Einhell TE-CS Cordless Handheld Circular Saw Instructions
- June 5, 2024
- Einhell
Table of Contents
TE-CS Cordless Handheld Circular Saw
Instructions
![Einhell TE-CS Cordless Handheld Circular Saw
- fig 3](https://manuals.plus/wp-content/uploads/2022/06/Einhell-TE-CS- Cordless-Handheld-Circular-Saw-fig-3.png)
Danger! – Read the operating instructions to reduce the risk of inquiry
Caution! Wear ear-muff s. The impact of noise can cause damage to hearing.
Caution! Wear a breathing mask. Dust that is injurious to health can be generated when working on wood and other materials. Never use the device to work on any materials containing asbestos!
Caution! Wear safety goggles. Sparks generated during working or splinters, chips, and dust emitted by the device can cause loss of sight.
Pull out the plug or battery pack!
Danger!
When using the equipment, a few safety precautions must be observed to avoid
injuries and damage. Please read the complete operating instructions and
safety regulations with due care. Keep this manual in a safe place, so that
the information is available at all times. If you give the equipment to any
other person, hand over these operating instructions and safety regulations as
well. We cannot accept any liability for damage or accidents which arise due
to a failure to follow these instructions and the safety instructions.
Safety regulations
The corresponding safety information can be found in the enclosed booklet.
Warning!
Read all the safety information, instructions, illustrations, and technical
data provided on or with this power tool. Failure to adhere to the following
instructions may result in electric shock, fi re, and/or serious injury.
Keep all the safety information and instructions in a safe place for future
use.
Layout and items supplied
2.1 Layout (Fig. 1a/1b)
- Handle
- ON/OFF switch
- Locking button for ON/OFF switch
- Locking lever for cutting depth setting
- LED lamp
- Soleplate
- Locking lever for miter setting
- Locking screw for parallel stop
- Scale for miter angle
- Additional handle
- Spindle lock
- Saw blade
- Saw blade wrench
- Connection for sawdust extractor
- Line guide
- Parallel stop
- Screw for securing the saw blade
- Flange
- Swing guard hood
- Lever for swing guard hood
2.2 Items supplied
Please check that the article is complete as specifi ed in the scope of
delivery. If parts are missing, please contact our service center or the sales
outlet where you made your purchase at the latest within 5 working days after
purchasing the product and upon presentation of a valid bill of purchase.
Also, refer to the warranty table in the service information at the end of the
operating instructions.
- Open the packaging and take out the equipment with care.
- Remove the packaging material and any packaging and/or transportation braces (if available).
- Check to see if all items are supplied.
- Inspect the equipment and accessories for transport damage.
- If possible, please keep the packaging until the end of the guarantee period.
Danger!
The equipment and packaging material are not toys. Do not let children play
with plastic bags, foils, or small parts. There is a danger of swallowing or
suff locating!
- Cordless Handheld Circular Saw
- Saw blade
- Saw blade wrench
- Parallel stop
- Original operating instructions
- Safety instructions
Proper use
The cordless handheld circular saw is designed for sawing straight cuts in
wood, wood-type materials, and plastics. In the case of plastic workpieces, be
careful not to overheat the tips of the saw blade and melt the plastic.
The equipment is to be used only for its prescribed purpose. Any other use is
deemed to be a case of misuse. The user/operator and not the manufacturer will
be liable for any damage or injuries of any kind caused as a result of this.
Please note that our equipment has not been designed for use in commercial,
trade, or industrial applications. Our warranty will be voided if the machine
is used in commercial, trade, or industrial businesses or for equivalent
purposes.
Technical data
Motor power supply: …………………………. 18 V DC
Idling speed: ………………………………….4200 min-1
Cutting depth at 90°: ………………………….. 48 mm
Cutting depth at 45°: ………………………….. 32 mm
Saw blade: ……………………………………Ø 150 mm
Blade holder: ………………………………Ø 10/16 mm
Blade thickness: ……………………………….. 1.6 mm
Weight: ……………………………………………….2.8 kg
Danger!
Sound and vibration
Sound and vibration values were measured in accordance with EN 62841.
LPA sound pressure level …………….. 105.17 dB(A)
KPA uncertainty ……………………………………… 3 dB
LWA sound power level ………………. 116.17 dB(A)
KWA uncertainty ……………………………………… 3 dB
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions) determined in
accordance with EN 62841.
