weg SSW900-HMI-BLT Bluetooth Graphic HMI Installation Guide
- June 5, 2024
- weg
Table of Contents
SSW900-HMI-BLT Bluetooth Graphic HMI
Installation Guide
SAFETY INFORMATION
1.1 SAFETY WARNINGS
NOTE!
Only use the SSW900-HMI-BLT Bluetooth on WEG soft-starters of the SSW900
series.
It is advisable to read the SSW900 user manual before installing or operating
this accessory.
This manual contains important information for the full understanding and
proper operation of the HMI.
1.2 PRELIMINARY RECOMMENDATIONS
DANGER!
Always disconnect the general power supply before touching any electrical
component connected to the SSW900 soft-starter.
High voltages may still be present even after disconnecting the power supply.
Wait for at least three minutes to ensure the complete de-energization of the
soft starter.
Always connect the equipment frame to the protective earth (PE) at the proper
terminal.
ATTENTION!
Electronic boards have components sensitive to electrostatic discharges.
Do not touch the components or connectors directly. If necessary, first touch
the grounded metallic frame or wear a grounding strap.
GENERAL INFORMATION
2.1 ABOUT THE MANUAL
This guide provides directions for the installation, configuration, and
operation of the SSW900-HMI-BLT.
The SSW900-HMI-BLT accessory has one USB and a Wireless Bluetooth port.
2.2 PACKAGE CONTENT
Upon receiving the product, check if the package contains:
Accessory in the anti-static package.
Installation, configuration, and operation guide.
2.3 RECEIVING AND STORAGE
The SSW900-HMI-BLT is supplied and packed in a cardboard box.
A label is affixed to the package, identical to the one affixed to the SSW900
-HMI-BLT.
In order to open the package:
- Place the package on a table.
- Open the package.
- Remove the SSW900-HMI-BLT.
Check if:
- The identification label of the SSW900-HMI-BLT corresponds to the purchased model.
- Damages occurred during transportation. If any problem is found, contact the carrier immediately.
- If the SSW900-HMI-BLT is not installed soon, keep it in the package closed, and store it in a clean and dry location with temperatures between -25 ºC and 65 ºC (-13 ºF to 149ºF).
Table 1: Package dimensions in mm (in)
Height H mm (in)| Width L mm (in)| Depth P mm (in)| Volume
cm³ (in³)| Weight kg (lb)
---|---|---|---|---
150 (5.90)| 80 (3.15)| 70 (2.76)| 62,92 (3.84)| 0,2 (0.44)
2.4 ABOUT THE SSW900-HMI-BLT
The SSW900-HMI-BLT enables the user to view and program the entire SSW. Its
navigation method is similar to the one used in cell phones, with access to
all the parameters in groups (Menu). USB and Wireless Bluetooth communication.
| USB connector for communication with PC.
---|---
| Cancels programming. Go back to the menu.
| Shows help text for the marked content.
| Increments and decrements values. Navigation in the menu system.
| Changes the main screen. Moves within values. Navigation in the menu system.
| Enter key: Save the change. Enter the menus.
| Control of the motor direction of rotation, if programmed for HMI.
| Selects LOCAL or REMOTE command, if programmed for HMI.
| JOG, if programmed for HMI.
| Stops motor, if programmed for HMI. Fault reset.
| Stops motor, if programmed for HMI.
INSTALLING THE SSW900-HMI-BLT
This chapter describes the electrical and mechanical installation procedures
for the SSW900.
3.1 INSTALLING THE SSW900-HMI-BLT
3.1.1 Environment Conditions
The location of the SSW900-HMI-BLT is a determinant of its proper operation
and for ensuring the service life of its parts.
Avoid:
- Direct exposure to sunlight, rain, excessive moisture, or marine environment.
- Inflammable or corrosive liquids or gases.
- Excessive vibration.
- Dust, metallic particles, or oil mist.
Allowed Environment Conditions:
- Temperature: rated conditions.
- -10 ºC to 55 ºC (14 ºF to 131 ºF).
- Air relative humidity: 5 % to 90 % non-condensing.
- Maximum altitude: 4000 m (13123 ft) above sea level – rated conditions.
- Pollution degree: 2 (according to UL508). Normally, only non-conductive pollution. Condensation must not cause conduction through the accumulated residues.
3.1.2 Installing the SSW900-HMI-BLT on the SSW900
3.1.3 Installing the SSW900-HMI-BLT on the Panel Door
For panel door mounting, use an HMI Frame Kit according to the required cable
size.
Table 2: Accessory models
Item | Name | Description |
---|---|---|
13469204 | SSW900-KMD-CB01 | HMI Frame kit + 1 m cable |
13466665 | SSW900-KMD-CB02 | HMI Frame kit + 2 m cable |
13469206 | SSW900-KMD-CB03 | HMI Frame kit + 3 m cable |
13469207 | SSW900-KMD-CB05 | HMI Frame kit + 5 m cable |
13469208 | SSW900-KMD-CB07 | HMI Frame kit + 7.5 m cable |
13469209 | SSW900-KMD-CB10 | HMI Frame kit + 10 m cable |
1346 9211 | SSW900-KMD-CB20 | HMI Frame kit + 20 m cable |
WEG WPS APP
4.1 INSTALLATION
WEG WPS app is available at Google Play Store for the Android version or App
Store for the iOS version.
4.2 PAIRING OF THE BLUETOOTH HMI
When connecting a Bluetooth device to the SSW900-HMI-BLT for the first time,
you should pair the SSW900-HMI-BLT with the device.
NOTE!
Because of RF emissions and legislation in force in each country, Bluetooth is
disabled at the factory. C8.6 Bluetooth, C8.6.1 Mode = 0 = Inactive, change to
1 = Active.
The default number for the PIN (Personal Identifying Number) is 123456.
C8.6.2 PIN = 123456.
C8.6.3 Device Name = SSW9x + product serial number.
The values can be changed in the communication parameters of the product.
NOTE!
In some devices, to use the WEG WPS application, enable the GPS of your cell
phone.
4.3 USING THE WEG WPS SOFTWARE
After the successful pairing, different functions can be used for the WEG
Drives configuration tool:
- Parameter setting.
- Parameter backup
- Trend.
- Reading of logs (faults, alarms, events).
- Oriented start-up.
- Wi-Fi and Bluetooth communication.
CERTIFICATIONS
This chapter presents the product certifications.
NOTE!
Check which standards and certifications are required in your country and
whether the product is homologated for use.
5.1 ANATEL Homologation Number: 007921907908
Technical Compliance Certificate: 6575
https://www.anatel.gov.br/paineis/certificacao-de-produtos/consulta-de-
produtos
5.2 FCC
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE!
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FCC ID: S9NSPBTLERF.
5.3 CE
Hereby, WEG Drives & Controls – Automação Ltda declares that the radio
equipment type SSW900 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address: www.weg.net.
- Frequency band: 2400 MHz – 2483,5 MHz.
- Maximum power: < 10 dBm.
Evaluation report: 266728-TL7-2.
ID number of the certificate: 40051099.
VDE file reference: 5015068-5980-0002/266728.
Document: 10007737519 / 00
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>