PLANAR PT1945R Touch Screen Monitor User Guide

PLANAR PT1945R Touch Screen Monitor

Usage Notice

• Warning – To prevent the risk of fire or shock hazards, and do not expose the product to moisture.
• Warning – Please do not open or disassemble the product as this may cause electric shock.
• Warning – Power cord shall be connected to a socket-outlet with earthing connection.
• Warning – The cable cover cannot be removed under normal use conditions.
• Warning – Stability Hazard. The touch monitor may fall, causing serious personal injury or death. To prevent injury, this touch monitor must be securely attached to the wall in accordance with the installation instructions.

Safety Precautions

Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit.

Do:

• Turn off the product before cleaning.
• Surface may be cleaned using a soft clean cloth moistened with mild window glass commercial cleaners or 50/50 mixture of water and isopropyl alcohol.
• Use a soft cloth moistened with mild detergent to clean the display housing.
• Disconnect the power plug from AC outlet if the product is not going to be used for an extended period of time.

Don’t:

• Do not touch the LED display screen surface with sharp or hard objects.
• Do not use abrasive cleaners, waxes or solvents for your cleaning.
• Do not operate the product under the following conditions:
  • Extremely hot, cold or humid environment.
  • Areas susceptible to excessive dust and dirt.
  • Near any appliance generating a strong magnetic field.
  • In direct sunlight.
  • For over 16 hours per day.
• If smoke, abnormal noise or odor emits from your LED LCD Monitor, remove the power cord immediately and call your service center.
• Never remove the rear cover of your LED LCD Monitor. The display unit inside contains high-voltage parts and may cause electric shock.
• Never try to repair your LED LCD Monitor yourself. Always call your service center or a qualified technician to fix it.
• Due to safety concerns, if the VESA mounting kit is purchased separately, please make sure the mounting kit is UL-listed, and replaceable only by service personnel.

Introduction

About PT1945R/PT1945P
The PT1945R/PT1945P is a 19″ flat panel screen with an active matrix, thin- film transistor (TFT) edge-lit LED liquid crystal display (LCD). This unit is to be used as commercial and light industrial equipment only.

Features include:

• Analog signal input
• Dual digital signal inputs (HDMI & DP)
• Active matrix TFT LCD technology
• 1280 x 1024 SXGA resolution
• 19″ viewable display area
• 31.47 ~ 80 KHz horizontal scan
• 56 ~ 75 Hz high refresh rate
• 0.294mm x 0.294mm pixel pitch
• Auto adjustment function
• Multilingual OSD user controls
• Kensington security slot
• 100 mm VESA mount
• Removable base for flexible mounting solutions.
• PT1945R – 5-wire resistive touch screen with USB controller
• PT1945P – Projected Capactive touch screen with USB controller
• Build-in audio-1W x 2

Touch Screen for PT1945R

• Number of Touch Points: 1
• Analog 5-wire resistive touch screen for finger and stylus input
• Surface: Anti-glare treatment
• Interface: USB controller
• Transmittance: 82%±5%
• HID: Windows® 7/8
• Driver: VISTA, XP, 2000, CE, XP Embedded, Linux kernel 2.x.x / 3.x.x / 4.x.x / 5.x.x (32 bit & 64 bit), Apple® Mac OS, Android 2.3.X Upwards

Touch Screen for PT1945P

• Number of Touch Points: 10
• Projected Capactive touch screen for finger input only
• Surface: Glare treatment
• Interface: USB controller
• Transmittance: ≧85%
• HID: Windows® 7/8
• Driver: VISTA, XP, 2000, CE, XP Embedded, Linux kernel 2.x.x / 3.x.x / 4.x.x / 5.x.x (32 bit & 64 bit), Apple® Mac OS, Android 2.3.X Upwards

Package Overview

Installation

Front View

Bottom View (Without Stand)

VESA Mount Your Monitor
This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface standard which defines a physical mounting interface for flat-panel monitors and corresponds with the standards of flat panel monitor mounting devices, such as wall and table arms. The VESA mounting interface is located on the back of your monitor.
To mount the monitor on a UL-listed certified swing arm or other mounting fixture, follow the instructions included with the mounting fixture to be used.

Warning!

Please select the proper screws!
The distance between the back cover surface and the bottom of the screw hole is 11 mm. Please use four M4x16 screws diameter with proper length to mount your monitor.
Please note: the mounting stand must be able to support at least 11 lbs ( 5Kg).

Start Your Installation
Please follow these instructions so that you can hookup the cables to associated connector.

