Shenzhen JM-VG01U GPS VEHICLE TERMINAL with GSM User Manual
- June 5, 2024
- Shenzhen
Table of Contents
Shenzhen JM-VG01U GPS VEHICLE TERMINAL with
GSM
Product overview
INS(Inertial Navigation System)
INS can be used as a fallback in weak or unavailable GPS signal area, e.g.
underpass, tunnel, downtown.
Driver behavior monitoring
Harsh acceleration alert
Harsh brake alert
Sharp tun alert
Harsh lane change alert
Crash alert
Loss of traction alert
Rolling alert
Vehicle angle abnormality
Position tracking
GPS&LBS positioning
Real-time location query
Easy self-installation
Specification
Package & Optional accessories
Product setup
LED indications
Wiring & Installation
Self-installation: If you choose device with 2-pin cable, it’s recommended to mount the device on the surface of vehicle battery.
- Select a proper installation place and stick the hook & loop on it. (To ensure GPS& INS tracking and driver behavior monitoring and to avoid GPS drift, please fix the device with the hook &loop.)
- Stick and fasten the device (back cover) on the other side of the hook& loop. Make sure device is faced up.
- Connect the red positive line to the positive terminal fastener of the vehicle battery.
- Connect the black negative line to the negative terminal fastener of the vehicle battery
6-pin power cable(Optional)
Specialized installation:
If you choose device with 6-pin cable, you can install the device inside the
car, close to the windshield.
Power connection
The standard power supply ranges from 9V to 36VDC. During installation,
negative side should connect to the ground. Do not connect with other ground
wires simultaneously.
ignition wire
ACC line (orange) connects to vehicle’s ACC, detecting ignition. Be sure to
check if it’s a real ignition wire i.e.power does not disappear after starting
the engine.
Relay wiring
Relay’s white line(85) connects to the positive side of battery(12V) while the
yellow line(86) connects to the device’s relay control x(yellow line on power
cord).
Find the fuel pump of the vehicle and cutoff its positive power line. The
positive side of fuel pump connects to the green line(87a) while the side
closing to starter motor connects to green line(30), as the below chart.
Switch of the two green lines have the same effect.
Installation recommendation
Tracked by mobile phone
- Send the command URL# by SMS to the device’s SIM card number.
- The device will reply with a map link. Clink the link to have the location displayed on Google Maps on your mobile phone.
- If device in somewhere not positioned, device will reply “Positioning.
- please wait for a moment or “Positioning fail”.
Monitored by tracking platform
- APN & Server setting To ensure normai network operation, please confirm your APN and server setting before you login. In most countries, APN could be automatically adapted to local mobile operators. If not, please send SMS to set the APN.
- If user name and password are required for APN, please add it into the command.
APN,apnnamer
E.g.APN, internet#
APN,apnname,user, pwd#
E.g.APN,internet, CLEMENTE,AMENA# Confirm the server address and setting with
distributors. If server is incorrect, please send SMS to change.
SERVER,mode, domain name/lPport, 0#
- E.g: SERVER,1, www.ydpat.com, 8011,0#
- SERVER,0, 211.154.135.113.8011,0#
- mode=1 means set with domain name
- mode=0 means set with IP address
- Please login the designated service platform and enjoy your monitoring experience.
GPS upload interval setting
- By time interval (Default Valid)
- TIMER,T1,T2#
- T1 means upload interval when ACC ON
- T2 means upload interval when ACC OFF
- Range: 5-18000 or 0 (second); 0 means no upload
- Default valid setting: TIMER,10,10#
- Query current TIMER setting: TIMER#
By distance interval (Default OFF)
DISTANCE,D#
D ranges 50-10000 or 0 (meters)
Note: When user enable uploading by DISTANCE, the preset TIME
uploading turns invalid.
SOS emergency call (with 6-pin power cable)
- In case of emergency case, press SOS for 3 seconds to activate SOS alert.
- The device will send SMS alert to preset SOS numbers and dial the numbers in a loop for three times until the call is picked up.
