FIIL T1 XS True Wireless Earbuds User Manual

June 5, 2024
Fiil

FIIL T1 XS True Wireless Earbuds User Manual

Packaging Content

Main User Interfaces

  • Earbud
  1. Earwing
  2. LED indicator
  3. ENC microphone
Charging Case
  1. Charging Case Cover
  2. D Left earbud
  3. Right ea rbud
  4. Charge indicator
  5. Type-C connector

Get Started

STEP l

If charging case’s LED does not light on after open the charging  case at first, please connect USB cable to charge more than

STEP 2

Open the charging case then earbuds will automatically get sync and enter pairing mode without any manual operation.

Notes: Please charge the charging case via USB adapter in advance

Bluetooth Pairing

Bluetooth pairing
For first usage of brand new FIil Tl XS, please refer to pages “Get Started”, the earbud status indicator will continue to blink blue once entered pairing mode.
Fora paired FIil Tl XS, please delete its pairing history in the device list or when the earbuds are turned off, press and hold any one of earbuds until the LED indicator blinks blue.

Search Connection

Enter setup rnenu of audio source devices, select “search device” in “Bluetooth” then select “FIil Tl XS” in the device list to connect.

Earbuds Sync

Auto-Sync
Please refer to pages “Get Started”, the left and right earpbuds will automatically get synced after Step2.
Manual Sync

Step 1-

Power Off Earbuds Press and hold both earbuds at the same time, do not release your fingers until both red lights are on for 3 seconds.

Step 2 – Reset Sync

Press and hold the earbuds again, do not releaseyourfingers until the purple light is off.
Note: Please hold your finger until purple light and ignore all other lights during above process.

Step 3 – Reconnect Bluetooth

Put earbuds back in the charging case and close it;
(%) Delete the “FIil Tl XS” in your bluetooth device list; Repeat the “Search Connection” in Bluetooth Pairing(Page 6);. Notes: If a purp[e lignt comes on in earbud during@, please do not connect Bluetooth but repeat G) and  wait a little lpnger, or repeat “Step 2

Ear-in Wear Detection

  1. This function is provided by fiil + APP

• FIil Tl XS uses capacitance sensor to inducate whether the earbuds is worn or not. Please choose the appropriate size of ear-buds and ear wings to make sure the earbuds is worn correctly.

  1. Please adjust the detection sensitivity from low to high, until it indicates headset is detected as wearing

  2. The incorrect sensitivity setting may result in confusion of wearing detection function or some unnecessary misoperation.

TOUCH SENSITIVITY

This function is provided by fiil + APP\ If you encounter a touch operation error trigger or self-trigger, it means that the current touch sensitivity is too high and needs to be lowered.
If you feel the touch success rate is low, and the effect of adjusting the touch position is not obvious, you need to set the sensitivity to high.

Note: touch sensitivity is set to medium as default

How to Control

  • User Interface Full Control Mode

•Notes: full control mode can be activated in the fiil + APP

How to charge

  • Charge earbud

  • When earbud reminds “recharge headset” or the LED indicator blinks red, that means battery is low and earbud should be charged.

  • Place the earbuds into charging case and close, then earbud will be charged. *Notes: Earbud will power off during charging

  • Charging Case indicator

  • When the LED indicator is on, it means the earbuds are being charged

How to charge

  • Recharge Charging Case
  • When charging case is unable to charge earbud or its LED indicator blinks red, it means battery low and charging case should be recharged.
    e Please connect Type-C cable with USB adapter to recharge charging case.

• Charging Case indicator

  • When both red LED indicators are light on, it means the charging case is being charged.

Product Parameters

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC ID: 2AHGU-F026

IC STATEMENT
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals