NICO Robot vacuum cleaner 2 in 1 with smart application User Manual

NICO Robot vacuum cleaner 2 in 1 with smart application

 GENERAL SAFETY INSTRUCTIONS

• Consider the instructions for use as a part of the appliance and pass them on to any other user of the appliance.
• Check whether the data on the type label correspond with the voltage in electric socket.
•  Never use the appliance if its power cord of adaptor is damaged, if it does not work properly, if it fell down and was damaged. In this case take the appliance to a special service to check its safety and proper function.
• The product is intended for home use and similar (in shops, offices and similar workplaces, in hotels, motels and other residential environments, in facilities providing accommodation with breakfast). It is not intended for commercial use!
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
•  Before replacing accessories or accessible parts, which move during operation, before assembly and disassembly, before cleaning or maintenance, turn off the appliance!
•  If the power cord of the adaptor is corrupted, it has to be replaced by the manufacturer, its service technician or a similarly qualified person so as to prevent dangerous situations.
•  Never use the appliance if its adaptor or plug is damaged, if it does not work properly, if it fell down and was damaged or if it fell to water. In this case take the appliance to a special service to check its safety and proper function.
•  In order to ensure safety and proper function of the appliance, use only original spare parts and accessories approved by the manufacturer.
•  If the adaptor of the appliance is corrupted, it has to be replaced by the manufacturer, its service technician or a similarly qualified person so as to prevent dangerous situations.
•   WARNING: To charge the battery, use only the network adapter supplied with this appliance.
• To power the appliance, only apply safe small voltage in accordance with the type plate.
• Don´t put hands close to rotating part.
• Never immerse the vacuum cleaner into water (even its parts)!
•  Never vacuum without a properly inserted filtration system and micro-filters.
•  Do not vacuum sharp objects (e.g. glass, shatter), hot, flammable, explosive items (e.g. ash, hot cigarette butts, gasoline, thinners and aerosol vapours) or greases (e.g. fats, oils), caustic agents (e.g. acids, solvents). Vacuuming these objects may lead to damage of the dust filters, or the vacuum cleaner.
• Pores of the filters may be clogged when vacuum cleaning very fine dust (e.g. fine sand, cement dust, plaster). Thus, air permeability will be reduced and the suction performance will drop. In this case, clean the filters even though the dust container is not full yet.
•  Always switch off the vacuum cleaner first and disconnect the power cord from power supply and only then empty the dust container, clean/replace micro-filters, clean the vacuum cleaner or its accessories.
•  Never leave the vacuum cleaner exposed to weather conditions (rain, frost, direct sun radiation, etc.).
• Never use the appliance for any other purpose than for the intended purpose described in these instructions for use!
•  Disconnect the appliance from the mains when not in use for a long period.
• Secure please gaps on the floor (eg, Threshold Strip) to avoid damaging the rotating brushes. These joints may also limit the vacuum cleaner jams bristle of brush into the gaps.
• This device can not be used on a carpet whose pile length is over 1 cm. At the same time, the vacuum cleaner may not function properly on some types of dark carpets which surface „deceives” the sensors an can cause chaotic movements of the vacuum cleaner or its failure to reach some parts of the floor.
•  The robot vacuum can go over threshold strips up to 1,5 cm in height.
•  Remove the battery when the vacuum cleaner is not in use.
•  Make precautions to solve the problem which may make the cleaning in trouble, such as:
  • Keep the easily knock over objects in a safe place.
  • Permian the edge of the carpet.
  • The hanging table cloth and curtain should not touch the ground.
  •  The flammable object should be cut from the fire source.
  •  Sort out the tangled power cord on the floor.
  •  Pick up the newspaper, book, magazine and large piece of paper scattered on the floor.
• Check whether the main brush is correctly fixed inside the robot before cleaning.
• Examine if the dustbin is empty and insure it is fixed before it works.
•  See if up-ground height sensor are wiped clean.
• If you only need to clean one room, please close the door.
•  If the room which needs to be cleaned wants a partition, you can place the virtual wall, at the same time, check the facing opening width.
•  Please be aware that device needs 8 cm of clearance underneath furniture so that it will not become trapped.
•  Do NOT drop the Robot, should this happen, run the Robot to see that everything is okay before letting it operate by itself without you being present.
•  If the battery is leaking, remove it immediately; it can damage the vacuum cleaner.
•  Keep batteries out of reach of children and incapacitated people. A person, who would swallow the batteries, must seek medical help immediately.
• Dispose of a discharged battery in a suitable way.
•  Never use the appliance for any other purpose than for the intended one described in these instructions for use! This appliance is not intended for outdoor use.
• The manufacturer is not responsible for damage caused by improper use of the appliance
  and the accessories and its guarantee for the appliance does not apply in situations when the safety warnings above are not complied with. Failure to replace or maintain all filters regularly and also using non-original filters, the properties of which resulted in failure or damage of the vacuum cleaner is also understood to be improper use of the appliance.

Wireless connection and compatibility

•  The ETA company cannot be liable in any way for any incidental, indirect or consequential damages, or for any loss of data or loss due to information leakage during wireless communication.
•  Successful wireless communication cannot be guaranteed 100% on all Smart devices and Wifi networks (routers). Due to the variety of devices on the market, there may be cases where the character or specification of a given smart device or Wifi network (router) makes connection impossible or is in some way disturbed. In addition, several factors, including hardware and software configuration, also affect the success of wireless communication over a Wifi network. The connection between the robot and your Wifi network can also be adversely affected by the surrounding Wifi networks that they can be tuned to the same channel and disrupt connections (e.g. in housing estates, apartment buildings, etc.). These facts are not a reason to claim the appliance.

The application is owned and operated by a third party (hereinafter the “Subject”) different from HP TRONIC Zain, Ltd. (hereinafter the „Seller“). No personal information is transmitted between the Subject and the Seller. When registering for the application, the customer transfers
the personal data directly to the Subject, which becomes the personal data controller. The Application and the associated privacy policy are governed by the Rules of the Subject.

•  No one else can disassemble maintain or. Transform the product except the maintenance technicians designated by our company or it may cause fire electric shock or personal injury.
• Don’t touch high-voltage power cord of the electric appliance with your wet hand, or it may cause electric shock.
• Don’t twist your clothes or any part of your body (head, finger, etc.) into the brush or wheel of the Robot, or it may cause personal injury.
• Don’t use the Cleaner in commercial places, or the Cleaner may be damaged by excessive use.
• Check whether the adapter and connector are connected well, or it may cause charging failure or even fire.
• Please use the Cleaner cautiously in the presence of the children to avoid frightening or harming them.
• Don’t use other charger but the equipped one of the Robot, or it may cause product damage, electric shock or fire due to high voltage.
• Don’t bend the power cord overly or place weight on it, or it may cause power cord damage, fire or electric shock.
• Don’t approach cigarette, lighter, match and other heat objects or combustible materials such as the gasoline cleaner.
• Insert the power cord of the charger well or it may cause electric shock, short circuit, smoking or fire.

APPLICABILITY

The product, mainly applicable to home, hotel rooms and small office, is good for cleaning to various short-haired carpet, wood floor, hard floor, ceramic tile, etc. Since the vacuum cleaner moves freely in the space of your home, it is necessary to adapt the environment to this fact. Before use, remove all unwanted objects (stretched cables, scattered clothes, papers, bags, etc.) from the floor that could impede the movement of the vacuum cleaner or, conversely, fragile objects (e.g. glass and ceramic vases) that could be damaged by the vacuum cleaner.

