Reese 44661 Jeep Compass Instruction Manual
- June 5, 2024
- REESE
Table of Contents
Reese 44661 Jeep Compass
Installation Instructions
Do Not Exceed Lower of Towing Vehicle Manufacturer’s Rating or
| Hitch type | Max Gross Trailer WT (LB) | Max Tongue WT (LB) |
|---|---|---|
| Weight Distributing | Do NOT Use With Spring Bars | |
| Weight Carrying Ball Mount | 3500 (1 589 Kg) | 525 (238 Kg) |
Hitch Shown In Proper Position
Equipment Required:
- Fastener Kit: 75712F
- Wrenches: 22mm, 16mm-tow hook option
- Drill Bits: 5/8”- Only needed to reinstall tow hook on Patriot with optional tow hook.
- Cutting Tool: Needed to trim bumper fascia on Compass Rallye and 2011 & later Patriot and Compass.
Note 1: Patriot with optional tow hook On Jeep Patriot with optional tow
hook on Driver’s side it is necessary to remove tow hook. Check with vehicle
owner
to see if they want tow hook reinstalled. To reinstall hook it is necessary to
press/drive existing knurled neck bolts out of hook and drill out with 5/8”
drill. Reinstall hook by using supplied M14 bolts following steps below.
- Qty. (4): M14 x 120 x 2 Hex Bolt
- Qty. (2): 5/8” Lock Washer
- Qty. (2): 5/8” Conical Washer
- Qty. (4): M14 x 2.0 hex Nut
NOTE: Lowering exhaust may ease installation. To lower exhaust, remove
rubber hanger from hanger bracket. Spraying a lubricant or soapy water on the
metal hanger rod and the rubber isolator helps removal. Some vehicles have a
carbon canister installed on the driver side frame rail. The canister, if
needed can be lowered allowing for additional clearance during the install.
NOTE: If vehicle has optional tow hook see Note 1. above. 2007-10 Models:
Only Rallye edition require fascia trimming Compass Rallye.
Jeep Patriot and Compass models 2011 and later. Fascia trimming is required for hitch installation. See Figure 3 and Figure 4 for fascia trimming Obtain vehicle owners approval before cutting.
- Place M14 hex bolts into vehicle bushings from the outboard side of the vehicle frame rails. Leave bolt ends flush with the inboard side of frame rails.
- Raise hitch into position and push M14 hex bolts through hitch frame brackets to support the hitch.
- Attach remaining hardware as shown above.
- On Compass Rallye Package only. Use hitch receiver tube as a guide to cut a 2-1/4” wide by 2” high piece out of bumper fascia to allow clearance for ball mounts. See Figure 2.
- Raise exhaust back into position if lowered prior to hitch installation.
Note1: check hitch frequently, making sure all fasteners and ball are
properly tightened. If hitch is removed, plug all holes in trunk pan or other
body panels to prevent entry of water and exhaust fumes. A hitch or ball which
has been damaged should be removed and replaced. Observe safety precautions
when working beneath a vehicle and wear eye protection. Do not cut access or
attachment holes with a torch. This product complies with safety
specifications and requirements for connecting devices and towing systems of
the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
Note 2: Compass Rallye Package It is necessary to trim bumper fascia.
Obtain vehicle owners approval for cutting plastic fascia before installing
hitch! See diagram.
Fascia Trimming Diagram for 2011 & Later Jeep Patriot and Compass Models
*2011 and Later Jeep Patriot and Compass models require fascia trimming for hitch installation. Obtain vehicle owner approval before cutting.
from ground to bottom
of frame) must be measured to double check placement of cut. X-5 inches is the
distance measured from the ground to the top of the fascia cut
Note: check hitch frequently, making sure all fasteners and ball are
properly tightened. If hitch is removed, plug all holes in trunk pan or other
body panels to prevent entry of water and exhaust fumes. A hitch or ball which
has been damaged should be removed and replaced. Observe safety precautions
when working beneath a vehicle and wear eye protection. Do not cut access or
attachment holes with a torch. This product complies with safety
specifications and requirements for connecting devices and towing systems of
the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>