- Alarm message will also be sent to the tracking platform.
- To add SS number: SOS,A,number1,number2,number3#
- To delete the SOS number: SOs,D, phone number#
- Querv soS number: SOS#
Remote powerlfuel cut-off (with 6-pin power cable)
When vehicle is stolen, fuel/power command can be sent by platform,
APP or SMS.
Notice:
- Make sure ACC is correctly connected.
- When ACC is OFF, command will be executed immediately.
- When ACC is ON but GPS is not fixed, command will defer.
- When ACC is ON and GPS is fixed, command will be executed
- when vehicle speed is less than 20km/h.
- To cut-offrestore the fuel by SMS command, you have to authorize a center number.
- Set the center number: CENTER,A,mobile number#
- Delete the center number: CENTER,D#
Notice:
- Only the preset SOS number can set/delete the center number.
- Only one center number can be set.
- To cut-off fuel/power connection: RELAY,A#
- A=0/1 (0=restore fuel; 1=cut-off fuel) Default value:0
- E.g.RELAY, 1#
Over-speed alert (Default OFF)
SPEED,S,T,SPEED, M#
- S=1 means ON; S=0 means OFF
- T means duration of speeding, ranges 5-600 (second)
- SPEED ranges 1-255 (km/h)
- M means alert way
- M=1 SMS+GPRS; M=0 means GPRS
- E.g. SPEED,ON,20,100,1#
- When vehicle speed is over 100km/h for 10 seconds, you will receive
- SMS alert and GPRS alert on server.
Note: SPEED,OFF# Disable over-speed alert
Driver behavior monitoring
Device support detecting eight types of driver behaviors, which are transmitted by GPRS and can be displayed on the server.
-
Harsh acceleration alert
The device defines harsh acceleration as occurring when the vehicle speed increases sharply. An alert will be sent to the platform. E.g: The vehicle’s speed increase from OKM/H to 50KM/H after 2 seconds of engine start. -
Harsh brake alert
The device defines harsh braking as occurring when the vehicle’s speed decreases sharply. An alert will be sent to the platform. E.g: The vehicle’s speed drops from 50KMIH to 10KM/H after 2
seconds of emergency braking. -
Sharp turn alert The device defines a sharp turn as OcCurring when the vehicle makes a high-speed turn. An alert will be sent to the platform.
E.g: The driving speed is greater than 30KM/H, and the angle changes greater than 90 degrees. -
Harsh lane change alert The device defines harsh lanege as occurring when a vehicle suddenly change lanes at high speed. An alert will be sent to the platform.
E.9: The driving speed is greater than 60KM/H, and the angle change Is less than 20 degrees. -
Crash alerts collision occurs, the device will send an alert to the platform.
-
A slight impact and scratch will not trigger the alert. 6.Rolling alert When the vehicle’s rolling angle exceeds 70, the device will send alert to the platform.
-
Loss of traction alert When the vehicle changes the course angle for more than 3 seconds at an angular velocity greater than 20° /s, the device will sent a alert to the platform.
-
Vehicle angle abnormality When the vehicle’s rolling angle is greater than 20 and less than 70°, the device will send an alert to the platform.
FCC statements
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications or changes to this equipment. Such
modifications or changes could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the recelver is connected.
- Consult the dealer or an experienced radio/TV technician for help
When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements.
Troubleshooting
Warranty instructions
- The warranty is valid only when the warranty card is properly completed, and upon presentation of the proof of purchase consisting of original invoice indicating the date of purchase, model and serial No.of the product. We reserve the right to refuse warranty if this information has been removed or changed after the original purchase of the product from the dealer
- Our obligations are limited to repair of the defect or replacement the defective part or at its discretion replacement of the product itself.
- Warranty repairs must be caried out by our Authorized Service Centre. Warranty cover will be void, even if a repair has been attempted by any unauthorized service centre.
- Repair or replacement under the terms of this warranty does not provide right to extension or renewal of the warranty period.
- The warranty is not applicable to cases other than defects in material, design and Workmanship.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>