HEYMELL Voyage 202 2.0 Channel Soundbar User Manual

Voyage 202(White Noise Version)
Voyage 203(Standard Version: Without White Noise)
2.0 Channel Soundbar
User Manual

Thank you for purchasing Heymell Soundbar Voyage2O2. This guide will help you set up so you can enjoy the ultimate sound experience.

1. Power Adapter
2. Optical Cable
3. 3.5mm Audio Cable
4. Wall Mounting Bolts
8. Wall Mounting

DIAGRAM (BUTTONS, PORTS & INDICATOR)

1. Press “ ” 0.5 seconds to switch on, and hold for 3 seconds to turn off. While turning on, short press the button, and switch the input source among Bluetooth, HDMI ARC, Optical, AUX, Coaxial, and USB.
2. “ ” button: USB and Bluetooth mode, Short press to Ile ” Play/Pause’; Bluetooth mode, Long press to disconnect current Bluetooth, entering the pairing status; Optical /ARC /Coaxial /ARC mode, short press to switch ” ON/OFF ” of mute.
3. Volume “ + “: Short press for increasing volume “ +1 ” each, hold and long press to next song.
4. Volume “ – “: Short press for decreasing volume ” -1 ” each, hold and long press to the previous song.
5. LED Indicator: Bluetooth Input : , Optical Input : , HDMI ARC Input : , Coaxial Input : , Aux Input : , USB Input :
6. HDMI ARC Input
7. Optical Input
8. Coaxial Input 0
9. 3.5mm Audio Input

Table placement

1. The remote of the TV is infrared, don’t cover the receiver window of the TV, or select the wall mounting.
2. The free space with length and width will be enough to place the soundbar.

Wall Mounting

1. Remove 4 screws as shown 1.
2. Secure the hardware wall bracket 2 in the accessory box with the screw you just removed and lock it in the position as shown 1.
3. Follow steps 3-6 in the following illustration and hang the main soundbar on the wall.

REMOTE CONTROL

Battery installation

Remark (2PCS AA Battery)

1. Install a power enough battery, better new battery
2. The working range of the remote is +/- 30° in both vertical and horizontal directions.

Instructions for the remote control key.

1. Power: Press the key” “ (1/ 1) for 1s to switch on, hold for 3s to turn oft

2. Mute Press the key” “ (2/2) to enter the mute state, and press again to exit.

3. Select Inputs (3/3): Short press ” BT” to enter Bluetooth, in Bluetooth mode, hold about 3S to disconnect the Bluetooth connection. Short press “ARC/COA” Key to be ARC, hold about 3S to be COA. Short press “AUX/USB” to be AUX, Hold about 3S to be USB.

4. Adjust Treble Volume (4/4): The treble will increase or decrease by 1dB by pressing ” TREBLE+ /-” each time.

5. Adjust Bass Content (5/5) : The Bass content will increase or decrease 1dB by pressing “BASS+/-” each time.

6. The key “ “(6/6): USB and Bluetooth mode, short press to play/pause;

7. Four Different EQ Mode (7/7): MUSIC MOVIE, NEWS, GAME, show” “.
   MUSIC: For Pop Music and TV Shows without heavy bass
   MOVIE: For Movie, especially Movie with heavy bass
   NEWS: For News, Talk shows, and Variety shows, hold or short press the key ” NEWS” ( Voyage 202), hold the key “MOVIE/NEWS” ( Voyage 203).
   GAME: Specific game sound effects.
   RESET(Voyage202): Short press or hold the Key ” RESET ” to reset the value of “BASS+/-“, and “TREBLE+/-” to be the default.
   RESET(Voyage203): Hold the Key ” RESET ” to reset the value of”BASS+/-“, and “TREBLE-Fr” to be the default.

8. For power on status, press ” 3D /LED OFF ” (8/8) to switch 3D to be ” ON ” or ” OFF “. standby or power off status, press the key to switch the LED light to be ” OFF ” or ” ON “.