PRODUCT COMPONENTS

PACKAGE CONTENTS

| ****

Robotic vacuum cleaner

| ****

A

| ****

1

|

Charger station

| ****

D

| ****

1

|

Remote control

| ****

F

| ****

1

|

Power adapter

| ****

E

| ****

1

|

Mop extension

| ****

G

| ****

1

Item| Description| Designation|

Quantity

|
---|---|---|---|---
|

Mop

| ****

G4

| ****

2

**| Cleaning tool| I| 1
**| ****

Side brushes

| ****

A7

| ****

2

|

HEPA filter

| ****

B3

| ****

1

ROBOTIC VACUUM CLEANER

• A – Robotic vacuum cleaner
• A1 – Front bumper
• A2 – Sensors against falling downstairs A3 – Charging contacts
• A4 – Storage battery compartment cover A5 – Drive Wheels (Left / Right)
• A6 – Front wheel
• A7 – Side brushes
• A8 – Main brush
• A9 – Main brush cover
• B – Dirt hopper
• B1 – Dirt tank release button
• C – Control panel

DUSTBIN

• B – Dirt hopper
• B1 – Dirt tank release button B2 – Dirt tank
• B3 – HEPA filter
• B4 – Protective filter
• B5 – Lid part with filters

CONTROL PANEL

• C – Control panel
• C1 – Button ON / OFF / AUTO (automatic cleaning) / STOP (PAUSE)
• C2 – Charging light
• C3 – Wifi light
• C4 – Operation light

CHARGER STATION

• D – Charger station
• D1 – Operation indicator
• D2 – Power adapter connector D3 – Charging contacts
• E – Power adapter

REMOTE CONTROL

• F – Remote control

• F1 – Display

• F2 – Smart (automatic cleaning) / STOP (PAUSE) / button

• F3 – Directional buttons for manual control
  (FORWARD / BACKWARD / RIGHT / LEFT) F4 – Button for setting the scheduled cleaning time F5 – Button for setting the current time

• F6 – Button for return to charging station

• F7 – Button for automatic cleaning + button setting the suction power level

• F8 – Button for setting the cleaning mode

MOP EXTENSION

• G – Mop extension
• G1 – Mop attachment lock button
• G2 – Rubber stopper
• G3 – The lower part for attaching the mop G4 – Mop

SPARE PARTS LIST

• Side brushes (left + right): ETA221900030
• HEPA filter: ETA221900010
• Mop: ETA221900060
• Main brush ETA221900080
• Charging station ETA221900140
• Magnetic tape: ETA221900290

PREPARATION FOR USE

Remove all packing material, remove vacuum cleaner and accessories. Remove any adhesive, stickers, or paper from the vacuum cleaner.

VACUUM CLEANER PREPARATION

According to use, install the dustbin B or moping attachment G.

CHARGER STATION INSTALLATION

1.  Place the charging station on the floor. Make sure there is enough space on the sides of the base (at least 0.5 m) and in front of the base (at least 1.5 m).

2. Connect the adapter to the charging station and then to the wall outlet.

INSTALLATION OF SIDE BRUSHES

Install the side brushes. Make sure they are in the correct position (L – left, R – right).

VACCUM CLEANER USE

Insert the battery into the remote control, observe correct polarity (2 pieces, battery type AAA).

SWITCHING ON THE VACUUM CLEANER

• Press and hold the C1 button.
•  The C4 operation light comes on.

BATTERY CHARGING

• Check that the charging station is properly connected to the mains.
•  Place the vacuum cleaner near the charging station and press the F6 button on the remote control. If the battery is too low, place directly and correctly the vacuum cleaner on the charging station.

Set power

|

**Running Time ***

---|---
MIN| Approx. 140 minutes
NORMAL| Approx. 100 minutes
MAX| Approx. 60 minutes

• Note: The stated operating times are based on ETA‘s internal testing and only apply to a new and fully charged battery. Depending on the age and wear of the battery, the operating time decreases.

Remarks

• The standard charging time is approx. 5-6 hours.
• After cleaning, the vacuum cleaner will automatically search for the charging station.
•  The “ETA SMART” application makes it easy to find out the battery status. The application can also be sent back to the charging station at any time.

START / STANDBY / SLEEP MODE

• Start (Cleaning)
  Press the C1 button on the control panel or using the remote control F start the vacuum cleaner.

• Standby mode (Pause)
  Press the C1 button on the control panel or the F2 button on the remote control to interrupt the ongoing cleaning and put the vacuum cleaner in standby mode. In this state, the C4 operation indicator light flashes.

