merax KJ600FK09B Air Purifier User Manual

merax KJ600FK09B Air Purifier

USER MANUAL

Dear Customer

Thank you for purchasing our air purifier.

In order to facilitate the installation and use of this machine, we recommend that you carefully read this manual, and keep it stored safely. To ensure that you always enjoy fresh air, use this manual for qualified and standardized installation, proper use, and maintenance. This will ensure you always enjoy the fresh air. Our air purifier was developed by our researchers bringing together technology from home and abroad to give you the latest generation of air purification devices. If any questions arise from use, please consult this manual. If it is in accordance with the warranty, we kindly welcome you to contact us with the address and phone number on the card. We welcome any comments or suggestions you have about our product and service.

Performance Index

• Product maintenance and filter replacement cleaning information, please refer to the instruction manual;
• Purification performance parameters are tested under specific third-party laboratory conditions with specific dust particles and formaldehyde gas as target pollutants;
• The recommended area is calculated according to (0.07-0.12) SCADA particles, which is the theoretical value. With the different use environments and building structures,The applicable area will also change due to various factors such as the degree of indoor pollution.

Product Features

Pre-filter

The primary filter is the primary filter of the air purifier. It is mainly used to filter dust particles, including large particles of dust, dander, pollen, floating matter, and other pollutants. Can be cleaned many times and reused.

HEPA H13 Composite Filter

The HEPA H 13 composite filter consists of HEPA H 13, adsorption purification materials, catalytic purification materials, and functional filtration materials. It can filter out smoke, dust, pollen, allergens, pollutants and fine particles larger than 0.3 microns, which can filter out harmful gases such as benzene formaldehyde and malodor.

Anion Purifier

The release of a large number of negative ions is due to the addition of an outer electron to the oxygen molecule to obtain negative charges, so it has an extraordinary binding ability, so that normally positive charged indoor floating dust, smoke, pathogens, viruses gather together, lose the ability to float freely in the air, and fall rapidly, thus purifying the air, purifying the environment, and no longer harmful to the human body. These ultrafine particles are difficult to be filtered by general mechanical equipment, and the negative air ions have a special ability to capture these harmful substances. The smaller the particle size, the higher the capture rate, which is an effective way to eliminate this pollution.

Product Appearance and Structure

Installing the Filter

Removing the filter from the plastic bag

• Remove the front cover
• Remove the filter
• Take the filter out of the packaging
• Make sure to remove the plastic bag off the filter before use.

Installing the filter and front cover.

• There are differences between the inside and the outside of dust filter 1 (HEPA H 13 composite filter).Attention: The side with a handle should be placed outwards.
• There are differences between the inside and the outside of the front filter (pre-filter).
• Attention: The side with a handle should be placed outwards.
• Install the front cover.
• The machine will not run if the front panel is uncovered.

Function Description

Powering On

1. When the machine is plugged in and on standby, the “power” button works to turn on the machine. After this button is touched for the second time, the machine turns to a standby state. (The icon is red when standby and orange when on.)

Selecting the Operating Mode

1. When the machine is on after the “auto” button is touched, the negative ion generator and the auto-icon will start to work, and the gear will be changed according to the sensor’s data. (The icon will stay on when the machine operates in auto mode, otherwise, it will be off.) Attention: If users change “wind speed” under the auto mode, the machinen will quit this mode automatically.
2. When the machine is on, every touch of the “timing” button will add 1 hour to the timing. When it accumulates to 12 hours, one more touch will turn it off. (The icon will stay on when the machine operates in timing mode, otherwise, it will be off.)
3. When the machine is on, pressing the “negative ion” button will turn on negative ion mode, and pressing one more time will turn it off. (The icon will stay on when the machine operates in negative ion mode, otherwise, it will be off.)
4. In the open state, pressing speed smoke purification, the machine runs at the highest level (six At this time, the efficiency of purification is the greatest. Then press once more, will turn off the function. (the icon of the key button is lit when the bullion is opened, and the icon is not bright when it is closed.)
5. This machine has a filter timing reminding function, setting time for 1500 hours, when the machine runs to set time. the indicator light on the panel will light up, reminding the user to replace the filter. The reset function of the button at this time ils effective, touch this button to reset the timing and reopen the timing.
6. In the open state, when the sleep function is opened, the machine screen closes and the whole light of the machine closes. The machine can only work in the sleep mode, not controlled by the sensor. If the timing function is opened. The machine will work until the set time. And then will go into the standby state. (the icons of the button will light on when the sleep function opens, then the machine goes into sleep after a while, and the lights are all out.)

