EXPLORE WSH5002 CRYSTAL VISION ADVANCED WEATHER STATION TOUCH KEYS Instruction Manual

: June 5, 2024
: EXPLORE

Table of Contents

EXPLORE WSH5002 CRYSTAL VISION ADVANCED WEATHER STATION TOUCH
INSTRUCTION
PRODUCT OVERVIEW
LCD DISPLAY
CLOCK
ALARM
OPERATION
SPECIFICATIONS
DISPOSAL
WARRANTY & SERVICE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

EXPLORE WSH5002 CRYSTAL VISION ADVANCED WEATHER STATION TOUCH

KEYS

INSTRUCTION

These operating instructions are to be considered a component of the device. Please read the safety instructions and the operating instructions carefully before use. Keep these instructions for renewed use at a later date. When the device is sold or given to someone else, the instruction manual must be provided to the new owner/ user of the product. The device is intended only for indoor use.

GENERAL WARNINGS

Risk of electric shock: This device contains electronic components. Only use the device as described in the manual; otherwise, you run the risk of an electric shock.
Choking hazard: Children should only use the device under adult supervision. Keep packaging material, like plastic bags and rubber bands, out of the reach of children, as these materials pose a choking hazard.
Risk of chemical burn: Keep batteries out of the reach of children! Make sure you insert the bateries correctly. Leaking battery acid can lead to chemical burns. Avoid contact of battery acid with skin, eyes and mucous membranes. In the event of contact, rinse the affected region immediately with a plenty of water and seek medical attention.
Risk of fire/explosion : Do not expose the device to high temperatures. Use only the recommended batteries. Do not short-circuit the device or batteries, or throw them into a fire. Excessive heat or improper handling could trigger a short-circuit, a fire, or an explosion.
Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will contact the Service Centre and can send the device in to be repaired, if necessary.
Use only the recommended batteries. Always replace weak or empty batteries with a new, complete set of batteries at full capacity. Do not use batteries from different brands or with different capacities. The batteries should be removed from the unit if it has not been used for a long time.

SCOPE OF DELIVERY

Weather station, Outdoor sensor, Operating instructions, 5V/1A USB adapter, 5x AAA batteries.

BEFORE YOU BEGIN

We recommend using alkaline batteries. If temperatures regularly fall below 0°C (32°F), we recommend using lithium batteries.
Avoid using rechargeable batteries. (Rechargeable batteries cannot maintain correct power requirements.)
Insert batteries before first use, matching the polarity in the battery compartment. 3x AAA Batteries are required for the Weather station and 2x AAA Batteries are required for the Outdoor sensor.

PRODUCT OVERVIEW

Press [ MODE ] to view time and alarm, press and hold to enter time and date setting.
Press [ ALARM ] to turn on/off alarm time, press and hold to enter alarm setting.
In setting mode, press to increase one unit, press and hold to increase rapidly. EU Version: In non-setting mode, press and hold to turn on/off RCC. US Version: In non-setting mode, press and hold to turn on/off atomic clock.
In setting mode, press to decrease one unit, press and hold to decrease rapidly. In other modes, press to turn on/off the Upper and lower temperature and humidity alarm. Hold to enter the Upper and lower temperature and humidity alarm setting.
Press to activate the backlight for 10 seconds or to activate the snooze function to delay the alarm by 5 minutes. When connected to the adapter, the backlight can be set to 4 levels of brightness.
Press [ MAX/MIN ] to view temperature MAX/MIN, press and hold to clear max/min memory.
Press [ CHANNEL ] to view 3 channel outdoor sensor temperature and humidity, press and hold to initialize outdoor sensor channel.
Wall Mount
Battery compartment
Table stand
USB Power In

OUTDOOR SENSOR

Outdoor temperature & humidity LCD display
Battery compartment
TX (Transmit temperature and humidity signal during the sensor initiation search)
Channel switch
C/F switch

BUTTON MODE| MODE| AL ARM| | | M AX/MIN| | CH ANNEL
---|---|---|---|---|---|---|---

Standard mode

and minimum recording of temperature and humidity

|

Adjust backlight brightness with adapter
Turn on backlight for 10 seconds with batteries
SNOOZE 5 minutes when alarm is ringing

mode

Adjust backlight brightness with adapter
Turn on backlight for 10 seconds with batteries

Alarm setting mode

| PRESS| |

Confirm

setting

|

Increase

| Decrease| |

Adjust backlight brightness with adapter
Turn on backlight for 10 seconds with batteries

LCD DISPLAY

Outdoor Temperature & humidity
Weather forecast
Time
Indoor Temperature & humidity
Moon phase
Pressure & Pressure Bar
Date & Week

EU Version: RCC signal received
- US Version: Wave signal received
DST ON (Daylight Saving Time)
Low battery indicator
Temperature and humidity alarm
Ice alert indicator
Alarm
US Time Zone (For US only)

GETTING STARTED

INSERT BATTERIES

Remove the battery door from the back.
Insert 3x AAA (LR03)/1.5V batteries. Please ensure the polarities (+/-) of the batteries match upon installation.
Reattach the battery door.
NOTE: Replace batteries when displays, or when the display is dim.
The weather station is only suitable for mounting at heights ≤ 2 m.