Handle
Vibration emission value ah, W = 1.482 m/s²
K uncertainty = 1.5 m/s²
Additional handle
Vibration emission value ahW= 1.335 m/s²
K uncertainty = 1.5 m/s²
The stated vibration emission levels and stated noise emission values were
measured in accordance with a set of standardized criteria and can be used to
compare one power tool with another.
The stated vibration emission levels and stated noise emission values can also
be used to make an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary from the level specifi ed
during actual use, depending on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a minimum.
- Only use appliances that are in perfect working order.
- Service and clean the appliance regularly.
- Adapt your working style to suit the appliance.
- Do not overload the appliance.
- Has the appliance been serviced whenever necessary?
- Switch the appliance off when it is not in use.
- Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in In accordance with
instructions, certain residual risks cannot be ruled out. The following
hazards may arise in connection with the equipment’s construction and
layout:
- Lung damage if no suitable protective dust the mask is used.
- Damage to hearing if no suitable ear protection is used.
- Health damage is caused by hand-arm vibrations if the equipment is used over a prolonged period or is not properly guided and maintained.
Before starting the equipment
Warning!
Always remove the battery pack before making adjustments to the equipment.
5.1 Setting the cutting depth (Figure 2/3)
- Release the handle on the rear of the guard hood for adjusting the cutting depth (4).
- Place the saw foot (6) flat on the surface of the workpiece you wish to see. Raise the saw until the saw blade (12) is at the required cutting depth (a).
- Refasten the handle for adjusting the cutting depth (4). Check the handle is securely fastened.
5.2 Miter stop (Figure 4/5)
- The preset standard angle between the saw foot (6) and saw blade (12) is 90°. You can adjust this angle to carry out angled cuts.
- Release the locking lever for miter setting (7) on the front of the saw foot.
- You can now adjust the cutting angle to around 45°. Keep an eye on the cutting angle scale (9) as you do so.
- Refasten the locking lever for the miter setting (7).
Check the handle is securely fastened.
5.3 Extraction of dust and chips (Figure 6)
- Connect a suitable vacuum cleaner to the provided chip extractor connector (14) of your circular saw (vacuum cleaner not included). This will provide excellent dust extraction on the workpiece. The benefits are that you will protect both the equipment and your own health. Your work area will also be cleaner and safer.
- Dust created when working may be dangerous. Refer to the section entitled “Safety instructions”.
- Important! The vacuum cleaner you use for the extraction work must be suitable for the workpiece material.
- Check that all the parts are properly connected.
5.4 Parallel stop (Figure 7/8)
- The parallel stop (16) enables you to sew parallel lines.
- Loosen the locking screw for the parallel stop (8) on the saw foot (6).
- To assemble, slide the parallel stop (16) into the guide (c) on the saw foot (6) (see Figure 7)
- Set the required spacing and then tighten the locking screw (8) again.
- Using the parallel stop: Position the parallel stop (16) flat on the edge of the workpiece and start the cut.
Important! Carry out a trial cut in a piece of waste wood
5.5 Line guide (Fig. 9)
Using the line guide (15) you can carry out exact cuts following cutting lines
marked on the workpiece.
Use mark (d) for the 0° or 90°angle setting and mark (b) for the 45° angle
setting. For information on the angle, set see 5.2
Important! Carry out a trial cut in a piece of waste wood
5.6 Charging the LI battery pack (Fig. 10-11)
- Remove the battery pack (g) from the handle, pressing the push-lock buttons (f) downwards to do so.
- Check that your mains voltage is the same as that marked on the rating plate of the battery charger. Insert the power plug of the charger (j) into the main socket outlet. The green LED will then begin to fl ash.
- Push the battery pack onto the battery charger.
In section 10 “Charger indicator” you will find a table with an explanation of
the LED indicator on the charger.
If the battery pack fails to become charged, please check
- whether there is the voltage at the socket outlet
- and whether there is proper contact at the charging contacts on the charger.
If the battery still fails to become charged, please return
- the charger
- and the battery pack
to our Customer Service Department.
To ensure that items are properly packaged and delivered when you send them
to us, please contact our customer service or the point of sale at which the
equipment was purchased.