Note: in automatic mode, when the light of the environment is less than 5-10 Ims and the duration is up to 3 minutes, the machine will automatically enter the sleep mode. When ambient light is greater than 10 I’m and the duration is 5 minutes, the machine is out of sleep mode. Working state.

1. When the machine is on, touch the “child-lock” button to lock all the buttons. At that time all the buttons have no reaction to any touch, while the machine still works how it is set before. Press the “child-lock” button for 5 seconds and the machine will quit this mode. (The icon will stay on when the machine operates in child-lock mode, otherwise, it will be off.)
2. When the machine is on, touch”+” or “-” to switch the gear and change the operating speed. After the gear is changed, the motor will work only at the setting level without being affected by the sensor. (Touch the “wind speed” button, and the machine will quit auto mode)

Display function description

1. When the power is turned on, the PM2.5 sensor needs to be warmed up for 1 minute to display data, and the display data range is 1-500um/m3. When the current display shows PM2.5 data, the PM2.5 and um/m3 icons light up. When the current display shows that it is not PM2.5 data, the PM2.5 and um/m3 icons are not lit.
2. When the timing function is turned on, this area displays the time unit in hours, and displays “00” when there is no timing function.
3. Wind speed gear line corresponding to wind speed gear, from the bottom to up, each line represents a gear, the highest gear is five.
4. This icon is displayed as a WIFI connection state, longe press the negative ion key for 5 seconds in the standby state. This pattern enters the flickering state (flash for 1 second once), at this time the mobile phone APP and the machine will go into in the match state, press the mobile phone APP pair operation, and after successful pairing, this pattern light will be on continuously, when the machine is in the environment where there is no WIFI signal. At the time, this pattern is not bright.
5. Air quality operating lamp and wind speed gear
6. Green: very good quality: PM2.5=1-35 (wind speed gear two)
7. Blue: good quality: PM2.5-36-75 (wind speed gear three)
8. Yellow: general quality: PM2.5=76-150 (wind speed gear four)
9. Red: poor quality: PM2.5=151-500 (wind speed gear five)
10. Speed mode (wind speed gear six)

Shutdown

• In the open state, the “power” button on the touch panel is touched and the machine enters the standby state. Light red when in standby state) power supply.

Function

This product is equipped with a remote control, and a button battery (if the remote control is not used for a long time, please remove the battery).

Note: the buttons on the remote control corresponding to the keys on the operation panel. The operation function and method are the same. (except for no long-press function)
Note: when the remote control is first used, please take out the lid of the battery and take out the protective film on the battery. Put back the battery cover, otherwise, the remote control will not be electrized and not function.

How to Use

1. Auto mode. When the machine is plugged in, press the “power” button and the “auto” button in sequence, then it can operate under the control of IntelliSense. The motor’s operating gear will adjust automatically to the PM2.5 data collected by the sensor. This mode is suitable for most situations.
2. Compulsory mode. When the machine is plugged in, press the “power” button. Press the “wind speed” button to choose the gear, and then choose to turn on or off the negative ion generator. This mode is suitable for situations where compulsory purification is needed. The machine cannot change the gear automatically in this mode.
3. Night mode. In the two modes mentioned above, the machine will turn to work at the first gear as long as the “sleeping” button is touched, making sure there is no noise affecting your rest. (In auto mode, it will turn to sleep mode when the environment becomes dark, sensed by the photosensitive sensor)
4. Timing mode. In the three modes mentioned above, after the “timing” button is pressed and the operating time is set, the machine will start to count down. The machine will stop working after the countdown is finished. (If you need to cancel the countdown, please press the button until the time displayed is accumulated to 12 hours, then one more touch will cancel this mode).
5. Child-proof lock mode. In the four modes mentioned above, the machine will turn to childproof lock mode after the “child-proof lock” button is pressed. Any operation through the panel or the remote control will be invalid before quitting this mode. (It can be quitted by pressing the child-proof lock” button for 5 seconds or the unlock button on the remote control.)

Instructions for handling damage of the universal wheel

1. Universal wheels at the bottom, free to move, easy, and convenient.
2. If it is damaged and cannot be used normally, you can replace the screw fittings or the entire universal wheel fittings.

During Installation

1. Do not place in direct sunlight, facing air conditioner vents, or in heated places. It may cause the unit to warp, deteriorate, discolor, or malfunction.

