boAt Airdopes 131 Captain America Marvel Edition TWS Earbuds User Manual
- June 5, 2024
- Boat
Table of Contents
Airdopes 131 Captain America Marvel Edition TWS Earbuds
User Manual
Walkthrough Video
Specifications
Buttons and Indicators
Troubleshooting FAQs
Charging
How can I charge the case?
Step 1: To charge the case, plug one end of the charging cable into the
case and the other end into a USB port/adapter.
Step 2: Flashing white LEDs indicate that the charging case is being
charged. Once the charging case gets fully charged, the LEDs turn into solid
white.
How to charge the earbuds?
1. To charge the earbuds, put the earbuds into the charging case in their
correct orientation.
2. A solid White LED will indicate that the earbuds are being charged.
3. Once fully charged, the LED indicator goes off.
Note: Before using the earbuds for the first time, it is recommended to fully charge the earbuds. Also, please keep the lid of the charging case closed. While charging and use a 5V/2A adaptor.
What to do if charging case is not charging?
1. Check if the stickers on the charging points of the ear pods are removed
or not. If not then it is to be removed and the ear pods will start charging
once put inside the charging case.
2. Check if the charging cable connected to the case is not broken, use other
charging cable and also ensure that the charger being used is not of 9V or 12V
as that will damage the case. The LED lights located on the charging case
indicate the battery status of the case.
What to do if earbuds are not charging?
1. Ensure that the earphone case is charged for charging the earbuds
2. Check to see if the earbuds have been put inside the case in the right
orientation, and a white light on the earbuds will indicate they are still
being charged. This light will go off once the earbud’s have been completely
charged.
3. Clean the magnetic connector pins on the case and connector place on the
earbuds with a clean cloth with mild alcohol and check the charging of the
earbuds again
4. After cleaning, put the left earbud into the case in desired orientation
and close the lid.
5. After cleaning, put the right earbud into the case in desired orientation
and close the lid.
6. Once both the earbuds are charged, the LED on the case will go off.
What to do if earbuds not charging while inside the charging case even
when the case is charged?
1. Check if the charging pins of the case are clear and there is no
obstruction
2. Check if the charging pin of the earbuds are clear and there is no
obstruction.
3. Check if the orientation of the earbuds inside the case is correct and
they have been properly inserted inside the case.
4. Check if the pogo pins are clean. You may do so by gently cleaning it
cotton swabs with alcohol.
Device Controls
How to Power ON/OFF Airdopes 131?
1. Power ON:
Step 1: To switch the earbuds on (Smart Power On) simply open the lid of the
charging case (when earbuds are inside). Our IWP™ (Insta Wake N’ Pair)
Technology enables the earbuds to power on automatically, get connected and
enter into the connection mode. OR Long touch the CTC on both earbuds for 3
seconds to manually power on the earbuds.
Step 2: Both the earbuds will automatically pair with each other. The earbuds
will enter into the Connection Mode. Once the earbuds are powered on Red and
Blue LED will indicate the same.
2. Power OFF:
Smart Power Off:
Step1: After usage, remove both the earbuds from your ears.
Step2: Place the earbuds back into the charging case in correct orientation.
Step3: The earbuds will automatically switch off (and enter into charging
mode).
Manual Power Off:
Step1: Long touch the CTC on both earbud for 8 seconds to manually power off
the earbuds.
Step2: Once the earbuds get turned off, place them back inside the case and
close the lid.
How Do I factory reset my earbud?
In order to factory reset Airdopes 131, go to the Bluetooth settings on your
mobile device, find Airdopes 131 and select ‘forget’. On your Airdopes 131,
Step 1: Keep both the earbuds inside the case in their correct orientation
Step 2: Triple tap the MFB on both earbuds to perform the reset. Red LED
blinks for 1 sec to indicate the same.
Step 3: After the reset, close the lid of the carry case.
Below are the cases where factory reset may be helpful
- One earbud is not working
- Earbuds are not getting connected or scanned
- Earbuds gets disconnected during a phone call
- If there are exceptions in usage
How can I activate Voice Assistant?
