Golden Vision H4 Smart Battery Video Doorbell User Manual
- June 5, 2024
- Golden Vision
Table of Contents
Thank you for using the smart doorbell camera
Basic Parameters
Product Name: Smart Doorbell Camera|
---|---
Pixel: 2 million pixels/ 3 million pixels| PIR human detection: Supports PIR
detection to wake up
Day and night conversion: dual filters automatically switch| Two-way talkback:
support full-duplex real-time calls
Local storage: Micro SD card| Wireless connection: 2.4G 802.11 b / g / n
Supported platforms: Android / iOS| Audio input / output: -38dB microphone /
speaker
Component Description:
Reset Button: Long press “reset” hole 5sec, reset success.
It is recommended to insert 8-128GB high-speed Micro SD card, otherwise, it
will not be able to store, view historical video and support Important
functions such as firmware upgrading.
Packing list: smart doorbell camera x 1, manual x 1, USB Power Cord screw
accessory package x 1
Install APP
Download APP: scan the QR code below to download and install. Register and log in: open the ” Smart Life” APP to register and log in according to the prompts.
http://smartapp.tuya.com/smartlife?from=singlemessage&isappinstalled=0
Add The Device-Scan QR code mode
- Make sure Wi-Fi is available and connected to the Internet.
- Connect the camera to the power, then system startup is completed.
- Open the “Smart Life” APP, press the’+’ in the upper right corner of the main screen (Figure 01); choose “Security & Video Surveillance”, dick “Smart Camera” (Figure 02) to add the camera; and then dick “Next step” (Figure 03);
Please note that only a 2.4 GH Wi-Fi network is supported;
-
If the mobile phone is not connected to please click “Connect to Wi-fi” (Figure 04);
-
It will jump to the WLAN interface and connects to Wi-Fi (Figure 05).
-
If the phone is connected to Wi-Fi (Figure 06);
-
A QR code will prompt on your screen and you need to scan it with the Smart Camera. (the camera is about 20-30 cm away from the mobile phone lens). Then click “hear the prompt sound” (Figure. 07.
-
connecting” (Figure. 08);
-
connection completed(Figure 09), and click “Done”;
-
Then jump to the preview interface (Figure 10)
-
After closing the device preview interface, the interface returns to the APP home page. At this time, the connected device will appear on the APP home page (Figure 11). Then you can click directly to the device interface to see the monitoring situation without re-adding afterward.
Add The Device-AP Mode
First set the machine to the hot spot distribution network mode
-
Locate the RESET button on the machine and press it for about 1 second, After about 1 minute, the sound will ring and the hotspot will start successfully.
-
Select “AP Mode” (Figure 12)
-
Click Next (Figure 13)
-
Enter the account and password that can connect to WIFI (Figure 14)
-
Click “Go Connect” (Figure 15)
-
Go to “Smart Life-XXXX “and click Connect (Figure 16)
-
Connecting (Figure 17)
-
connection completed(Figure 09), and click “Done”;
-
Then jump to the preview interface (Figure 10)
-
After closing the device preview interface, the interface returns to the APP home page. At this time, the connected device will appear on the APP home page (Figure 11). Then you can click directly to the device interface to see the monitoring situation without re-adding afterward.
Install
| 1. Wall drilling
---|---
2. Install the first base
3. Install the second layer base
| 4. Device power interface Wire connection on the back
---|---
5. Device power cord connection Tighten the connection with screw terminals
6. Screw on the screws under the bottom
Matters Need Attention
Try to keep away from the metal space ;
Avoid the furniture, microwave oven blocked;
Avoid the space where the audio, video, and data lines are wound, and keep the
space away from them as large as possible;
Ensure that as close as possible to the coverage of wireless Wi-Fi signals.
Switching network environment;
In the new network environment, please press the reset button for about 5
seconds, then connect to the network.
The name and content of the harmful substances in the product
Part
Name| Harmful Substance
---|---
Pb| Hg| Cd| Cr(VI)| PBB| PBDE
shell| 0| 0| 0| 0| 0| 0
Board| X| 0| 0| 0| 0| 0
charger| 0| 0| 0| 0| 0| 0
annex| 0| 0| 0| 0| 0| 0
This form is based on the provisions of SJ/T 113640
This product conforms to RoHS environmental protection requirements.
At present, there is no mature technology in the world to replace or reduce
the lead content in electronic ceramics. porcelain, optical glass, steel, and
copper alloy.
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by the manufacturer could void your authority to operate this
equipment. This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1)This device may not cause harmful
interference, and (2)this device must accept any interference received,
including interference that may cause undesired operation.
RF Exposure Information:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator &your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>