INSIGNIA NS-BK2TBS8 2-Tap Beverage Cooler User Guide

INSIGNIA NS-BK2TBS8 2-Tap Beverage Cooler

Product Information

The NS-BK2TBS8 / NS-BK2TBK8 kegerator is a 2-Tap Beverage Cooler designed for years of fun and trouble-free performance. It comes with a Quick Setup Guide to help you get your kegerator up and running quickly. For more detailed information, you can refer to the online manual located at www.insigniaproducts.com.

Package Contents

• Adjust temperature
• Change temperature unit
• Display
• Quick cool
• Quick Cool
• Quick Cool
• Before assembly
• Fill the CO2 tank (See your local beer keg provider, air/gas or welding supplier, or sporting goods store)
• Allow for space
• Do not use an extension cord
• You will need:
  • Pliers/clamp crimper
  • Phillips screwdriver
  • Adjustable wrench
  • Full kegs of beer (1/2 barrel size or smaller)

Product Usage Instructions

Assembling your kegerator

1. INSTALLING THE CASTERS (OPTIONAL)
2. Tip the kegerator onto its side on a soft surface to protect it from scratches.
3. Unscrew and remove the black front feet. Keep them in a safe place in case you want to use the feet later.
4. Attach the two metal washers (included) to the locking casters to prevent scratching the cabinet, then install the two locking casters in the front positions on the bottom of the kegerator (closest to the door).
5. Install the other two casters in the rear positions on the bottom of the kegerator.
6. With all four casters tightened evenly, stand the unit in the upright position.
7. Step on the front of the locking casters to lock the kegerator into place or step on the back to unlock the kegerator.
8. ATTACHING THE GUARD RAIL

Place the guard rail into the holes on the top of the kegerator.

1. INSTALLING THE DRAFT ARM ASSEMBLY
2. Remove the cabinet plug from the top of the kegerator.
3. Align the beer gasket to the four holes on the top of the cabinet.
4. Pass both the wing nut and the beer tube (both are attached to the draft arm assembly) through the hole on the worktop until the draft arm assembly is resting on the top of the cabinet.
5. Align the holes in the draft arm with the holes in the gasket, then attach the draft arm to the worktop with the four screws provided.
6. Attach the black plastic beer tap handles to the top of the faucet, tightening by hand. Hold the silver ring snug so it does not move.
7. INSTALLING THE CO2 REGULATOR & TANK

Note : The CO2 tank (provided) is empty when you receive it. Visit your local beer keg provider, air/gas or welding supplier, or sporting goods store to get it filled.
Caution : Before installing the CO2 regulator and tank, review important safety tips in the manual.

1. Feed the hose clamp over one end of the CO2 gas line.
2. Attach that end to the gas line connector on the CO2 regulator.

Congratulations on your purchase! Your NS-BK2TBS8 / NS-BK2TBK8 kegerator is designed for years of fun and trouble-free performance. This Quick Setup Guide is provided to help you get your kegerator up and running quickly. If you need more help, however, take a look at the online manual, located at www.insigniaproducts.com.

PACKAGE CONTENTS

1. Beer tap handles (2)
2. Draft arm assembly
3. Guard rail
4. Drip tray (2 pieces)
5. Worktop
6. Control Panel
7. Sankey Type-D keg coupler (2)
8. CO2 tank regulator
9. 5 lb. CO2 tank (shipped empty)
10. Bolt and nut for retainer
11. CO2 tank retainer
12. CO2 gas lines
13. Beer keg (not included)
14. Metal washers for locking casters (2)
15. Locking casters (2)
16. Beer gasket with screws (4)
17. Hose clamp
18. CO2 back tank retainer
19. Extra valve washers (2 of each)
20. Wire shelf
21. Wire half-shelf
22. Metal wrench (for cleaning)
23. Casters (2)

Before using your new product, please read these instructions to prevent any damage.

Before assembly

INSTALLING THE CASTERS (OPTIONAL)

1. Tip the kegerator onto its side on a soft surface to protect it from scratches.
2. Unscrew and remove the black front feet. Keep them in a safe place in case you want to use the feet later.
3. Attach the two metal washers (included) to the locking casters to prevent scratching the cabinet, then install the two locking casters in the front positions on the bottom of the kegerator (closest to the door).
4. Install the other two casters in the rear positions on the bottom of the kegerator.
5. With all four casters tightened evenly, stand the unit in the upright position.
6. Step on the front of the locking casters to lock the kegerator into place or step on the back to unlock the kegerator.

ATTACHING THE GUARD RAIL
Place the guard rail into the holes on the top of the kegerator.

