PORTOS DC15 Drive Controlling System User Manual
- June 5, 2024
- PORTOS
Table of Contents
PORTOS drive controlling system
USER MANUAL
DC1, DC15
**** The remotes operate at 433 MHz frequency
Technical data :
Power:
Operating frequency:
Transmission power:
Operating temperature:
Operating range:| 3V battery ( CR 2430 )
433 MHz
10 mW
from -10 ˚C to +50 ˚C
Determined by architectural
and regulatory factors
---|---
Device characteristics:
DC1 (1 channel)
DC15 (15 channels)
- Programming the radio drive on a specific channel of any transmitter.
A. Method one
IMPORTANT!!!
While programming, only the drive being programmed should be connected to a
power supply. After connecting the motor to a power supply, you will hear a
long single beep sound and the motor will move briefly up and down (if you do
not press any button within 12 seconds, the motor will quit the programming
mode).
- Using the CHANNEL + / – buttons, select the channel you wish to program:
- Press the P2 button, the motor will make a single beep sound.
- Press P2 again, and the motor will make a single beep sound again.
- Press the UP button, the motor will make 6 beeps and move briefly up and down, which means that the channel has been programmed.
B. Method two
In order to program the drive, open the inspection hatch of the roller shutter
and:
-
Press the microswitch located on the lead emerging from the head of the drive for 1 second – the motor will confirm with a single beep sound and the shutter will move
briefly UP and DOWN. -
Using the CHANNEL + / – buttons, select the channel you want to program and press P2 – the motor will make a single beep sound.
-
Press P2 again, the motor will make a single beep sound again.
-
To finish the programming process, press UP. You will hear 6 beeps and the roller shutter will move briefly up and down.
IMPORTANT!!!
If you have an external radio receiver, follow the user manual for the device
(i.e. XT-R, PPKR-313, or PPKR-400).
3. Changing the direction of rotation of the drive.
METHOD 1:
After assigning the device to a motor, check if the running direction is
correct by switching the motor on with the device. To change the running
direction of the motor, you need to reprogram the channel (point 1 of this
manual) by changing the programming method – if the motor was programmed
following the P2 + P2 + UP method and the direction of rotation needs
reversing, reprogram the motor by finishing the programming process with
direction reversal, i.e. P2 + P2 + DOWN. The drive will register the direction
change.
METHOD 2:
Using the microswitch located on the lead emerging from the head of the drive,
you can change the drive’s running direction. To do so, you should:
- Press the microswitch down for 6 seconds.
- After 1 second, the motor will confirm with a short beep sound and move up and down, whereas after the next 5 seconds the motor will confirm the direction change with 3 beeps and the roller shutter will move UP and DOWN twice.
4. Channel deletion (deleting all channel settings).
IMPORTANT!!!
If you delete the settings of a particular channel, drives assigned to that
channel will be completely deleted from other channels as well.
METHOD 1:
- Select a previously programmed channel on the display:
- Press P2, the motor will make a single beep sound and move briefly up and down.
- Press STOP, the motor will make a single beep sound.
- Press P2 again, you will hear 4 beeps and the roller shutter will move briefly up and down.
METHOD 2:
Using the microswitch located on the lead emerging from the head of the drive,
you can delete a previously programmed transmitter channel. To do so, you
should:
- Press the microswitch down for at least 15 seconds.
- After 1 second, the motor will make a short beep sound and move up and down, whereas after the next 5 seconds, the motor will confirm with 3 beeps and the roller shutter will move UP and DOWN twice, and finally after 15 seconds the motor will make 3 beeps and the roller shutter will move UP and DOWN once.
METHOD 3:
Reprogramming the radio drive on a given channel (point 1 of this manual)
automatically deletes previous settings.
5. Adding another channel (transmitter) to the motor.
To add another channel or another device, start with the transmitter which was programmed first. While adding an additional transmitter (channel), do not disconnect the motor from power supply! Transmitters must be located within the receivers’ range.
- Select a previously programmed channel on the display of the active transmitter.
- Press P2, the motor will make a single beep sound and move briefly up and down.
- Press P2 again, the motor will make a single beep sound again.
- Press P2 on the device you wish to program. You will hear 5 beeps and the motor will move briefly UP and DOWN.
6. Device operating mode.
The PORTOS-RM radio drive can operate in two modes: Support mode
Pressing and releasing the UP or DOWN button activates a programmed motor
function (opening or closing the roller shutter). The motor will operate until
the roller shutter is fully opened or closed.
Non-support mode
The motor will only operate when the button is pressed down. Releasing the
button stops the motor. If the button is pressed down for more than 2 seconds,
the motor will start operating in the support mode, i.e. until the roller
shutter is fully opened or closed.
7. Changing the operating mode.
You can switch between the operating modes by following the instructions below:
- Select a previously programmed channel.
- Press P2, the motor will make a single beep sound and move briefly UP and DOWN.
- Press UP, the motor will make a single beep sound.
- Press P2, you will hear 3 beeps and the motor will move briefly UP and DOWN.
The remote operating mode change is complete. It affects all channels and remotes assigned later.
To deactivate unused channels we do as follows:
- Press CHANNEL – and CHANNEL + buttons simultaneously.
- The C will appear on the display.
- Press and hold the CHANNEL – and CHANNEL + buttons again.
- The number of currently activated channels will appear on the display.
- Use CHANNEL – and CHANNEL + buttons to select the number of channels to be used.
- Press the STOP button to confirm.
NOTES
PORTOS TR7
spotka z ograniczong odpowiedzialno6cia spolka komandytowa
ul. Ziota 71
62 – 800 Kalisz
tel. 62 / 768 40 00
sekretariat@portosrolety.pl
www.portosrolety.pl
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>