• Sleep mode
  If the vacuum cleaner is in standby mode and no task is assigned to it for 10 minutes, it will automatically go into sleep mode.
  Note: From sleep mode, press C1 on the control panel or key F2 on the remote control to put the vacuum cleaner into standby mode.

CLEANING MODES AND DEVICE FUNCTIONS WITHOUT USING THE ETA SMART

APPLICATION

Manual operation
You can operate the device manually using F3 direction buttons and clean only the areas where cleaning is necessary.
Notice: When operating the vacuum cleaner manually, always watch and be especially careful when using the BACK direction, as the vacuum cleaner does not have sensors at the rear against falling down the stairs.
Smart automatic cleaning (AUTO)
Press the C1/F2/F7 button to start automatic cleaning. If you start automatic cleaning with the F7 key or if you want to set the suction power level during cleaning, the ” ” and ” ” symbols will light up on the remote control display. If you use the C1/F2 button to start automatic cleaning, only the current time will light up on the display. During cleaning, the vacuum cleaner moves gradually and systematically in the space according to the programmed route. As soon as the vacuum cleaner cleans the entire available space, it automatically searches for the charging station. This is the most used method of cleaning.
Room cleaning (ROOM)
Press F8 button repeatedly to set the room cleaning mode. The symbols will light up on the remote control display ” ” and ” “. The vacuum cleaner moves freely around the room during this cleaning mode. Before starting this cleaning, close the door of the room you want to clean. This cleaning mode is suitable for cleaning only one room.
Cleaning along the walls (EDGE)
Press F8 button repeatedly to set the cleaning mode along the walls. The symbols ” ” and ” ” will light up on the remote control display. In this mode, the vacuum cleaner will focus on cleaning along the walls (furniture). After cleaning, the vacuum cleaner automatically searches for the charging station.
Suction power level setting
The suction power level can only be set in automatic (AUTO) cleaning mode. After starting the vacuum cleaner in this mode, you can switch between the individual suction power levels with the F7 key. There are a total of 3 levels of suction power. It is also not possible to change the suction power level when the mop attachment is fitted.
Return to the charging station
In the modes of automatic cleaning and cleaning along the walls, the vacuum cleaner has the function of automatic return to the charging station after the cleaning is completed. You can also send the vacuum cleaner to the charging station using the F6 button on the remote control.
Moping function
Use the F8 key to set the moping function. The symbol ” ” will light up on the remote control display. This function can only be used with the G mop attachment installed.

 CURRENT TIME AND SCHEDULED CLEANING

For the scheduled cleaning to function properly, the current time must first be set on the remote control.
Warning: If you remove the batteries from the remote control, the current time and the scheduled cleaning time will be deleted.

Current time setting

1. Make sure the vacuum cleaner is switched on.

2. Aim the remote control towards the vacuum cleaner and press the F5 key. The numeric value for setting the clock starts flashing.

3. Then you can use the F3 keys to set the time
   (FORWARD / BACKWARD – setting a numerical value; LEFT / RIGHT – switching between setting the value of hours and minutes).

4.  To confirm the set time, press the F5 key.

Note: When setting the current time, always point the remote control at the vacuum cleaner and keep a maximum distance of 3 m.

Scheduled cleaning setting

1.  Make sure the vacuum cleaner is switched on.
2. Aim the remote control towards the vacuum cleaner and press the F4 button. The numeric value for setting the clock starts flashing.
3. Then you can use the F3 keys to set the time of the scheduled cleaning (FORWARD / BACKWARD -setting a numerical value; LEFT / RIGHT switching between setting the value of hours and minutes).
4. To confirm and save the set scheduled cleaning time, press the button F4.

NOTE:

1.  When setting the time of the scheduled cleaning, always point the remote control at the vacuum cleaner and keep a maximum distance of 3 m.
2.  Scheduled cleaning can be activated / deactivated by long pressing the F4 key. If the scheduled cleaning is activated, the ” ” symbol will light up on the remote control display.

