TAYLOR 1730 Wireless Indoor/Outdoor Thermometer and Clock with Remote Sensor Instruction Manual
- June 5, 2024
- TAYLOR
Table of Contents
TAYLOR 1730 Wireless Indoor/Outdoor Thermometer and Clock with Remote
Sensor Instruction Manual
INSTRUCTION MANUAL
Wireless Indoor/Outdoor Thermometer & Clock with Remote Sensor Model 1730
Simple, reliable, and accurate…the wireless thermometer & clock allows you to
monitor indoor or outdoor locations from one room. The base station reads
indoor conditions, while the remote sensor wirelessly reports outdoor weather
conditions back to the base station for an all-in-one weather display.
NOTE: Some stations have a static cling label over the digital display.
Please remove it before use.
BATTERY INFORMATION
IMPORTANT: Install batteries in the base station first, then the remote
sensor, otherwise the stations’ transmissions may not properly connect. Place
the base station as close as possible to the remote sensor when installing
batteries.
Base Station:
The base station operates on 2 AAA batteries (not included). The battery
compartment is located at the back of the station. Remove the battery
compartment door. Install (2) AAA size batteries into the battery compartment
according to the polarity markings. Replace the battery compartment door.
Remote Sensor:
The remote sensor operates on 2 AAA batteries (not included). The battery
compartment is located at the back of the station. Slide off the battery
compartment cover. Install (2) AAA size batteries into the battery compartment
according to the polarity markings. Replace the battery compartment door.
After Batteries are Installed:
When the stations are powered up, the LCD screen on the base station will
light up for 3 seconds, then the station will display initial indoor
temperature readings. The outdoor temperature display will show dashes “(–)”.
Press and hold the button on the front of the base station to activate the
paring to obtain outdoor temperature. A transmission signal icon (“ ”) flashes
by the “OUT” temperature digits during this time. When the “ ” icon turns off,
the base station has connected with the remote and starts reporting the
current outdoor temperature.
For best setup connection, keep the base station and remote close to each
other while trying to connect. Keep away from other electronic equipment that
may interfere with the connections, such as mobile phones, appliances,
computers, refrigerators, TVs, etc.
Indoor temperature readings update on the base station approximately every 30
seconds. The remote sensor transmits outdoor temperature readings to the base
station approximately every 57 seconds. A red light flashes on the sensor when
it sends a transmission signal.
NOTE: While the base station is in “analyzing” mode, some functions (such
as Clock Setting) may not be operational, or using the functions will
interrupt the transmission reception. Once the “analyzing” mode is complete,
the other functions will become operational.
LOW BATTERY
Base Station : Replace the batteries if readings grow dim or irregular.
Remote Sensor: Replace the batteries if the red light on the sensor stops
flashing approximately every 57 seconds, or if transmission signals seem weak
or irregular.
IMPORTANT: Always replace both batteries at the same time; do not mix old
and new batteries. Do not mix alkaline, standard (carbon-zinc), or
rechargeable (ni-cad, ni-mh, etc.) batteries.
TIP: When the temperature falls below freezing point, alkaline batteries
used in outdoor stations may freeze, lowering their voltage supply and
effective range. Use of Lithium batteries is recommended in extremely cold or
hot locations.
WARNING: Batteries may pose a choking hazard. As with all small items, do
not let children handle batteries. If swallowed, seek medical attention
immediately.
PRECAUTION: Do not dispose of batteries in a fire. Batteries may explode
or leak. Remove the batteries if the stations will not be used for a long
period of time.
NOTE: Please recycle or dispose of batteries per local regulations.
DISPLAYING THE WEATHER STATION
Base Station:
Pull out the bottom of the table stand located on the back of the base station
to set it on a flat surface.
Place the base station indoors in a well-ventilated location away from direct
sunlight.
Remote Sensor:
Table top – pull out a stand to place the sensor on a flat surface. Wall – use
the keyhole on the back of the remote to hang on a wall with a nail or screw
(not included).
The transmission range of the remote sensor is 200 feet. The effective
transmission range is vastly affected by obstacles such as walls, sheds,
trees, etc. Try various setups for the best results. Shorten the distance
between the base and remote stations when necessary.
To get the most accurate readings and to prolong the life of your sensor, we
recommend that you mount it out of direct sunlight and rain. Direct sunlight
will heat the casing and inflate temperature readings. Place the sensor in a
dry, shaded area. Fog and mist will not affect the sensor, but large volumes
of soaking rain may. To guard against this, we recommend that you mount it
under the eve of your house, your garage, or any other suitable place that
will keep it out of direct sun and rain.
IMPORTANT: Though the remote station is weather-resistant, it should be
placed away from direct sunlight, rain, and snow and should never be submerged
in water.
TEMPERATURE READINGS
Press the “°F/°C” button on the back of the base station to switch between
Fahrenheit and Celsius temperature displays.
The base station displays the indoor temperature (“IN”) from its location. The
remote station transmits outdoor temperature (“OUT”) from its location back to
the base station.