1. Lay the display flat on an even surface.
2. Move the stand into position as seen in the step 2 diagram.
3. Remove the cable cover as seen in the step 3 diagram.
4. Connect the cables to the appropriate connectors as seen in the step 4 diagram.
5. Position all cables under the cover lip as seen in the step 5 diagram.
6. Re-attach the cable cover . Remove the screw (CBM M3x6) from the accessory box, and insert the screw into the cable cover and monitor as seen in the step 5 diagram.

Connecting the Display (Figure 10.1)
To setup this display, please refer to the following figure and procedures.

1. Be sure all equipment is turned off.
2. Connect the AC power cord to the power connector on the monitor and the other end into an electrical outlet (10.1).
3. Connect the HDMI, DP or VGA cable from the display’s HDMI, DP or VGA input connector to the HDMI, DP or VGA connector of your host computer and tighten the screws (10.1).
4. If using VGA, connect the audio-in cable from the audio input port of your display to the audio out port of your computer (10.1).
5. Connect the USB cable from the USB port of your display to the USB port (10.1) of your computer.
6. Configure the touch screen. Refer to the “Touch Screen Driver Installation” section on page 21.
7. Once the touch screen is configured, the monitor is ready for use.

Notice!

To ensure the display works well with your computer, please configure the display mode of your graphics card to make it less than or equal to 1280 x 1024 resolution and make sure the timing of the display mode is compatible with the LCD display. We have listed the compatible “Video Modes” of your LCD display in the appendix (on page 20) for your reference.

(Figure 10.1)

Kensington Security Slot
The monitor can be secured to your desk or any other fixed object with Kensington lock security products. The Kensington lock is not included.

User Controls

Side Panel Controls

How to Use the OSD Menus

How to Operate OSD

1. Press the “MENU” button to pop up the “on-screen menu”
2. Press the “Up” or “Down” button to navigate in the main menu and sub-menu.
3. Choose the adjustment items by pressing the “” SELECT “ button.
4. Adjust the value of the adjustment items by pressing the “Up” or “Down” button
5. Press “SELECT” to Enter, and press “MENU” to exit.
6. The OSD menu will automatically close if left idle for a preset time.

Lock/Unlock OSD/Power buttons

1. To Lock or Unlock the OSD / Power buttons, press “Menu” and “Down” at the same time. This will activate an OSD window as follows:
2. Choose to activate OSD or Power Key lock. Choose Yes or No to lock or unlock.

Note:
When the OSD Key function is locked, all the buttons except “power” button are now disabled. When the Power Lock function is locked, the power key is disabled. User cannot turn off the monitor by “Power” key.

Enable/Disable Touch Function

1. To disable the touch function, press “Menu” and “Enter” Key, at the same time.
2. To enable the touch function, press “Menu” and “Enter” Key, at the same time for five seconds.

Powering off the monitor
Powering off the monitor requires 3 presses to the power key. This is designed to prevent accidental power off.

1. Press the power key once, an OSD window will pop up “Do you want to turn off”.
2. Press the power key again. Another OSD window will pop up “Please press the power
3. Press the power key one last time to turn off.
4. If you do not press the power key in five seconds, the OSD window will be gone and return to the normal status instead.

Source Select
During On mode: Pressing “Select” key for 3 seconds, will pop up “source select” OSD. During Sleep Mode: Pressing “Select” key for 1 seconds, will pop up “source select” OSD.
Factory Mode
This mode is reserved for maintenance.

Appendix

Troubleshooting
If you are experiencing trouble with the display, refer to the following. If the problem persists, please contact your local dealer or our service center.

Problem: No image appears on screen.

• Check that all the I/O and power connectors are correctly and well connected described in the “Installation” section.
• Make sure the pins of the connectors are not crooked or broken.

Problem: Partial Image or incorrectly displayed image.

• Check to see if the resolution of your computer is higher than that of the display.
• Reconfigure the resolution of your computer to make it less than or equal to 1280 x 1024.

Problem: Image has vertical flickering line bars.

• Use “Fine” to make an adjustment.
• Check and reconfigure the display mode of the vertical refresh rate of your graphic card to make it compatible with the display.

Problem: Image is unstable and flickering

• Use “Horizontal size” to make an adjustment.

Problem: Image is scrolling

• Check and make sure the VGA signal cable (or adapter) is securely connected.
• Check and reconfigure the display mode of the vertical refresh rate of your graphics card to make it compatible with the display.

Problem: Vague image (characters and graphics)

• Use “Fine” to make an adjustment. If this problem still exists, use “Horizontal size” to make an adjustment.

