OUTDOOR TECH OT5901 Hawk Bone Conduction Sport Headphones Instruction Manual
- September 25, 2024
- OUTDOOR TECH
Table of Contents
OUTDOOR TECH OT5901 Hawk Bone Conduction Sport Headphones
How to wear
Package Included
Button Description
Dual Listening/Open-ear Design
Listen to the world around you simultaneously.
Specification
- Model: OT5901
- Type: Open-Ear Sports Headphones
- BT Version: BK3266 5.0 EDR
- Frequency Range: 20-20kHz
- Connection: 10 Meters
- Microphone: -42db
- Battery Capacity: 230mAh Polymer Battery
- Play Time: ≥5 Hours(80% Volume)
- Standby Time: ≈220 Hours
- Charging Time: ≈2 Hours
Power On
- Press and hold the power button for 3 sec.
- White & green LED flash.
- Prompt: power on pairing.
Connect BT
Turn on the BT menu and search “ODT HAWK”, and click to connect. Prompt:
connected.
Power Off
- Press and hold the power button for 3 sec.
- White LED blinks. Prompt: power off.
Answer A Call
Click the MFB once.
End A Call
Click the MFB once.
Reject A Call
Double-click the MFB .
Previous Song
Press and hold button +
Next Song
Press and hold button –
Play/Pause Music
Click the MFB once.
Volume Up
Click the button + once.
Volume Down
Click the button – once.
Activate Voice Assistant
Press and hold the MFB to activate the phone’s voice assistant.
Restore Factory Setting
Under power-off mode, press and hold the power button for 10 sec.
Low Battery
Green LED flashes every 30 sec when the battery is lower than 10%. Prompt: low
battery.
Charging
Please use a DC 5V adapter for charging. The green LED is on when charging.
White LED is on when fully charged.
Attention
- Listening to loud music for a long time may cause discomfort, please use medium volume if possible. Do not use high volume for long periods.
- Using headphones will affect your perception of the surrounding environment. Pay more attention when using headphones.
- Do not remove or modify the headphones, as this may cause damage or burnout.
- Do not throw, sit on headphones, or immerse them in water.
- Keep it away from fire, water, and high-pressure equipment.
- Not suitable for children under 3 years old and containing small parts.
- Do not classify it as household waste. please send it to the local electrical equipment recycling station;
Note:
The company does not assume any responsibility for the loss of personal
property caused by the violation of the above warnings.
If you have any questions about HAWK please reach out to support@outdoortech.com for help.
WARNING:
This product can expose you to chemicals that are known to the State of
California to cause cancer. For more information go to
www.P65Warnings.ca.gov.
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.