When shipping or disposing of batteries and cordless tools, always ensure
that they are packed individually in plastic bags to prevent short circuits
and fires.
To ensure that the battery pack provides a long service, you should take
care to recharge it promptly. You must recharge the battery pack when you
notice that the performance of the device drops. Never allow the battery pack
to become fully discharged. This will cause it to develop a defect.
5.7 Battery capacity indicator (Fig. 10 – Item h)
Press the battery capacity indicator switch (i). The battery capacity
indicator (h) shows the charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
If the battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the battery from the equipment, and
keep it at room temperature for one day. If the fault reoccurs, this means
that the rechargeable battery has undergone exhaustive discharge and is
defective. Remove the battery from the equipment. Never use or charge a
defective battery.
Operation
Warning!
Always remove the battery pack before making adjustments to the equipment.
6.1 Working with the hand-held circular saw
- Always hold the circular saw firmly.
- The swing guard hood (19) is pushed back automatically by the workpiece.
- Do not use force!
- Push forwards gently and evenly with the circular saw.
- The waste piece should be on the right-hand side of the circular saw so that the wide section of the support bench supports its full area.
- If you are sawing down a line that has been drawn, guide the circular saw along with the corresponding notch.
- Clamp small pieces of wood securely before sawing them. Never hold them with your hand.
- Always follow the safety instructions. Wear safety goggles.
- Do not use defective saw blades or blades that are cracked or broken.
- Do not use any flanges/flange nuts whose borehole is larger or smaller than those in the saw blade.
- The saw blade must not be decelerated by hand or by applying lateral pressure to the blade.
- The swing guard hood must not jam and must return to its initial position after the operation has been completed.
- Before you use the circular saw, check the function of the swing guard hood with the main plug disconnected.
- Before you use the machine, ensure that the safety equipment such as the swing guard hood, flanges, and adjustment devices are in working order and are correctly adjusted and secure.
- You can connect a suitable dust extraction system to the sawdust extraction connector (14). Ensure that the dust extractor line is safely and correctly connected.
- The moving swing guard hood must not be fixed in the retracted guard hood when the saw is in use.
6.2 Using the circular saw
- Adjust the cutting depth, cutting angle, and parallel stop (see sections 5.1, 5.2, and 5.4)
- Do not switch on the circular saw until you have fitted a saw blade.
- Place the saw foot flat on the workpiece you wish to see. The saw blade must not be in contact with the workpiece.
- Hold the circular saw firmly with both hands.
6.3 Switching ON/OFF (Fig. 12)
To switch on:
Press the locking button (3) and the ON/OFF switch (2) at the same time
- Allow the saw blade to accelerate until it reaches full speed. Then slowly move the saw blade along the cutting line. Only exert gentle pressure on the saw blade as you do so.
To switch off:
Release the locking button and ON/OFF switch
- If you release the handle the equipment will shut down automatically which means that it cannot operate accidentally.
- Ensure that you do not cover or block the ventilation openings whilst working with the tool.
- Do not slow down the saw blade after you switch it off by pressing it sideways.
- Important! Do not put down the machine until the saw blade has reached a complete standstill.
Important. Carry out a trial cut in a piece of waste wood
6.4 Changing the saw blade (Fig. 13-16)
Warning!
Always remove the battery pack before making adjustments to the equipment.
Use only saw blades that comply with standard EN 847-1 and are of the same
type as the saw blade supplied with this circular saw. Ask your dealer for
advice.
Use the saw blade key (13) supplied to change the saw blade. The saw blade key
(13) is stored in the housing. If required, pull the saw blade key (13) out of
the housing (see Figure 13).
Important. The hand-held circular saw must not be operated with the saw
blade key (13) inserted in it.
- Press the spindle lock (11).
- Undo the screw to secure the saw blade (17) using the saw blade key (13).
- Push back and secure the moving swing guard hood (19) using the lever for the swing guard hood (20).
- Remove the flange (18) and the saw blade (12) in a downwards direction.
- Clean the flange and insert the new saw blade. Pay attention to the running direction (see arrow on the guard hood and saw blade).
