JFA K1200 Long Distance Remote Control Instruction Manual

JFA K1200 Long Distance Remote Control

DESCRIPTION

The K1200 allows you to control by distance¹ the main functions of the “player” and change music, folder, volume, pause, play, and power.

OPERATION

• Transmitter unit: whenever you press a key, the blue LED will light up, indicating transmission.
• Receptor unit: the “led action” will turn on indicating the presence of a received signal.

NOTE

• The central will not work if the coding procedure is not performed.
• Check the light intensity of the transmitting unit LED. If it is weak or does not light, replace the battery.

For a longer range, install the equipment in a location where the antenna is free and the most exposed as possible, the distance achieved is 1200 meters in an open area.

BASIC COMMANDS TRANSMITTER UNIT

1. Volume control (+);
2. Volume control ( _ );
3. Rewind the music;
4. Advance the music;
5. LED indicator;
6. Go up the folder;
7. Go down the folder;
8. Play/pause / ATT;
9. Power/function (switches to aux, CD, USB, radio, etc.).

BASIC COMMANDS OF THE RECEIVER UNIT

1. RF receiver antenna;
2. LED action, reception indicator;
3. LEARN MODE key;
4. MEMORY MODE switch;
5. Code IR (see learn mode);
6. 12V power (black-white stripe) and GND (black);
7. Infrared emitter (aim at the front of the player).

ENCODING THE CONTROL

1. LEARN MODE:
   (Learning the functions of the original control)

2. Press the “A” key (note 1) the Led action will be constantly on;

3. Press the key of the k1200 Control (note 2), that you want to record until the “Led action” stay flashing;

4. Point the original player control to the IR code entry and press the key you want to record (note 4) until the LED action flashes quickly, and then be constantly on;

5. Repeat steps 2 and 3 for the other keys;

6. After finishing this process press the key “A” (Note 1) of the receptor or wait 10 seconds to exit the mode.

MEMORY MODE:
(The receptor has stored in its memory codes the main models of “player” ( see the attached index or on the website: www.jfaeletronicos.com)).

1. Press the “M” key (Note 3), the LED action will be constantly on;
2. Press the key on the control (note. 2) corresponding to the model of the “player”, as the index, for example: to program the CD SONY, you should perform step 1, then press the keys in sequence, in the control. Check that the LED will flash one time and then 4 times, indicating that was programmed the model 14 (Sony).
3. After finishing this process press the key “M” (note 3) of the receptor or wait 10 seconds to exit the mode.

SETTING LEARN MODE AND MEMORY MODE

MEMORY MODE ENCODING TABLE 1

MEMORY MODE ENCODING TABLE 2

RECOMMENDED RECEIVER INSTALLATION

The installation of the equipment in the sound system is done through a polarized power cable. Make sure the white-striped wire from the receiver unit is connected to the battery’s direct positive (+12V) and the black wire to the negative (GND).

The receiving unit should preferably be fixed away from metal parts and the car’s bodywork (which degrades the transmission) keeping, whenever possible, the antenna unobstructed to allow the greatest possible range of the equipment.

Position the infrared emitter, from the receiver unit aimed at the player’s panel, so that there are no obstacles between them. It is recommended to install the receiver unit in the trunk and the IR emitter in the center of the rear window, pointing towards the front of the player. Make sure the wires are not crushed in the installation process.

RECOMMENDATIONS AND NOTES

1. Install the receptor unit at least 1 meter from the Alarms central or electronic injection module. It is recommended to install a receptor in the trunk and the infrared emitting in the rear seat pointing to the front of the “CD player”.
2. For greater range should keep the antenna stretched and in a location that is visual and away from the car bodywork.
3. supply the receiving unit with 12V.
4. The receptor can operate with two transmitters; for this, performing steps 1 and 2 to the new transmitter. This feature is recommended for customers using the Slim control on the steering wheel and a K1200 to control by distance from the player.

TECHNICAL SPECIFICATIONS

UNITY RECEIVER

• Operating voltage: 9 to 16 V
• Stand-by consumption: 13 mA
• Reverse polarity protection: YES

UNITY TRANSMITTER

• Battery model: A 23 – 12 V
• Operating Frequency: 433.92 MHz
• Reverse polarity protection: NO
• Radiated power (3 meters): 0.808 mW
• Modulation: ASK

“This equipment operates on a secondary basis, has not the right of protection against harmful interference, even of the same type of station, and not may cause interference to systems operating on a primary basis. “

FAQ’s

What is the range of the JFA K1200 Long Distance Remote Control?

The range can vary depending on the specific model, but it typically extends up to a certain distance (e.g., 100 meters or more).

What devices can the JFA K1200 control remotely?

The JFA K1200 may be designed to control a variety of devices, such as TVs, audio systems, projectors, and other compatible electronic equipment.

Does the JFA K1200 come with a user manual?

Usually, remote controls come with a user manual that explains how to set up and use the device effectively.

Can I program the JFA K1200 to work with my existing devices?

Many long-distance remote controls allow users to program them to work with specific devices through a setup process.

How do I pair the JFA K1200 with my devices?

The pairing process may vary based on the remote control and the devices you want to control. The user manual should provide step-by-step instructions.

Does the JFA K1200 use batteries or have a rechargeable battery?

Remote controls typically use batteries for power, but some models may have rechargeable batteries.

What is the battery life of the JFA K1200?

The battery life can vary depending on usage and battery capacity. Refer to the user manual or product specifications for estimated battery life.

Can the JFA K1200 control multiple devices simultaneously?

Some remote controls have the capability to control multiple devices, allowing users to switch between them easily.

Is the JFA K1200 compatible with smart home systems?

Depending on its features, the remote control may or may not be compatible with smart home systems.

Does the JFA K1200 support voice control?

Voice control may be a feature in some advanced remote controls, but not all models have this functionality.

Can I replace lost or damaged JFA K1200 remote controls?

It is often possible to obtain a replacement remote control through the manufacturer or authorized retailers.

Video – Product Features

Download this PDF Link:JFA K1200 Long Distance Remote Control Instruction Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>