The indoor and outdoor temperature readings will display in either the large
display window in the center of the screen or the small window at the bottom
left of the screen. Press the “ ” button on the front of the thermometer to
switch indoor/outdoor temperature readings between the larger and smaller
display windows. An “IN” or “OUT” icon next to the temperature digits
indicates which temperature location is displayed in the window.
CLOCK SETTING
The Clock display is located in the bottom right of the LCD screen.
- Press and hold the “SET” button on the back of the base station for 3 seconds to enter Clock Setting Mode. “12 Hr.” or “24 Hr.” flashes in place of the clock digits.
- Press the “+” button on the back of the base station to toggle between 12 or 24-hour clock mode. Press “SET” to confirm. The hour digits’ flash.
- Press the “+” button to change the hours. Press “SET” to confirm. The minute digits’ flash.
- Press the “+” button to change the minutes. Press “SET” to confirm. The hour and minute digits stop flashing. The clock is set.
NOTE: If no buttons are pressed within 30 seconds, the station will
automatically exit Clock Setting mode.
Until a time has been set, the clock will count up the time since battery
installation.
MAXIMUM/MINIMUM TEMPERATURE MEMORY RECALL
The thermometer will store the last recorded high and low temperatures over a
24-hour period.
The 24-hour period starts when the stations are powered up.
- Press the “MEM” button on the back of the base station once to display the maximum indoor and outdoor temperature readings since the station was last reset. “MAX” will show on the LCD.
- Press the “MEM” button a second time to display the minimum indoor and outdoor temperature readings since the station was last reset. “MIN” will show on the LCD.
- Press the “MEM” button a third time to see current indoor and outdoor temperatures, or the display will automatically return to current readings after 5 seconds.
To clear the maximum and minimum readings: press and hold the “MEM” button for 3 seconds to clear both memories. The temperature displays show dashes (“–”) and the station will begin to track new MAX and MIN readings. The memories will also reset when the station’s batteries are removed.
PROBLEM SOLVING
-
If the base station does not receive a transmission from the remote sensor for one hour, the outdoor temperature display will show dashes (“- -”). Press and hold the “ ” button on the front of the base station for 3 seconds to force a transmission signal. If the connection still fails:
a. Check that the remote is properly positioned, within the appropriate transmission range (200 feet). Transmissions are vastly affected by building materials and where the receiver and remote stations are positioned. Try various setups for the best results. Shorten the distance between receiver and remote stations when necessary.
b. Check to make sure the transmission path is clear of obstacles and interference.
c. Place the remote sensor closer to the base station.
d. Remove and reinstall all batteries. Try fresh batteries. -
If the temperature is higher than the range of the station, the display will show “HH.H”.
If the temperature is lower, this display will show “LL.L”.
a. Indoor temperature range is 32°F to 122°F (0°C to 50°C).
b. Outdoor temperature range transmitted by the remote sensor is -4°F to 140°F (20°C to 60°C) using alkaline batteries. (Use of Lithium batteries can extend the range from -40°F to 140°F / -40°C to 60°C.) -
The temperature sensors are manufactured to be accurate within plus or minus 2°F (1°C) within a temperature range from 32 to 104°F (0 to 40°C) and plus or minus 4°F (2°C) outside that range. Therefore, 2 stations placed next to each other may report different readings. This is a normal occurrence with digital sensors and should not be considered a defect.
-
For maximum performance in normal conditions, good quality alkaline batteries are recommended. When temperatures are below 0°F, alkaline batteries can lose power resulting in a loss of remote transmission. If you reside in an area that experiences frequent temperatures near or below 0°F, lithium batteries are recommended to minimize the loss of transmission.
TRANSMISSION COLLISION
Signals from other household devices, such as doorbells, home security
systems, and entry controls, may interfere. This is normal and does not affect
the general performance of this product. The transmission will resume once the
interference recedes.
PRECAUTIONS
-
The base station is intended for indoor use only. It is not sealed against moisture and could be damaged if used outdoors. The remote sensor is weather-resistant but not
weather-proof or waterproof. Do not immerse it in water or allow snow to accumulate on it. Do not leave it outdoors in extreme weather conditions. If these conditions become likely to occur, temporarily move the sensor to an indoor area. Otherwise, permanent damage to the sensor’s internal circuits may occur. -
Do not immerse the stations in water. If you spill liquid on one, dry immediately with a soft, lint-free cloth.
-
Do not clean the stations with abrasive or corrosive materials. This may scratch plastic parts and corrode electronic circuits.
-
Do not subject stations to excessive force, shock, dust, temperature, or humidity. This may result in malfunction, shorter electronic life span, damaged batteries, or distorted parts.
-
Do not tamper with the station’s internal components. Doing so will invalidate the warranty on this product and may cause damage. The stations contain no user-serviceable parts.
-
Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc.) batteries. Do not dispose of batteries in a fire. Batteries
may explode or leak. Remove the batteries if the stations will not be used for a long period of time. -
This product is for measuring weather temperatures only. DO NOT PLACE STATIONS INTO OVENS, GRILLS, FREEZERS, or MICROWAVE OVENS.
-
Always read the instruction manual before operating this product.