For 10 mm blade holder:
- Place the flange (18) on the blade with the flat side against the blade. (Make sure that the flange is correctly positioned)
For the 16 mm blade holder:
- Place the flange (18) on the blade with the raised side against the blade. (Make sure that the flange is correctly positioned)
Warning! With the 16 mm holder, the flange must center the blade. Therefore, pay special attention to making sure that the raised part of the flange is correctly positioned in the blade.
- Tighten the screw to secure the saw blade (17), and check it runs true.
- Before you press the On/Off switch, make sure that the saw blade is correctly fitted and that moving parts run smoothly, and that the clamping screws are tightened securely.
6.5 LED lamp (Fig. 1/Item 5)
The LED lamp (5) can be used in poor lighting conditions to additionally
illuminate the cutting position. The LED lamp (5) will come on automatically
as soon as you press the locking button for the On/Off switch (3).
Cleaning, maintenance, and ordering of spare parts
Danger!
Always pull out the battery pack before starting any cleaning work.
7.1 Cleaning
- Keep all safety devices, air vents, and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure.
- We recommend that you clean the device immediately each time you have finished using it.
- Clean the equipment regularly with a moist cloth and some soft soap. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. Ensure that no water can seep into the device. The ingress of water into an electric tool increases the risk of an electric shock.
7.2 Maintenance
There are no parts inside the equipment which require additional maintenance.
7.3 Ordering replacement parts:
Please quote the following data when ordering replacement parts:
- Type of machine
- Article number of the machine
- Identification number of the machine
- Replacement part number of the part required
For our latest prices and information please go to www.Einhell- Service.com
Disposal and recycling
The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal. If you do not know the whereabouts of such a collection point, you should ask in your local council offices.
Storage
Store the equipment and accessories in a dark and dry place at above freezing temperature. The ideal storage temperature is between 5 and 30 °C. Store the electric tool in its original packaging.
For EU countries only
Never place any electric power tools in your household refuse.
To comply with European Directive 2012/19/EC concerning old electric and
electronic equipment and its implementation in national laws, old electric
power tools have to be separated from other waste and disposed of in an
environment-friendly fashion, e.g. by taking to a recycling depot.
Recycling alternative to the return request: As an alternative to returning
the equipment to the manufacturer, the owner of the electrical equipment must
make sure that the equipment is properly disposed of if he no longer wants to
keep the equipment. The old equipment can be returned to a suitable collection
point that will dispose of the equipment in accordance with the national
recycling and waste disposal regulations. This does not apply to any
accessories or aids without electrical components supplied with the old
equipment.
The reprinting or reproduction by any other means, in whole or in part, of
documentation and papers accompanying products, is permitted only with the
express consent of the Einhell Germany AG.
Subject to technical changes
Charger indicator
Indicator status | Explanations and actions |
---|---|
Red LED | Green LED |
Off | Flashing |
is ready for use; there is no battery pack in the charger
On| Off| Charging: The charger is charging the battery pack in quick
charge mode. The charging times are shown directly on the charger.
Important! The actual charging times may vary slightly from the stated
charging times depending on the existing battery charge.
Off| On| The battery is charged and ready for use.
The unit then changes over to gentle charging mode until the battery is fully
charged.
To do this, leave the rechargeable battery on the charger for approx. 15
minutes longer.
Action: Take the battery pack out of the charger. Disconnect the charger
from the main supply.
Flashing| Off| Adapted charging: The charger is in gentle charging mode.
For safety reasons the charging is performed less quickly and takes more time.
The reasons can be:
– The rechargeable battery has not been used for a very long time. – The
battery temperature is outside the ideal range.
Action: Wait for the charging to be completed; you can still continue to
charge the battery pack.
Flashing| Flashing| Fault: Charging is no longer possible. The battery
pack is defective.
Action: Never charge a defective battery pack. Take the battery pack out
of the charger.
On| On| Temperature fault: The battery pack is too hot (e.g. due to
direct sunshine) or too cold (below 0° C).
Action: Remove the battery pack and keep it at room temperature (approx.
20° C) for one day.
Service information
We have competent service partners in all countries named on the guarantee
certifi cate whose contact details can also be found on the guarantee
certificate. These partners will help you with all service requests such as
repairs, spare and wearing part orders, or the purchase of consumables.
Please note that the following parts of this product are subject to normal or
natural wear and that the following parts are therefore also required for use
as consumables.