OUTDOOR SENSOR

The main unit can receive data from up to 3 outdoor sensors. 1 Sensor is included with delivery.

Remove the battery door from the back.
Insert 2x AAA (LR03)/1.5V batteries. Please ensure the polarities (+/-) of the batteries match upon installation.
Select a channel, then press TX.
Reattach the battery door.
Place the sensor within 30 m (98 ft) of the main unit

TO SEARCH FOR A SENSOR:

The main unit will automatically search for a new sensor after the batteries are installed. To manually initiate a outdoor sensor search, press and hold [ CHANNEL ].
NOTE: The transmission range may vary depending on many factors. You may need to experiment with various locations to get the best results.

CLOCK

match upon

CLOCK RECEPTION

When you insert or replace the batteries, RCC (atomic) reception is initiated. To manually start RCC (atomic) reception press and hold the button.
The receiving process duration is 7 minutes.
During receiving process, the RCC (atomic) signal symbol shows: .
If the RCC (atomic) receiving process is successful, a completed RCC (atomic) symbol will be shown in the display and the date and time will be set automatically. If it fails within 7 minutes, RCC (atomic) setting will quit automatically. If that happens, press and hold the button to reinitiate RCC (atomic) receiving.

NOTE : The interference from the power adapter will affect RCC (atomic) reception. It is recommended to place the power adapter at least 1m away from the console to get the best RCC (atomic) reception.

SET THE CLOCK MANUALLY

Press and hold [ MODE ] button to enter into time and date setting.
The setting parameter will flash.
Press button once, the figure will increase 1 unit. Press and hold the button, the figures will increase rapidly.
Press button once, the figure will decrease 1 unit. Press and hold the button, the figures will decrease rapidly.
Press [ MODE ] button to confirm setting and enter to next parameter.
Sequence of setting:
EU/AUS Version : 12/24h format Hour Minute Year Month Day Language Time zone Key tone on / off Temperature unit (°C/°F) Pressure unit Exit
US Version : 12/24h format Hour Minute Year Month Day Language Time zone DST ON/OFF Key tone on / off Temperature unit (°C/°F) Pressure unit Exit
If there is no action in 20 seconds, the setting will be saved and you will exit the setting mode.

ALARM

SETTING/ADJUSTING ALARM TIME

Press and hold [ ALARM ] to enter alarm setting mode.
The setting parameter will flash.
Press or button to set the desired data.
Press [ ALARM ] button to confirm setting and exit.
The alarm will sound when the alarm setting is finished and turned on.

TURN ON/OFF ALARM

Press the [ ALARM ] button to turn on/off the alarm.

OPERATION

At the set alarm time, alarm signal rings.
During the alarm, press the button to delay the alarm by 5 minutes.
If you do not press any button to stop the alarm, it will automatically turn off after 2 minutes.
To stop the alarm, press [ ALARM ] or any other button, except for SNOOZE.
The alarm will start again at the next alarm time, unless you switch off the alarm function by pressing the [ ALARM ] button until the alarm is set to off.

WEATHER FORECAST

This device forecasts the next 12-24 hours of weather within a 30-50 km (19-31 mile) radius with a 75% accuracy.

SYMBOL	DESCRIPTION
Sunny
Sunny to cloudy
Cloudy
Cloudy to rain
Cloudy to snow

PRESSURE

The trend of the air pressure within the last 24 hours is displayed in the form of a bar diagram. The scale goes from 1 (1 hour ago) to 24 (24 hours ago).

Press and hold [ MODE ], then press [ MODE ] to enter pressure unit setting, to select mmHg/inHg/ hPa.

MOON PHASE

The phase of the moon depends on the current date. It is automatically calculated and the following symbols are displayed:

SYMBOL	DESCRIPTION
Full moon
Waning moon
New moon
Waxing moon
Full moon

LANGUAGE

1. Press and hold [ MODE ] button to enter time setting, press [ MODE ] to enter language setting.

Sequence of setting weekday language:
EU/AUS Version : German (GER) English (ENG) Italian (ITA) French (FRE) Netherlands (NET) Spain (ESP) Danish (DAN)
US Version: English (ENG) Italian (ITA) French (FRE) Netherlands (NET) Spain (ESP) Danish (DAN) German (GER)
Symbo l GER| ENG| I TA| FRE| N E T| ESP| D A N
---|---|---|---|---|---|---
Mond a y MON| MON| LUN| LUN| MAA| LUN| MAN
T uesd a y DIE| TUE| MAR| MAR| DIN| MAR| TIR
W e dne sd a y ** MIT| WED| MER| MER| WOE| MIE| ONS
Thursd a y DON| THU| GIO| JEU| DON| JUE| TOR
F rid a y FRE| FRI| VEN| VEN| VRI| VIE| FRE
Satu r d a y SAM| SAT| SAB| SAM| ZAT| SAB| LOR
Sund a y** SON| SUN| DOM| DIM| ZON| DOM| SON

TEMPERATURE AND HUMIDITY

The indoor temperature is always displayed in the left bottom corner of the screen. To receive outdoor temperature, you can connect up to 3 outdoor sensors to the main unit. Press the [ CHANNEL ] button to toggle between Channel 1-3.
MAX/MIN MEMORY

To toggle between current, minimum and maximum records for the selected sensor, press [ MAX/MIN ] repeatedly. To clear records, press and hold [ MAX/MIN ] in max/min interface.