INSTALLING THE DRAFT ARM ASSEMBLY

1. Remove the cabinet plug from the top of the kegerator.
2. Align the beer gasket to the four holes on the top of the cabinet.
3. Pass both the wing nut and the beer tube (both are attached to the draft arm assembly) through the hole on the worktop until the draft arm assembly is resting on the top of the cabinet.
4. Align the holes in the draft arm with the holes in the gasket, then attach the draft arm to the worktop with the four screws provided. 5 Attach the black plastic beer tap handles to the top of the faucet, tightening by hand. Hold the silver ring snug so it does not move.

INSTALLING THE CO2 REGULATOR & TANK
Note : The CO2 tank (provided) is empty when you receive it. Visit your local beer keg provider, air/gas or welding supplier, or sporting goods store to get it filled.
Caution : Before installing the CO2 regulator and tank, review important safety tips in the manual.

1. Feed the hose clamp over one end of the CO2 gas line.
2. Attach that end to the gas line connector on the CO2 regulator.
3. Tighten the clamp to prevent leaks. Leave about ½ inch between the top of the clamp and the end of the hose. You may need to squeeze with a pliers or crimper.
4. Attach the CO2 regulator to the CO2 tank by screwing the regulator nut onto the tank valve and tightening with an adjustable wrench.
5. Slide the CO2 tank through the retainer inside the kegerator and secure it with the bolt and nut. Position the tank so that you can read the numbers on the gauge and have easy access to the shut-off valve. OR
   Install the CO2 tank retainer on the back of the kegerator for extra space inside the unit. Refer to the manual for additional information.

INSTALLING THE KEG COUPLER
This kegerator accepts almost all brand name kegs. Here’s what will fit in your kegerator:

TIP : Keg sizes change so be sure to measure the inside of your kegerator and kegs to get a perfect fit.

*You can have a 1/4 (slim) and a 1/6, or a 1/4 (slim) and an 1/8 in your kegerator at the same time.

1. Insert the sankey keg coupler into the neck of the beer keg and turn it clockwise to lock it into position. Make sure that the washer is in the connector on the top of the sankey keg coupler.

2. Insert the beer tube into the top of the sankey keg coupler, then tighten the wing nut.

3. Repeat steps 1-2 if you have a second keg.

4. Pull the black handle on the sankey keg coupler and press it downward until it locks into position. The keg is now tapped.
   Note : If beer comes up through the top of the wing nut, remove the wing nut, reposition the washer, then reattach the wingnut.M

5. Insert the keg(s) into the cooler.

ADJUSTING THE CO2 REGULATOR

1. Make sure that the shut-off valve is closed (sideways if closed, down if open), then slowly turn the main valve on the CO2 tank counter-clockwise until it is fully open.

2. Open the shut-off valve to allow gas to flow into the keg.

3. Release the adjustment lock nut, behind the regulator screw, by turning it clockwise about 5-7 turns.

4. Turn the regulator screw clockwise to increase pressure. The needle on the gauge starts to climb. Set the gauge to 10-12 PSI.

5. When the tank is at the correct pressure, tighten the adjustment lock nut by turning it counter-clockwise.

6. Allow several minutes for the keg to pressurize. The gauge may show a drop in pressure while this happens. Adjust as needed.
   Note: Listen for a hissing sound at all connections to determine if there are any leaks.

7. Plug the kegerator into a 120V, 60Hz, 15A grounded outlet.

SETTING THE TEMPERATURE
See “Tips” for information about the best temperature for your beer type.

1. Press the °F/°C button to switch between Fahrenheit or Celsius.
2. Press – or + to adjust the temperature (32° to 50°F/0° to 10°C), then let the kegerator cool for 48 hours.
3. After the kegerator is fully cooled, press – or + to adjust to the temperature you want. The kegerator may take a few hours to stabilize after adjusting the temperature.
   Note: Press Quick Cool to cool the kegerator to its lowest setting. The icon appears and the kegerator cools for 24 hours. Press – or + to exit quick cool mode early. Cut this out and attach it to your kegerator for easy access to tips and help!

Tips

HOW TO GET A GREAT POUR
Pouring a proper glass of beer is very important, not only for presentation, but for taste.
TIP: Make sure your glassware is always clean and rinsed.

1. Hold the glass at a 45° angle.
2. Grasp the handle at the bottom and open the tap quickly.
3. Once your glass is half-full, gradually bring the glass upright, and aim for the middle to start forming the head. Slowly lower the glass as you approach your finish to improve the head even more.
4. When your glass is full, close the tap quickly.

USE DIFFERENT GLASSES FOR DIFFERENT BEERS
You wouldn’t believe how much a proper glass and temperature will change the taste of your beer.

PREVENTING BAD BEER

ONE-YEAR LIMITED WARRANTY

Visit www.insigniaproducts.com for details.

CONTACT INSIGNIA:
For customer service, call 1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its affiliated companies
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richfield, MN 55423 U.S.A.
©2017 Best Buy. All rights reserved.
Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>