USING THE MOPING ATTACHMENT

1. Attach the G4 mop to the lower part of the moping attachment correctly. Soak and wring the mop before use.

2. Open the rubber stopper G2 and fill the mop attachment with water.

3. Place the mop attachment in place in the vacuum cleaner.

4. Switch the vacuum cleaner to the desired cleaning mode.

Notes:

•  When mopping, we recommend cleaning the individual rooms.
• When mopping, check the vacuum cleaner and add water to the moping attachment, if necessary, or rinse the mop.
• Do not use the mop attachment on carpets and prevent the vacuum cleaner from hitting the carpet.
•  Remove and clean the moping attachment after use. Do not leave it installed on the vacuum cleaner while charging.

USING MAGNETIC TAPE

Notice: Magnetic tape is not included in the package. However, it can be purchased separately (see paragraph 3.8 SPARE PARTS LIST).
The magnetic tape creates a virtual wall that will not allow the vacuum cleaner to continue. This allows you to demarcate areas where cleaning is not required. To ensure maximum efficiency, always place the magnetic tape flat and on a flat floor (you can also place it under the carpet). The tape can be cut according to the individual needs of the room (minimum length of the cut piece is 50 cm).

 APPLICATION ETA SMART

In the simple operation mode, the device can be controlled using buttons on control panel C or remote control F (see above). In order to use all device´s functions, you will have to install and use smart app “ETA SMART”, allowing extension of vacuum cleaner functionality and increased user comfort.
All other information, operating instructions of the app, instructions and hints for successful pairing with home network can be found at:
www.etasince1943.com/robot The app is available from Apple Store or Google Play database (or use the following QR code for easy installation:
Remarks
If QR code is not active, find the app manually (by its name).

VACUUM CLEANER MAINTENANCE

Carry out maintenance and cleaning regularly, depending on the frequency of use and the amount of cleaning. In a more polluted environment (a pet household), more frequent maintenance will be required. Failure to carry out maintenance may damage the vacuum cleaner and its components!

CHARGING CONTACTS CLEANING

Switch off the vacuum cleaner and disconnect the charging station from the power supply! Clean the charging contacts (A3, D3) on the vacuum cleaner and on the station with a soft dry cloth. Clean at least once a month. Do not use aggressive cleaning agents or oils to clean the contacts.

DIRT TANK AND FILTERS CLEANING

1.  Remove the dirt tank B from the vacuum cleaner. Dispose of dirt together with normal household waste.

2.  Clean the dirt tank with the tool I (or other suitable).

3.  Remove the filters from the dirt tank and clean them with tool I (or other suitable). Blow or knock the HEPA filter B3 gently.

NOTICE:

1. For filters cleaning do not use aggressive detergents or cleaning agents or hot water
2. Dry cleaning is recommended to maintain HEPA filter parameters.
3.  If you choose to wash the HEPA filter with water, its filtering ability will be reduced.
4.  The maximum number of filter washes is 3x. Then it is necessary to buy a new one.
5.  It is recommended to change the HEPA filter at least twice a year.
6.  The filters are not intended for use in a dishwasher.
7. Cleaning failure and possibly filters replacing can lead to malfunction of the vacuum cleaner! **  

**

4. After maintenance, remove the dirt tank including filters and put it back in the vacuum cleaner.

MAIN BRUSH CLEANING

1.  Press the cover towards you and remove the cover A9 and remove the main brush A8 from the vacuum cleaner.
2. Clean the main brush with the cleaning tool I (or other suitable). You can also use scissors to remove tangled hair / hair. Wipe the main brush cover and main brush compartment with a soft, dry cloth.

SIDE BRUSHES CLEANING

Remove the two side brushes, clean them and remove the twisted hair / pet’s hair).

WHEELS CLEANING

Clean the front, left and right wheels with the I device.

SENSORS CLEANING

After each cleaning, clean the sensors with tool I (or another suitable

one).
MOP EXTENSION CLEANING

Remove the extension from the vacuum cleaner after each use. Pour excess water from the reservoir. Rinse the mop extension under running water.

More extensive maintenance or maintenance requiring intervention in the inner parts of the appliance must be carried out by a professional service! Failure to comply with the instructions of the manufacturer will lead to expiration of the right to guarantee repair!

