METRAVI VT-145 Machine Condition Monitor with Vibration Tester Instruction Manual
- June 2, 2024
- METRAVI
Table of Contents
METRAVI VT-145 Machine Condition Monitor with Vibration Tester
Product Information
Technical Specifications
- Input: Vibration measurement
- Accuracy: +/-5%
- Alarm Indication: Temperature Accuracy
- Resolution: Display Power & Charger
- Operating Temperature: Range
- Dimensions: 115 x 75 x 25mm (LxWxT)
- Weight: 230g
- Accessories: Acceleration sensor, Magnetic holders for sensors, Probe, Battery Charger, User Manual, Carrying Case
Product Usage Instructions
Vibration Measurement
The VT-145 machine condition monitor with vibration tester is equipped with
a 100mV/g IEPE acceleration sensor and an 80cm cable with a BNC connector for
input vibration measurement.
Display and Operation
The device features a TFT color display with a resolution of 128×160 pixels
for clear visibility. The menu options and readings are easy to navigate and
understand.
Power and Charging
The VT-145 is powered by a lithium rechargeable battery with a capacity of
3.7V 1600 mAh. The device can operate continuously for over 30 hours on a full
charge. The recharge time for the battery is approximately 3 hours.
Operating Conditions
The recommended operating temperature range for the VT-145 is [Specify
Operating Temperature Range here]. Ensure the device is used within this
temperature range for optimal performance.
Accessories
Make use of the provided accessories including the acceleration sensor,
magnetic holders for sensors, probe, battery charger, user manual, and
carrying case for convenient usage and storage of the VT-145.
Frequently Asked Questions (FAQ)
-
Q: What is the operating temperature range for the VT-145?
A: The operating temperature range for the VT-145 is [Specify Operating Temperature Range here]. -
Q: How long does the battery of the VT-145 last on a full charge?
A: The lithium rechargeable battery of the VT-145 can operate continuously for over 30 hours on a full charge. -
Q: What are the included accessories with the VT-145?
A: The included accessories are acceleration sensor, magnetic holders for sensors, probe, battery charger, user manual, and carrying case.
INTRODUCTION
The Metravi VT-145 Machine Condition Monitor with Vibration Tester is a
handheld instrument based on the latest microprocessor design. It can measure
Vibration, Infrared Temperature and features intelligent colour alarm
functions.
The instrument is simple and easy to use, suitable for on-site machine
operation and maintenance inspector to monitor machine condition, detect
problems in time, and ensure reliable operation of machines.
VIBRATION MEASUREMENT
The Metravi VT-145 can measure the effective value of Vibration Velocity (mm/s
RMS), Single Peak Acceleration (g P), Peak-to-Peak Displacement (um P-P) and
high-frequency Acceleration value (BG Peak).
When measuring velocity, the instrument will automatically determine and
indicate the machine alarm status
in colour based on the built-in ISO10816-3 machine vibration standard.
TEMPERATURE MEASUREMENT
In addition to its vibration detection function, the Metravi VT-145 is also
equipped with a non-contact Infrared Thermometer, which is mainly used for
checking bearing temperature. The measuring range is -20°C ~ 120°C, and the
measuring position is indicated by a red laser pointer.
STANDARDS
ISO10816-3 VIBRATION STANDARDS
Support classification: R-rigid support F-flexible support
Machine classification:
-
Group 1: Large machines with rated power ≥300KW; motors with shaft height ≥315mm.
Usually sliding bearing, rotation speed 120RPM – 15000RPM -
Group 2: motors with rated power 15KW≤P<3 00KW; shaft height 160≤H<3 15 mm.
Usually with rolling bearings, speed >600RPM -
Group 3: Pumps with rated power >15KW, multi-blade impeller and separately connected to the prime mover
(Centrifugal, mixed flow, axial flow). -
Group 4: Pumps with rated power >15KW, multi-blade impeller and integrated with the prime mover (Centrifugal, mixed flow, axial flow)
ISO10816-3 INTERNATIONAL STANDARD FOR MACHINE VIBRATION
ISO10816-3 is a special standard for measuring vibration intensity on machine
bearings, bearing seats or supports. This vibration standard is applicable to
units with a power greater than 15KW and an operating speed of
120-15000rpm, including the following machines:
- Steam turbines with power not exceeding 50MW
- The power of the steam turbine unit is greater than 50MW, and the rotation speed is lower than 1500rpm or higher than 3600rpm units included in ISO10816-2)
- Rotary compressor
- Industrial gas turbines with power not greater than 3MW
- Centrifugal, mixed flow or axial flow pumps
- Generators other than hydraulic generating units or pumping stations
- Various types of electric motors
- Blower or fan
ISO10816-3 VIBRATION VALUE STANDARD EVALUATION
Suitable for industrial machines with power greater than 15KW and rated speed
of 120-15000RPM.
TECHNICAL SPECIFICATIONS
- Input 100mV/g IEPE acceleration sensor, 80cm cable and BNC connector
- Vibration measurement
- Velocity: 0-200mm/s
- RMS Frequency 10Hz-1kHz
- Displacement: 0-2000μm
- Peak-Peak Frequency: 10Hz-1kHz
- Acceleration: 0-20 g
- Peak Frequency: 10Hz-1kHz
- High frequency acceleration 0-20 g peak frequency range 1 kHz~12 kHz
- Accuracy: +/-5%
- Alarm Indication Built-in ISO10816-3 machine vibration standard evaluation of vibration speed alarm state
- Temperature -20~120°C with laser dot target indication
- Accuracy ±2°C
- Resolution 1°C; D:S 8:1
- Display TFT colour display, 128×160 pixels
- Power & Charger Lithium rechargeable battery, 3.7V 1600 mAh Recharge time 3 hours; Operating time >30 hours continuous
- Operating Temperature -10°C to +50°C
- Dimensions 115 x 75 x 25mm (LxWxT)
- Weight 230g
- Accessories Acceleration sensor (with 80cm length cable), Magnetic holders for sensors. Probe, Battery Charger, User Manual, Carrying Case
Setting Trends. Showing the Way.
www.metravi.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>