Long press the MFB on either earbud for 2 seconds to activate the voice
assistant
How to Answer/Hang Up Call through Airdopes 131?
Single press the MFB on either earbud to answer an incoming call and once
again to hang up an ongoing call
How do I Reject a call through Airdopes 131?
Long press the MFB for 2 seconds to reject incoming calls.
How to Play/Pause Music through Airdopes 131?
Single press the MFB on either earbud to play a song or to pause one.
How to change music tracks in Airdopes 131?
1. When playing music, double press the right earbud’s MFB in order to skip
to the next song on the playlist.
2. When playing music, double press the left earbud’s MFB in order to return
to the previous song on the playlist.
Note: Volume cannot be controlled via earbuds and can only be adjusted via phone/media device.
How can I use a single earbud at a time?
Step 1: Please note that both the earbuds can be used in mono mode. Use either
of the two options; Smart Power On or Manual Power On for switching on the
desired earbud.
Step 2: The selected earbud will automatically enter the connection mode.
Step 3: Turn on Bluetooth on your phone/media device and search for ‘Airdopes-
131’ to connect.
Notes: To switch to Stereo mode, simply take out the other earbud from the case. It will automatically power on and pair with the previously selected earbud, hence enabling Stereo usage.You cannot skip tracks or return to the previous tracks in Mono mod
Poor Sound Quality
What to do if the sound is distorted/low volume/low bass/low quality?
1. Check if connected device does not have any equalizer settings applied.
2. Check if the problem still occurs if the device is moved closer and all
obstacles in the middle are removed.
3. Check if the distortion or quality lowers at all volumes or only at high
volumes.
4. Check the sound on different media players and different devices and if
the distortion happens on all devices or only on specific ones.
5. Check if the problem occurs at all levels of charging or only at low
charging levels.
6. Check if the earbuds do not have water droplets, in case they do, use the
blow dryer to dry out any water from a distance.
7. Check if the earbuds are clogged with ear wax, simply clear the earbuds to
restore the original sound.
What to do if the sound output is muffled?
1. Check if connected device does not have any equalizer settings applied.
2. Check if the problem still occurs if the device is moved closer and all
obstacles in the middle are removed.
3. Check if the distortion or quality lowers at all volumes or only at high
volumes.
4. Check the sound on different media players and different devices and if
the distortion happens on all devices or only on specific ones.
5. Check if the problem occurs at all levels of charging or only at low
charging levels.
6. Check if the earbuds do not have water droplets, in case they do, use the
blow dryer to dry out any water from a distance.
7. Check if the earbuds are clogged with ear wax, simply clear the earbuds to
restore the original sound.
Bluetooth Connectivity
What to do if device not connecting via Bluetooth?
1. Check if the device is in pairing mode and indicating that by alternating
green and red LED flashes on either earbud.
2. Check if the device is in the range of Bluetooth (usually 10m) and if
there are any obstructions in between.
3. Check if the device being connected to supports Bluetooth connections or
not.
4. Check if it is a passcode issue and if so enter 0000 / 1234.
5. Check if the device being connected to does have any software issues or
not – Check to forget the device on Bluetooth, update the mobile software, if
it still does not work try factory resetting the device.
What to do if device not entering stereo mode / stuck in mono?
1. Check when both the earbuds are taken out of the charging case, the
earbuds will enter into the Connection Mode, indicated by light blue LED
flashes.
2. If one of them fails to smart power on, to manually switch the earbuds on
(Manual Power On), long touch the CTC for 3 seconds on both Left and Right
earbuds for switching them on until the LED light begins to flash in red and
white colours.
3. Place the earbuds in the charging case and then try using them again.
Check if it connects automatically.
4. Check and see if hard resetting the device work as desired or not.
5. Check if the earbuds are charging or not. If not then clean the earbuds
and the charging case specially the charging pins and connectors with mild
alcohol swab and see if it goes in charging mode or not.