PROBLEMS SOLUTIONS

and clean the wheels
The vacuum cleaner is still backing up.| One of the sensors

in the front bumper s dirty or damaged.

| Clean the front bumper sensors. If the problem persists, contact an authorized service centre.
The vacuum cleaner constantly hits obstacles.| The front bumper is jammed due to dirt.| Check and clean the front bumper.
The vacuum cleaner cleans for a very short time.| The storage battery is not charged enough or is at the end of its life.| Fully charge the vacuum cleaner. If the problem persists, replace the storage battery with a new one.
The suction power of the vacuum cleaner decreases.| The dustbin is full or the filters are dirty.| Check and clean the dustbin and filters.

TECHNICAL SPECIFICATION

Robotic vacuum cleaner

Appliance protection class| III.
operating voltage| 14,4 V (DC)
Accumulator| Li-Ion
Battery savings| 3000 mAh
Charging time| 5-6 hood.
Weight| 2.7 kg
Dimensions| Ø 330 mm x 74 mm
Frequency range| 2.4 GHz
Output power (EIRP)| 15.95 dBm
Wireless technology| Wifi
Declared acoustic level is 63 dB(A) re 1pW.

Compatibility:

• Smart device operational system
  • Android 6.0 and higher
  • IOS 9.0 and higher
• WiFi network – 2.4 Gaz
  • WPA1 and WPA2 security (recommended WPA2)

Charging adapter

Device manufacturer’s name or trademark, business registration number and address| ETA
AC adapter model identifier| GQ12-190060-AG
Input voltage| 100-240 V (AC)
Input frequency| 50/60 Hz
Output voltage| 19 V (DC)
Output current| 0.6 A
Output power| 11.4 W
Average efficiency in active mode| 84.42 %
Low load efficiency (10%)| 78.08 %
Power consumption without load| 0.084 W
Appliance protection class| II.

Hereby, ETA as. declares that the radio equipment type ETA2219 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://eta.cz /declaration-of-conformity The manufacturer reserves the right to change the technical specifications for the respective model. The manufacturer reserves the right to change/update the ETA SMART application without prior notice. Due to the character of such changes/updates, some information or procedures in this manual might become obsolete or might be missing.
Guarantee of 24 months does not apply to decrease in the accumulator’s effective capacity caused by its use or age. Effective capacity gradually decreases depending on the method of use of the accumulator.

ENVIRONMENTAL PROTECTION

If the dimensions allow, there are labels of materials used for production of packing, components and accessories as well as their recycling on all parts. The symbols specified on the product or in the accompanying documentation mean that the used electrical or electronic products must not be disposed of together with municipal waste. For proper disposal of the product, hand it over at special collection places where it will be received free of charge. Suitable disposal of the product can help to maintain valuable natural resources and to prevent possible negative impacts on the environment and human health, which could be the possible consequences of improper waste disposal. Fines can be imposed for improper disposal of this type of waste in agreement with the national regulations. The appliance is equipped with the Li-Ion battery with long life. For environmental protection it is necessary to remove the battery from the appliance after its service life and the battery and the appliance must be disposed of safely using special collection networks. Ask for more details at the local authority or at the local waste collection site. For environmental protection it is necessary to remove the battery from the appliance after its service life and the battery and the appliance must be disposed of safely using special collection networks. Ask for more details at the local authority or at the local waste collection site. Battery removing Remove the 2 battery compartment cover screws at the bottom of the vacuum cleaner. Remove the battery and unplug the connector. Remove the battery and unplug the connector. For unplugging the connector use more force for advantage of overcoming the safety fuse against spontaneous disconnection.

References

• Prohlášení o shodě | ETA - tady je doma
• Technická podpora robotických vysavačů | ETA - tady je doma
• AEG Hausgeräte | Setzen Sie auf Qualität | AEG
• Obsługa robotów odkurzających | eta-polska.pl
• ETA - tady je doma
• Technická podpora robotických vysavačů | ETA - tady je doma
• Robotporszívók műszaki támogatása – ETA HUNGARY
• ETA - tu je doma
• Robot vacuum cleaner support – ETA since 1943

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>