On-Screen Display Menus

Main OSD Menu:

Warning Signal

If you see warning messages on your screen, this means that the display cannot receive a clean signal from the computer graphics card.
Below are the three kinds of Warning Signal. Please check the cable connections or contact your local dealer or Planar for more information.
No Signal
This message means that the display has been powered on but it cannot receive any signal from the computer graphics card. Check all the power switches, power cables, and VGA signal cable.
Going to Sleep
The display is under the power saving mode. In addition, the display will enter power saving mode when experiencing a sudden signal disconnecting problem.
The monitor can be activated by pressing any key on the keyboard, triggering the mouse or touching the screen.
Out of Range
This message means that the signal of the computer graphic card is not compatible with the display. When the signal is not included in the “Video Modes” list we have listed in the Appendices of this manual, the monitor will display this message.

Product Dimensions

PT1945R

Front View

Side View

Top View

PT1945P

Front View

Side View

Top View

Compatibility Modes

Touch Screen Driver Installation
Windows 7/8/10 Multi touch without driver(support by HID) The PT1945R/PT1945P is available with USB connection. The touch driver is available at www.planar.com/support for these operating systems: Windows® 7/8/10, VISTA, XP, 2000, CE, XP Embedded, Linux kernel 2.x.x / 3.x.x / 4.x.x / 5.x.x (32 bit & 64 bit), Apple® Mac OS, Android 2.3.X Upwards.

Please Note:

1. The PT1945R/PT1945P is Microsoft® Windows® HID (Human Interface
   Device) compatible if you use the USB touch screen interface. No additional software driver is required for general operation of the touch screen. A calibration tool can be installed for improved touch position accuracy. See “Optional Calibration Tool Install” section for more information.

2. For PT1945P, the system requires 15 seconds for Windows 7/8 to install/uninstall the touch drivers while turning power on/off or plugging/unplugging USB cable.

PT1945R Optional Calibration Tool Install:
If you would like to use the Optional Calibration Tool, follow the instructions below. Please note: the calibration tool supports Windows® 7/8, VISTA, XP, XP Embedded, 2000, 98 and ME operating systems via USB only.

1. Visit www.planar.com/support.
2. Select the monitor size and then model name.
3. Click on the “Load Utility” button that appears to the right of the model name.
4. The HID calibration tool will automatically open. From here the user can choose to do the following:
   • 4 Points Calibration
   • 9 Points Linearization
   • 25 Points Linearization
   • Clear
   • Draw Test
   • Advanced. In the Advanced settings area the user may do the following:
   • Adjust the Double Click Area.
   • Enable auto right click and adjust the auto right click time.
   • Choose to be either in the HID Mouse Mode or HID Digitizer Mode (Windows® 7/8 only).
   • Simply click the “Apply” button once the settings are finalized.

PT1945P Optional Calibration Tool Install:
Calibrating the touch screen in Windows 7/8:

1. Tap the Start button, Control Panel and then Hardware and Sound.
2. Under Tablet PC Settings, tap Calibrate the screen for pen or touch input.
3. On the Display tab, under Display options, tap Calibrate and then Yes to allow the program to make changes.
4. Follow the on-screen instructions to calibrate the touch screen.

PT1945R Install Instructions:
If you are using a PC running Windows® 7/8, VISTA, XP, 2000, 98, NT4.0, follow the instructions below:

1. Power on the PC.
2. Be sure the USB cable is connected from the PC to the display.
3. Visit www.planar.com/support.
4. Follow the step-by-step instructions as shown on the pop-up windows.

If you are using a PC running driver Linux kernel 2.x.x / 3.x.x / 4.x.x / 5.x.x (32 bit & 64 bit), follow the instructions below:

1. Power on the PC.
2. Be sure the USB cable is connected from the PC to the display.
3. Visit www.planar.com/support.
4. Follow the step-by-step instructions as shown on the pop-up windows.

If you are using a PC running Windows® XP Embedded, follow the instructions below:
Express:

1. Power on the computer.
2. Make sure that the USB cable is connected to the computer.
3. Be sure that your EWF is disabled. If your EWF is enabled, please disable the EWF by using the EWF Manager command.
4. Once the EWF is disabled click on the XP driver at www.planar.com/support. and follow the step-by-step instructions as shown on the pop-up windows.

Custom:

1. Power on the computer.
2. Make sure that the USB cable is connected to the computer.
3. Follow the step-by-step instructions found in the zipped file at www.planar.com/support. 

If you are using a PC running Windows® CE, follow the instructions below:

1. Power on the computer.
2. Make sure that the USB cable is connected to the computer.
3. Using Platform Builder, build an image file by following the step-by-step instructions found in the zipped file at www.planar.com/support. 

If you are using a PC running Linux or Apple® Mac OS, follow the instructions below:

1. Power on the computer.
2. Make sure that the USB cable is connected to the computer.
3. Follow the step-by-step instructions found in the zipped file at www.planar.com/support. 