SPECIFICATIONS
Indoor temperature range: 32°F to 122°F (0°C to 50°C) Outdoor temperature range transmitted by remote sensor: Alkaline batteries: -4°F to 140°F (-20°C to 60°C) Lithium batteries: -40°F to 140°F (-40°C to 60°C) Resolution: 0.1 degrees for temperature Indoor temperature readings update approximately every 30 seconds Remote sensor transmits temperature readings every 57 seconds. Minimum/Maximum temperature records 12/24-hour clock Transmission: Maximum 200 feet (60 meters) in open area Power: 2 AAA batteries (not included) for base station and 2 AAA batteries for remote sensor (not included)
Party issuing Supplier’s Declaration of Conformity &
Responsible party – U.S. Contact information:
Taylor Precision Products
2311 W. 22nd Street, Suite 200
Oak Brook, IL 60523
Equipment:
Product Name: Wireless Indoor/Outdoor Thermometer & Clock with Remote Sensor
Model No.: 5293168
Trade Name: Taylor, a division of Lifetime Brands, Inc.
Caution: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Note: This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. This equipment has
been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning:
Federal Communications Commission (FCC) Statement. This device complies with
part 15 of the
FCC Rules. Operation is subject to the following conditions:
This device may not cause harmful interference, and this device must accept
any interference received, including interference that may cause undesired
operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications made to this device not expressly
approved by FUZHOU SUNNY ELECTRONIC CO., LTD may void the FCC authorization to
operate this device.
Note: The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment. Such modifications
could void the user’s authority to operate the equipment.
RF exposure statement:
This device complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. The device is installed and operated without
restriction.
FCC ID: 2ACW8-GP1730
FAQS
How long do the batteries last?
We have several of these in various areas and have no problem with the batteries on the inside or outside units. They last a very long time. We change them so infrequently, it is definitely not an issue.
Can you use multiple units in the same area? Considering using these to monitor actual room temps in a conference center.
Yes, you can have multiple units in the same area because the unit and the sensor coincide with each other during set up.
Can the main unit be wall mounted?
The display unit has no provision for wall mounting. The sensor unit does.
Is the display illuminated?
The display is not illuminated
What is the temperature range for this unit?
copied from the taylorusa dot com site
Outdoor temperature range:
Alkaline batteries: -4°F/140°F and -20°C/60°C
Lithium batteries: -40°F/140°F and -40°C/60°C
Which says something about battery function in the cold weather.
What is the range? how far away can i place the receiver? i want to put the sensor into my bee hive and read the temp from in the house
Greetings from Filament Brands! Thank you for your interest in the Taylor Wireless Digital Indoor/Outdoor Thermometer.
where is the product made?
Package states” Made to our exact specifications in China.”
how do I install batteries?
BATTERY INSTALLATION
The base unit operates on 2 AA batteries (not included).
The remote sensor operates on 2 AAA batteries (not included).
Replace the batteries if readings grow dim or irregular. Always replace both
batteries at the same time; do not mix old and
new batteries. Do not mix alkaline, standard (carbon-zinc) or rechargeable
(ni-cad, ni-mh, etc.) batteries.
IMPORTANT: Power the base unit first, and then the remote sensor, otherwise
the units’ transmissions may not properly
connect. Place the base unit as close as possible to the remote sensor during
set up.
TIP: When the temperature falls below freezing point, alkaline batteries used
in outdoor units may freeze, lowering their
voltage supply and effective range. Use of Lithium batteries is recommended in
extremely cold or hot locations.
Base Unit
Battery Power: The battery compartment is located on the back of the unit.
Remove the battery compartment door. Install
(2) AA size batteries into the battery compartment according to the polarity
markings. Replace the battery compartment
door.
Remote Sensor
The battery compartment is located on the back of the unit. Remove the battery
compartment cover. Install (2) AAA size
batteries into the battery compartment according to the polarity markings.
Replace the battery compartment door.
Is it possible to buy just the sending unit?
Don’t think you can, but it is such an inexpensive item, I would just buy a new one and save the old in case you need it in the future.
Does it really take 1 to 2 months to ship?
No, we fulfill and ship out this item around 1-3 days, you should receive your order around 7 – 10 days
What size batteries does it take?
This product requires 2 AAA batteries for the base station and 2 AAA batteries for the remote
does this work with wi-fi?
No, it is a very basic unit.
Can you read it very well in the evening, near a lamp while watching TV?
You will be able to read this near a lamp with other lighting in the background. You may need to reposition it some of you can’t based on a reflection but should be able to find the right angle
How does the remote attach?
Remote sensor
Table top – place the sensor on a flat surface.
Wall – use the keyhole on the back of the remote to hang on a wall using a
nail or screw (not included).
Why does outside temp register ad LL.L?
the battery on the white unit is not working or both need to be turned off for 30 seconds to reset. Your outside white unit may not be facing the black receiver. Good Luck!
What are the dimensions of each piece? There seems to be a great variance in the answers given.
The indoor unit is 9cm X 6cm or 3.5″ X 2.25 “. The outdoor unit is about 9cm X 3cm or 3.5 ” X 1.25 “. I have two and they are both the same.
VIDEO
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>