• Do not place near TVs or radios. This may distort images or produce noise. Using the purifier remote may cause interference with your TV or radio. Please place at a distance of 1m or more away from these devices. In addition, if you are sharing outlets with these devices, plugging in the purifier may distort images or produce noise. If this happens, please plug the purifier into a different outlet.

1. The product must be placed on the floor for pollen and other indoor dust. Since such particles easily fall near the floor, we recommend placing the product on a flat surface on the floor.
2. For effective room circulation, place the product at approximately 30cm or more away from walls or other objects. Please keep the backside at least 20cm away from the wall to enable it to work more effectively.
3. Do not place items on the main unit or it may lead to malfunction. Be careful not to place magnets or any other metal items on here.
4. Do not block the exhaust vent or supply vent. For example, do not place an object on top of the exhaust vent or in front of the supply vent.

Prohibit

1. Do not pick up or move the machine while it is running. When moving or storing, do not pull the power cord. This may cause a short circuit or do internal damage to the power cord. This may lead to a fire or electric shock.
2. Do not damage the power cord or outlet. Do not cut, excessively twist, pull, or bend the power cord. If the power cord is damaged, for your safety please call the manufacturer, service department, or a trained professional to replace it.
3. Do not use power supplies, universal sockets, or connective devices that exceed the recommended power rating. Use only 110V- 5AAC power. Using a universal socket or connected power source that exceeds this rating may lead to overheating and cause a fire.
4. Do not touch the plug with wet hands. This may result in electrical shock.
5. Do not place your fingers or metal objects into the air vents. This may cause electrical shock or injury.
6. To avoid electrical shock or fire, do not allow water, flammable cleaners, or other liquids to enter the product.
7. This product cannot replace normal ventilation equipment, vacuum cleaners, or kitchen fans.
8. Please do not use this product near gas appliances, heating appliances, or stoves.
9. Do not use this product in a humid or hot environment, such as the shower, restroom, or kitchen.
10. Make sure the remote is placed somewhere children cannot reach to avoid unintended damage.
11. Do not place in the following locations:
12. Unstable places: this may cause the product to topple or fall down. This may lead to injury, electrical leakage, or fire.
13. Hot or humid places, such as the shower: this may result in electrical shock or fire due to electrical leakage.
14. Places like the kitchen emit fumes.
15. Do not use the air purifier in a room that is using an incense-type insect killer.
16. Chemical residue may accumulate in the machine and then be released, causing harm to physical health.
17. After using insect killer or mosquito coils, allow the room to be fully ventilated before using the air purifier.

Mandatory

1. Should any of the following conditions occur, turn off the machine immediately (electrical shock, sparks, or smoke may occur): Strange noises or vibrations during operation.
2. The product is unusually hot, or has a burnt odor.
3. Please clean the plug regularly If there is dust or moisture on the plug it could damage it. This may result in a fire
4. Unplug the power cord, and wipe it with a dry cloth.
5. Unplug the power cord if the appliance is not used for a long period of time.
6. Before electrical maintenance, make sure to unplug the device. The product may suddenly turn on, leading to electrical shock or injury.
7. Please plug the power cord securely into the power outlet. If the plug is not securely seated, this may cause overheating which may lead to electrical shock and even fire.
8. Do not use a damaged plug or loose power outlet.
9. Please unplug the cord using the plug insulator.
10. Pulling the power cord to unplug it may cause damage to the power cord, electrical shock, short circuit, or fire.
11. Should any of the following circumstances arise, please turn off the machine power immediately and contact the service department:
12. A switch does not work.
13. The power cord or plug IS unusually hot.
14. You detect an abnormal sound or vibration.
15. Any other abnormalities or malfunctions
16. To prevent the hazard of electrical shock, only trained professionals should disassemble the machine.

Filter/Dust SensorlAnion Producer Cleaning and Mainten

1. Pre-filter (approximately twice per month)
2. Clean the surface of the filter with a vacuum cleaner or wash with water. Allow drying thoroughly.
3. HEPA H13 composite high-efficiency filter (approximately once every two months)
4. Clean the dust from the front of the filter with a vacuum cleaner.
5. Place the filter in a ventilated area, this will allow harmful gasses and germs to dissipate. Do not place under too much sun exposure.
6. The filter is delicate.
7. Do not press too hard on the filter while vacuuming.
8. Do not use water to clean this filter.

Troubleshooting

Packaged Items

FCC STATEMENT

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device. pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and it not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not OCCur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment ana receiver,
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult thee dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>