What to do if device occasionally disconnects/ the right earbud keeps
disconnecting?
1. Check if restarting the device resolves the issue.
2. Check if the same problem happens for different devices and media players.
3. Check if there are any obstructions between the earbuds and the device and
clear them, move the device at a closer range to the earbuds and see if it
still affects it.
4. Try factory-resetting the device.
Why one side of my earbud not working?
Dysfunctional Voice Assistant
What to do if the voice assistant does not wake up?
Check if the pairing device has the feature enabled. Google Assistant or Siri
should be enabled to use this feature from your device.
Please follow the steps carefully, long touch the CTC for 2 seconds and release, this should allow Google Assistant or Siri to pop up on the media screen of the device. Though under some circumstance, this feature may or may not work on some devices which may be restricted by default.
Product Functionality
What to do if device does not turn on?
1. Check to see if the device has been properly charged first or not. A blue
light on the earbuds will indicate they are still being charged. This light
will go off once the earbud’s have been completely charged.
2. Check if the voltage of the charger is correct for the charging case and
if the lights on the bottom are glowing to indicate the charge level.
3. Check by switching the earbuds on manually, press and hold the capacitive
touch control for 2 seconds until the LED begins to flash in blue.
4. Check if the device was not subject to any mishandling, broken wires or
exposed to direct sunlight or hazards like fire.
5. Check if the charging pins of the case and earbuds have some dirt
accumulation or corrosion and clean them with alcohol swab and then put them
back in the case for charge and the earbuds should start charging.
What to do if the in-built controls (CTC) of the device are not working?
1. Check if the controls do not work while connected to another device.
2. Check if the media player being used supports such controls and if the
controls do not function on call or other media players
3. Check if the controls have been physically damaged or exposed to any
hazards.
4. Check if the control area has some sweat and oil as that might interfere
with the capacitive touch control and clean the control area to remove any oil
or sweat and the touch control should start working.
Instant Pairing
What to do if Insta Wake & Pair (IWP) is not working for my Airdopes?
1. Make sure that you have paired the Airdopes at least once to the device
you are trying to use IWP with before.
2. Check if Bluetooth is turned on for your media device and it has the
Airdopes in the list of paired devices.
3. Try factory-resetting the device.
4. Check if your Airdopes battery case has battery in it to have IWP
functioning.
Microphone Functionality
What to do if voice is muffled during calls/ Microphone has muffled
input?
1. Check if restarting the device resolves the issue.
2. Check if dust or ear wax as accumulated near or inside the microphone
port, there is no blockage on the microphone.
3. Check if sweat or water has gone inside the microphone.
4. Check if there are any obstructions between the earbuds and the device and
clear them, move the device at a closer range to the earbuds and see if it
still affects it.
What to do if any problem related to any functionality occurs in
Airdopes?
1. Check if restarting the device resolves the issue.
2. Place the earbud’s in the charging case and then try using them again.
3. Try factory-resetting the device.
General FAQs
Product Functionality
What is Insta Wake N’ Pair (IWP) technology?
1. Our IWP technology allows the earbuds to connect to your phone, if they
have already been paired before instantaneously upon opening the case.
2. Simply open the case and ensure that the Bluetooth is turned on for your
media device, the buds will connect as soon as the case is opened without the
need to take them out of the case first.
How to enable IWP for my earbuds?
There is no special process to enable IWP, simply follow the steps to pair
your Airdopes to your media device first, then upon subsequent usage the IWP
tech will be enabled automatically and the Airdopes will pair automatically to
your previously paired media device if Bluetooth is turned on your media
device.
Does the Airdopes 131 support aptX codec by Qualcomm?
No. Airdopes 131 does not support aptX codec by Qualcomm.
Does my Airdopes 131 have CVC technology by Qualcomm?
No. Airdopes 131 does not support CVC technology.
Does my device have dual microphone?
No. Airdopes 131 does not have dual microphone.
Can the volume of the earbuds be controlled through integrated controls?
No. The volume cannot be controlled via earbuds and can only be adjusted via
phone/media device.