID, company name, service number, vehicle type, vehicle color, vehicle route, frame number, driver Driving license number, authentication code information, MENU as below:

• User managemen t
  Users can set relevant permissions and login passwords to manage or authorize Default Password of the”admin”is 12345

• Storage management:
  After connecting the storage device, the current state and formatting operation of the storage device can be viewed:

• Factory setting :
  Factory setting can restore the device to factory state:

• System upgrade :
  When the system has a new program, the “System Upgrade” can be updated to the best state.

• System information :
  All information related to the current system can be viewed, including the working status information of each module of the system: Hard disk information, GPS status, network information and serial port status.

References

• Get Warranty

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>