MAX-T RMS8101 IPX7 Electric Shaver User Manual
- June 5, 2024
- MAX-T
Table of Contents
MAX-T RMS8101 IPX7 Electric Shaver
General Information
Introduction
Thank you for your purchase. Please read this user manual as it contains information about the wonderful features of this shaver as well as some tips to make your shaving easier and more enjoyable.
Attention
Please read the user manual carefully before using this product, and keep it
for future reference.
- Close supervision is necessary when this shaver is used in the presence of children.
- To avoid injury, never use the shaver if there is any damage.
- The temperature range to operate, store and charge this product is 0 C~40 C.
- This product can be charged by a phone charger
- The shaver is designed to be IPX7 waterproof and can be washed directly under the water. It’s not suggested to immerse the shaver under water for a long time, which will reduce the life time of the shaver. Remember to check if the water is too hotto avoid scalding your hands.
- When you are on a trip, make sure the protective cover is on to protect the shaver heads. If there is a significant change in temperature, pressure, or humidity, please allow the shaver 30 minutes adaptation to new conditions before use.
- Use the USB charging cable in the package. Please connect the shaver to an AC outlet with 5V output or less, such as a phone charger or computer USB port.
Charging Instruction
-
Charging
When the shaver is charging, the LED displays will initially light on one by one and then turn off gradually. The remaining battery power status will be displayed by a percentage indicator. When battery power is less than 10%, the battery percentage indicating light will turn a flashing red. When it reaches over 10% capacity, the light will turn white and flash. When the shaver is fully charged, the light will stop flashing and remain steady. -
Full Charge
Fully charging the shaver requires 1 hour. This will give approximately 120 minutes of shaving time. When fully charged, the battery percentage indicating light will be always on. -
Low Battery
When the first indicating light turns a flashing red, the shaver requires recharging. -
Charging operation procedure:
- Connect the Micro USB port to the shaver charging port.
- Insert the USB plug into the USB charger.
- After the battery is fully charged, unplug the charger from the socket and then unplug the USB cable from the shaver.
-
Cleaning Tips
The cleaning indicator light will flash for 30 seconds if operational for Over 2 minutes, and it means cleaning is required. -
Traveling lock
Press the on/off button for 3 seconds. Lock mode is engaged when indicator lights flash. Please lock the shaver before carrying it on a trip to prevent the shaver from turning on unexpectedly.
Usage
Use the USB charging cable in the package. Please connect the shaver to an AC outlet with 5V output or less, such as a phone charger or computer USB port.
- Press the on/off button to turn on the shaver.
- The shaving heads flex to the contours of your skin. Your skin may need 2-3 weeks to adapt to the shaving system.
- Trimming sideburns: push the slider under the sideburn trimmer down to make the sideburn trimmer pop out.
- After shaving, press the on/off button to turn off the shaver; then put on a protective cover to prevent damage.
Cleaning & Maintenance
Important: Do not use compressed air, scouring pads, abrasive cleaning agents, petrol, acetone, and other corrosive liquid to clean the shaver.
-
You can rinse the shaver under the tap or clean it with a brush which is included in the package.
-
Be careful when using hot water. Always check the water temperature to make sure it is not too high to prevent scalding. Clean it each time after shaving to obtain the best shaving performance.
-
A damp cloth may be used to clean the outside of the shaver, but do not wipe the shaver blade parts with a towel or tissue, as this may damage the shaver blades as well as risk personal injury.
-
a: Switch off the shaver.
-
b: Press the release button, and open the shaving units.
-
d: Turn the locking device (A) by counterclockwise rotation, taking out the fixing rack (B).
-
e: Gently take out and clean the shaving heads one by one,
-
C: Pull out the shaver blades from the shaver being careful not to touch the blades. Each shaving head contains one shaver head blade and one guard.
-
f: Put the shaving heads back
-
Remove the blade from into the shaving units.
-
housing unit and use the brush Make sure the shaving head for cleaning.the recess portion is aligned with the recessed locations.
-
Make sure the shaving head recess portion is aligned with the recessed locations.
-
Insert the flange of the shaving unit into the slot at the top of the shaver, then close the shaving unit.
-
Put the fixing rack (B) back into the shaving units, then turn the locking device (A) clockwise.
Storage
Store with the protective cover on the shaving head to avoid damage.
Replacement
For the best shaving performance, we recommend replacing blades regularly. To replace the blades, follow the steps below:
- Switch off the shaver. Unplug from the electricity supply.
- Press the release button, and open the shaver head units.
- Pull out the shaving blade parts from the shaver.
- Turn the locking device (A) clockwise to remove the fixing rack (B).
- Remove the shaving blades, and put the new ones into the shaving unit
Environmental protection tips
When throwing away the product, please do not stack it together with other normal household waste. It should be handed over to an official designated recycling center that will be better for environmental protection.
-
Battery disposal
The built-in chargeable battery contains substances that may pollute the environment. When throwing away the shaver, the battery must be removed, then get it disposed at the official designated battery recycling center -
Remove the battery
To remove the battery only when you discard the shaver and make sure the battery is completely depleted. -
Detailed handling steps:
1. Disconnect the shaver from the electricity supply.
2. Switch on the shaver and run until all power is depleted.
3. Open the shaver head and unscrew the screws within the razor stubble storage compartment.
4. Remove the shell screw.Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>