When changing the Touch Interface (USB), please follow instructions below.

1. Uninstall the touch driver.
2. Re-start the computer.
3. Remove the original Touch Interface.
4. Connect the computer to the Touch Interface that you would like to use.
5. Install the Touch driver, then follow the step-by-step instructions as show on monitor.

PT1945P Driver Install Instructions:
If you are using a PC running, Windows® 7/8, VISTA, XP, 2000, follow the instructions below:

1. Power on the PC.
2. Make sure that the USB cable is connected to the computer.
3. Visit www.planar.com/support.
4. Follow the step-by-step instructions as shown on the pop-up windows.

If you are using a PC running driver Linux kernel 2.x.x / 3.x.x / 4.x.x / 5.x.x (32 bit & 64 bit), follow the instructions below: 

1. Power on the PC.
2. Make sure that the USB cable is connected to the computer.
3. Visit www.planar.com/support.
4. Follow the step-by-step instructions as shown on the pop-up windows.

If you are using a PC running Windows® XP Embedded, follow the instructions below:
Express:

1. Power on the computer.
2. Make sure that the USB cable is connected to the computer.
3. Be sure that your EWF is disabled. If your EWF is enabled, please disable the EWF by using the EWF Manager command.
4. Once the EWF is disabled click on the XP driver at www.planar.com/support. and follow the step-by-step instructions as shown on the pop-up windows.

Custom:

1. Power on the computer.
2. Make sure that the USB cable is connected to the computer.
3. Follow the step-by-step instructions found in the zipped file at www.planar.com/support. 

If you are using a PC running Windows® CE, follow the instructions below:

1. Power on the computer.
2. Make sure that the USB cable is connected to the computer.
3. Using Platform Builder, build an image file by following the step-by-step instructions found in the zipped file at www.planar.com/support. 

If you are using a PC running Linux or Apple® Mac OS, follow the instructions below:

1. Power on the computer.
2. Make sure that the USB cable is connected to the computer.
3. Follow the step-by-step instructions found in the zipped file at www.planar.com/support. 

Technical Support

Cables and Accessories
To find cables and accessories for your Planar monitor, touch screen or other Planar products visit our online store at www.PlanarOnline.com.
Technical Support
Visit Planar at http://www.planar.com/support for operations manuals, touch screen drivers, warranty information and access to Planar’s Technical Library for online troubleshooting. To speak with Planar Customer Support please have you model and serial number available and dial:
Planar Support
Tel: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the US.
Hours: 24 hours a day, 7 days a week.
Toll or long-distance charges may apply.
European Product Database for Energy Labeling (EPREL)
PT1945R Registration number: 727454
PT1945P Registration number: 727453

Planar Systems, Inc.
Customer Service
24×7 Online Technical Support: http://www.planar.com/support
Planar address: 1195 NE Compton Drive Hillsboro, OR 97006 USA
Tel: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the United States. Hours: 24 hours a day, 7 days a week
© 06/2021 Planar Systems, Inc.
Planar is a registered trademark of Planar Systems, Inc. Other brands and names are the property of their respective owners. The technical information in this document is subject to change without notice.

FCC STATEMENT

FCC RADIO FREQUENCY INTERFERENCE STATEMENT WARNING: (FOR FCC-CERTIFIED MODELS)
This LED LCD Monitor has been tested and found compliant with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide proper protection against harmful interference to a residential installation. This LED LCD Monitor generates, uses, and can radiate radio frequency energy. Harmful interference to radio communication may be the result if it‘s not properly installed and used. However, there is no guarantee that interference will not occur in a particular installation. If this LED LCD Monitor does cause serious interference to radio or television reception, resetting may correct it. Moreover, users are encouraged to reduce interference by doing one or more of the following:

• Reorient or relocate the receiving antenna.
• Move the LED LCD Monitor and the receiver further away from each other.
• Connect the LED LCD Monitor into an outlet on a circuit different from that to which the receiver is connected.
• Consult your local dealer or a qualified technician.

FCC Warning:
To assure continued FCC compliance, a user must use a grounded power supply cord and the provided shielded video interface cable with bonded ferrite cores. Also, any unauthorized changes or modifications to this LED LCD Monitor would void the user‘s authority to operate this device.
Note: If necessary, shielded interface cables and AC power cord must be used to meet the emission level limits.

References

• Planar LED & LCD Video Walls & Display Solutions | Planar
• Planar Environmental Initiatives | Planar
• Planar Support | Planar
• Planar LED & LCD Video Walls & Display Solutions | Planar

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>