NOTE : When the indoor temperature is lower than -5 °C (23.0 °F), the screen displays LL.L. When the temperature is higher than 50 °C (122.0 °F), the screen displays HH.H.

TEMPERATURE AND HUMIDITY ALARM SETTING

Press and Hold enter to set temperature and Humidity alarm.
The setting parameter will flash.
Press or button to set the desired data.
Press [ MODE ] button to confirm setting and enter to next parameter.
Sequence of setting: Indoor upper temperature limit  Indoor lower temperature limit  Indoor upper humidity limit  Indoor lower humidity limit  outdoor upper temperature limit  outdoor lower temperature limit  outdoor upper humidity limit  outdoor lower humidity limit

TEMPERATURE AND HUMIDITY ALARM OPERATION

Press to on/off temperature and Humidity alarm.
When the measured temperature or humidity is greater than the set upper limit or lower than the set lower limit, the station will give an alarm.

ICE ALERT

If the channel 1 sensor falls between -2°C to 3°C (28°F to 37°F), the ice alert indicator will display, and will disappear once the temperature is out of this range.

BACKLIGHT

Press [ ] to activate backlight for 10 seconds.
When connected to the adapter, the backlight can be set to 4 levels of brightness.
NOTE : The backlight would be weakened during the RCC (wave) signal reception.

SPECIFICATIONS

MAIN UNIT:

Dimensions : 176 x 25 x 131 mm (L x W x H)
Weight : 290 g (Exclude batteries)
Power: 3x AAA (LR03) 1.5V batteries , 5V/1A USB Adapter

TEMPERATURE:

Indoor temperature display range: 5°C to +50°C (23°F to 122°F)
Outdoor temperature display range: -20°C to +60°C (-4°F to 140°F)

HUMIDITY:

Indoor/outdoor humidity range: 20% – 95% RH

OUTDOOR SENSOR:

Dimensions: 60 x 20 x 60 mm (L x W x H)
Weight: 45 g (Exclude batteries)
Transmission range: 30 m (98 ft)
Temperature range: -20°C to 60°C (-4°F to 140°F)
Signal frequency : 433 MHz
Maximum transmission power: under 10mW
Power: 2x AAA (LR03) 1.5V batteries

EC DECLARATION OF CONFORMITY

Hereby, Bresser GmbH (Folux GmbH) declares that the equipment type with part number: WSX5002 is in compliance with Directive: 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:

www.bresser.de/ download/WSX5002/CE/WSX5002_CE.pdf

RCM DECLARATION OF CONFORMITY

The adapter complies with electrical safety, EMC and radio spectrum regulatory requirements for products supplied to the Australia or New Zealand market.

FCC COMPLIANCE STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be detemined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Suppliers Name : Guangzhou Bresser Optical Instrument Co., Ltd.
Suppliers Address : Kangda Rd. 12, Yunpu Ind. Area, Huangpu, Guangzhou, PRC
Suppliers phone number : 866.252.3811

NOTES ON CLEANING

Remove the batteries before cleaning.
Only use a dry cloth to clean the exterior of the device. To avoid damaging the electronics, do not use any cleaning fluid.
Protect the device from dust and moisture.

DISPOSAL

Dispose of the packaging materials properly, according to their type, such as paper or cardboard. Contact your local waste disposal service
or environmental authority for information on the proper disposal.

Do not dispose of electronic devices in the household garbage!As per the Directive 2002/96/EC of the European Parliament on waste electrical and electronic equipment and its adaptation into German law, used electronic devices must be collected separately and recycled in an environmentally friendly manner.

In accordance with the regulations concerning batteries and rechargeable batteries, disposing of them in the normal household waste is explicitly forbidden. Please make sure to dispose of your used batteries as required by law — at a local collection point or in the retail market. Disposal in domestic waste violates the Battery Directive. Batteries that contain toxins are marked with a sign and a chemical symbol.

battery contains cadmium
battery contains mercury
battery contains lead

WARRANTY & SERVICE

EU Version The regular guarantee period is 5 years and begins on the day of purchase.
You can consult the full guarantee terms as well as information on extending the guarantee period and details of our services at www.bresser.de/warranty_terms.
Would you like detailed instructions for this product in a particular language? Then visit our website via the link below (QR code) for available versions.
Alternatively you can also send an email to manuals@bresser.de or leave a message on +49 (0) 28 72 – 80 74-220*. Please always state your name, precise address, a valid phone number and email address, as well as the article number and name.
Number charged at local rates in Germany (the amount you will be charged per phone call will depend on the tariff of your phone provider); calls from abroad will involve higher costs.

MANUAL DOWNLOAD: