MAX-T RMS7109 IPX7 Electric Shaver User Manual

: June 5, 2024
: MAX-T

Table of Contents

Structural Map
Introduction
Safety Warning
Charging
Using
Clean
Storage
Environmental Protection
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

RMS7109 IPX7 Electric Shaver
User Manual

Structural Map

MAX-T RMS7109 IPX7 Electric Shaver

Introduction

Please read this user manual, as it contains information about the wonderful features of this shaver as well as some tips to make shaving easier and more enjoyable.

Safety Warning

Please make sure the USB charging port on the bottom of the shaver is dry before charging.
Close supervision is necessary when this shaver is used in the presence of children or invalids.
Never use the shaver if there is any damage on it, or it may cause harm to the human body.
Never put the shaver directly into the sunlight or store it in a pouch at a temperature above 60 C/140 F.
The shaver is designed to be IPX7 waterproof, which can be washed directly under the water. It’s not suggested to sink the shaver under water for long time, which will reduce the lifetime of the shaver.
Please keep the protective cap on to protect the shaving heads after use.
A USB charging cable is included in the package. Keep the cord away from heated surfaces.
Use this shaver for its intended household use as described in this manual.

Charging

Preparation

Use the USB charging cable in the package.
Connect the shaver with an AC outlet(120V to 240V, 50/60Hz) with 5V output, such as a phone charger or computer USB connector.
Disconnect the cable after the shaver is fully charged.

Charging Status

When charging, the ﬁve LED displays will light on one by one.
When battery power is under 10%, the ﬁrst led light will turn red and ﬂash.
When the battery power reaches 10%, the red light will turn to white and ﬂash.
When reaches 20% capacity, the ﬁrst light will become always bright and stop the ﬂash immediately. Meanwhile, the second white light becomes ﬂashing.
When the shaver is fully charged, all ﬁve LED displays will always light to display full charge.

Full Charge
It will take about 1 hour for the shaver to be fully charged which can last approximately 120 minutes of shaving time.

Low Battery
The LED indicator will light out one by one along with the reduction of the battery capacity. When the ﬁrst indicator light turns red blinking, that means you need to charge the shaver.

Using

A. Press the switch button to turn on the shaver.
B. Shave against the direction of beard growth using both straight and circular movements.
C. Stretch your skin with your free hand so blades can lift and cut whiskers.
Gently press the shaver to the skin, so the ﬂoating heads can follow the contours of your face.
D. Trimming sideburns: push the slide-down key under the sideburns knife to make the sideburns knife pop out and trim sideburns beard. ( Your skin may need 2-3 weeks to adapt to the shaving system.)
E. After shaving, press the switch button to turn off the shaver.
F. Put the protective shaver head cap on the shaver to protect shaver heads.

NOTE: Please use shaving foam to get a better shaving experience. It the shaver is waterproof so that it can be used directly on wet skin and cleaned under a tap.

Clean

Important: Do not use compressed air, scouring pads, abrasive cleaning agents or petrol, acetone, or other corrosive liquid to clean the shaver.

You can rinse the shaver under the tap or clean it with a brush which is included in the package.
Be careful when using hot water. Always check the water temperature to make sure it is not too high to prevent scalding.
Clean it each time after shaving to obtain the best shaving performance.
Damp cloth is available to clean the outside of the shaver, but do not wipe the shaving blade parts with a towel or tissue, as this may damage the shaving blades.

|
---|---
A. Switch off the shaver.
B. Press the release button, and open the shaving unit.| C. Pull out the shave blade part from the shaver.
|
D. Turn the locking device (A) counter clockwise, and remove the retaining frame (B).| E.Remove and clean the shaving heads one by one. Each contains a set of shaver head cutters and a housing unit.
|
F. Clean inside and out with a clean brush grille.| G. Put the shaving heads back into the shaving unit.
|
H. Make sure the shaver head recess portion is aligned with the recessed portion.| I. Put the holder (B) back into the shaving unit, then turn the locking device (A) clockwise.
J. Put the ﬂange fork shaving unit into the slot at the top of the shaver. Then Close the shaving unit.

NOTE: If the shaving unit is closed sluggishly, check the shaving head to make sure it is inserted correctly and the holder is locked.