9. White noise mode: Sleep Aids MP3 Function. If you have difficulty sleeping, you can choose white noise in different scenes to help you sleep better. (Only for Voyage 202)

10. A total of 11 different white noises are included.] Pure White Noise, 2 Ocean Wave, 2 Fan Noise, 1 Bird Song, 2 Cricket Sound, 2 Raining Sound, and 1 Brown Noise.

11. Press any key ( index 9 ) to enter the white noise mode.

12. For white noise mode, switch the key to preview and select your satisfied sound.

13. Press the time key “15/30/60/90 ” to select the white noise playback time, the unit is minute. Press once to switch the playing time once.

14. During playback, you can switch to other white noises. If the timer key is not pressed, the original set time will continue to play until the end of the preset time; if the timer key is pressed again to select a new timer, the timer will restart;

15. After the timer ends, the soundbar will automatically shut down without affecting sleep.

16. After the white noise timer is played, if any input mode (Bluetooth, ARC, Optical, Coaxial, AUX, USB) is selected, the white noise mode will be exited.

17. There is no memory function for the white noise setting. After a timer ends or after turning off the machine, you need to perform the operation again according to the above steps.

USING YOUR SOUNDBAR

A. Turn ON/OFF

B. Connect to your TV

Use Remote Control or Button of Soundbar to change input models.
Note:

1. Prior to use, check if your TV has HDMI ARC, Optical, Coaxial, and Aux Stereo Audio Output;
2. Prior to using the HDMI ARC connection, please be sure that the HDMI port of your TV support ARC and that the HDMI ARC cable version is not lower than HDMI 1.4;
3. Turn on the PCM settings of your TV when connected in Optical / Coaxial / Aux mode in case it doesn’t have sound. And you can get the detailed support from the ” Quick Guide Manual “;
4. 32 is the maximum volume of the soundbar.

C. Connect to other devices

Need to purchase one 3.5mm RCA Audio Cable if your device has L/R RCA audio output, the included stereo audio cable will not fit.
D. Bluetooth Connection

Short press “BT” on the remote control or switch the” “key on the soundbar, and it will enter Bluetooth mode.” “will flash when pairing,” “will be stable when connected successfully.

Specification

Model No. : Voyage 202 (White Noise Version), Voyage 203 (Standard Version, without White Noise)
Sound Channel: 2.0
Distortion: 1%
Power Supply: DC 21V **1.7A
Speakers Drivers: 2.25″ 4 PCs Full-Range Drivers
Functional Output: HDMI ARC 1, Optical 1, Coaxial 1, Aux 1, USB 1
Packing Size: 918180128mm/ 36.147.095.04 Inches
Weight:** 2.2 Kg / 4.85 Lbs; G.W., 3.0 Kg / 6.61 Lbs

Safety Instructions

1. Avoid dropping
2. Do not disassemble
3. Avoid extreme temperatures
4. Don’t use the device outdoors during thunderstorms
5. Use original or certified cables
6. Don’t use any corrosive cleaner/oil to clean
7. The products should not be exposed to dripping or splashing water

FCC Regulatory Compliance
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, this is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver,
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
RF Exposure Compliance
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Supplier’s Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Unique Identifier Trade Name: Heymell, Model No. : Voyage 203
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
This mark shown on the product or its packaging indicates that this product should not be disposed of with other household waste at the end of its working life.
To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of waste and recycle it responsibly to promote the sustainable reuse of material resources.
Household user should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their suppliers and check the terms and conditions of the purchase contract. This product Should not be mixed with other commercial wastes for disposal.
IC STATEMENT
This device complies with Industry Canada’s license-exempt RSS. Operation is subject to the following two conditions:

1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

@HeymellS
@Heymell.Service
****Heymell.Service@joyeaest.com
ICID: 28001V0Y203
Designed By Linghuixin(Shenzhen) Co., Ltd.
MADE IN CHINA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>