HIKVISION UD21052B Face Recognition Terminal User Guide

HIKVISION UD21052B Face Recognition Terminal

Appearance

Installation

Installed on Environment

1. Avoid backlight, direct sunlight, and indirect sunlight.

2. For beer recogni on, there should be light source in or near the installa on environment.

3. If you have to install the device outdoors, you should install a protec ve shield(op onal) for the device.

4. Secure the moun ng plate on the base plate with 4 screws.
   Remove the sponge tage on the base plate and secure the device on the moun ng plate with 2 screws.

5. Secure the decora on plate on the base plate with 4 screws.S ck 3 waterproof membranes on the decora on plate as shown below. Route the cable through the cable hole of the plates, and connect to external device’s cables.

6. Dig a hole (242 mm × 114 mm × 30.5 mm) on the wall. Place a gang box in the hole (a), and remove the 4 moun ng ears with tool (b).
   Secure the combina on and the gang box with 1 screw (c).

7. The gang box is op onal. You should purchase it separately.

8. The waterproof membranes is used only in the flush moun ng.

9. For surface moun ng, see the user manual.

Wiring (Normal)

Use only power supplies listed in the user instruc ons:

• When connec ng door contact and exit buon, the device and the RS-485 card reader should use the same common ground connec on. The Wiegand terminal here is a Wiegand input terminal. You should set the device’s
• Wiegand direc on to “input”. If you should connect to an access controller, you should set the Wiegand direc on to “Output”. For details, see the user manual.
• The suggested external power supply for door lock is 12 V, 1 A.
• The suggested external power supply for Wiegand card reader is 12 V, 1 A.
• For wiring the fire system, see the user manul. Do not wire the device to the electric supply directly.
• If the device support PoE, the network interface supports power supply by PoE.
• If the device supports power supply by PoE and the network interface is connected, do not wire the power input terminal.

Wiring (With Secure Door Control Unit)

Quick Operation

Activation
Power on and wire the network cable after installation. you should activate the device before the first login.
If the device is not activated yet, it will enter the Activate
Device page after powering on.
Steps:

1. Create a password and confirm the password.
2. ap Activate to activate the device. For other activation methods, see the device user manual.
   • We highly recommend you to create a strong password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security System, changing the password monthly or weekly can better protect your
     product.

Set Application Mode
After activation, you should select an application mode. Select Indoor or Others from the drop-down list and tap OK. If you install the device indoors near the window or the face recognition function is note working well,
select Others.

Set Language
Select a language from the drop-down list.

Set Network Parameters
Wired Network:
If enable DHCP, the system will assign the IP address and other parameters automatically.
If disable DHCP, you should manually set the IP address and other parameters.
Wi-Fi:

• Select a Wi-Fi and enter the Wi-Fi’s password.
• Or tap Add Wi-Fi and enter the Wi-Fi’s name and password.
• If you select Wired Network, make sure the device has connected toa network.

Link to Mobile Client
Download and install the mobile client. Use the scan QR code function of the mobile client and scan the QR code on the device to link the device to the mobile client. Set Administrator
Steps:

1. Enter the administrator’s name and tap Next.
2. Select a credential to add. You can select face, fingerprint, or card.
3. Tap OK.

Add Face Picture

1. Use finger to hold the screen surface for 3s and slide to right/left and enter the activation password to enter the Home page.

2. Enter the User Management page, tap + to enter the Add User page.

3. Set the user parameters according to actual needs. Only the device with the fingerprint module support the finger print related functions.

4. Tap Face and add the face information according to the instructions. You can view the captured picture on the screen, Make sure the face picture is in good quallity and size. For details about the tips and positions when collecting or comparing the face picture, see the contents on the right.

5. If the picture is in good condition, tap the 2 Or tap theto talke another face picture.

6. Tap the save icon to save the settings. Go back to the initial page to start authentication. For other authentication methods, see the device user manual. User other authentication methods if the device is affected by the
   light or other items.

7. N Matching: The device will compare the captured face picture with the ones in the database.

8. Matching: The device will compare the captured face picture with the user linked face picture.

Tips When Collecting/Comparing Face Picture

Expression

• Keep your expression naturally when collecting or comparing face pictures, just like the expression in the picture on the right.
• Do not wear hat, sunglasses, or other accessories that can affect the facial recognition function.
• Do not make your hair cover your eyes, ears, etc. and heavy makeup is not allowed.

Posture

In order to get a good quality and accurate face picture, position your face looking at the camera when collecting or comparing face picture

Size
Make sure your face is in the middle of the collecting window.

Regulatory Information

FCC Information

Please take attention that changes or modifications not expressly approved by the party responsible for compliance Cv easy.prepare e f pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Ihis equipment generates, usSes and can radlate radio Frequency energy ana, if not installed and used in accordance With the instructions, may cauSe narrow interference to radi0 communications. However, there is no guarantee that interference will not occur in a particular installation. If this d found to comply with the limits for a Class B digital device the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment anareceiver
• Consult the dealer or an experienced radio/TV technician for help.
• This equipment should be installed and operated with a minimum distance 20cm between the radiator and your that to which the receiver is connected.

Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
2. This device must accept any interference received, including interference that may cause undesired operation.

References

• Hikvision - Leading Video AIoT Solutions & Services Provider
• HOME

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>