Category | Example |
---|---|
Wear parts* | Battery |
Consumables* | Saw blade |
Missing parts |
-
Not necessarily included in the scope of delivery!
In the effect of defects or faults, please register the problem on the internet at www.Einhell-Service.com.
Please ensure that you provide a precise description of the problem and answer the following questions in all cases:- Did the equipment work at all or was it defective from the beginning?
- Did you notice anything (symptom or defect) prior to the failure?
- What malfunction does the equipment have in your opinion (main symptom)?
Describe this malfunction.
Warranty certificate
Dear Customer,
All of our products undergo strict quality checks to ensure that they reach
you in perfect condition. In the unlikely event that your device develops a
fault, please contact our service department at the address shown on this
guarantee card. You can also contact us by telephone using the service number
shown. Please note the following terms under which guarantee claims can be
made:
-
These guarantee terms apply to consumers only, i.e. natural persons intending to use this product neither for their commercial activities nor for any other self-employed activities. These warranty terms regulate additional warranty services, which the manufacturer mentioned below promises to buyers of its new products in addition to their statutory rights of guarantee. Your statutory guarantee claims are not affected by this guarantee. Our guarantee is free of charge to you.
-
The warranty services cover only defects due to material or manufacturing faults on a product which you have bought from the manufacturer mentioned below and are limited to either the rectifi cation of said defects on the product or the replacement of the product, whichever we prefer. Please note that our devices are not designed for use in commercial, trade, or professional applications. A guarantee contract will not be created if the device has been used by commercial, trade, or industrial business or has been exposed to similar stresses during the guarantee period.
-
The following are not covered by our guarantee:
– Damage to the device caused by a failure to follow the assembly instructions or due to incorrect installation, a failure to follow the operating instructions (for example connecting it to an incorrect mains voltage or current type), or a failure to follow the maintenance and safety instructions or by exposing the device to abnormal environmental conditions or by lack of care and maintenance.
– Damage to the device caused by abuse or incorrect use (for example overloading the device or the use of unapproved tools or accessories), ingress of foreign bodies into the device (such as sand, stones or dust, transport damage), the use of force or damage caused by external forces (for example by dropping it).
– Damage to the device or parts of the device caused by normal or natural wear or tear or by normal use of the device. -
The guarantee is valid for a period of 24 months starting from the purchase date of the device. Guarantee claims should be submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or parts fi tted. This also applies if on-site service is used.
-
To make a claim under the guarantee, please register the defective device at: www.Einhell-Service.com. Please keep your bill of purchase or other proof of purchase for the new device. Devices that are returned without proof of purchase or without a rating plate shall not be covered by the guarantee, because appropriate identification will not be possible. If the defect is covered by our guarantee, then the item in question will either be repaired immediately and returned to you or we will send you a new replacement.
Of course, we are also happy to offer a chargeable repair service for any
defects which are not covered by the scope of this guarantee or for units that
are no longer covered. To take advantage of this service, please send the
device to our service address.
Also refer to the restrictions of this warranty concerning worn parts,
consumables, and missing parts as set out in the service information in these
operating instructions.
Declaration of conformity: We declare conformity in accordance with the EU directive and standards for article
*Akku-Handkreissäge TE-CS 18/150 Li (Einhell)**
2014/29/EU
2005/32/EC_2009/125/EC
(EU)2015/1188
2014/35/EU
2006/28/EC
2014/30/EU
2014/32/EU
2014/53/EU
2014/68/EU
(EU)2016/426
Notifi ed Body:
(EU)2016/425
2011/65/EU_(EU)2015/863| 2006/42/EC
Annex IV
Notifi ed Body:
Reg. No.:
2000/14/EC_2005/88/EC
Annex V
Annex VI
Noise: measured LWA = dB (A); guaranteed LWA = dB (A)
P = kW; L/Ø = cm
Notifi ed Body:
2012/46/EU_(EU)2016/1628
Emission No.:
Standard references: EN 62841-1; EN 62841-2-5; EN 55014-1; EN 55014-2
ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar
Date: 03.09.2021
First CE: 2019
Art.-No.: 43.312.20
I.-No.: 21021
Subject to change without notice| Archive-File/Record: NAPR025973
Documents registrar: Alex Kurz
Wiesenweg 22, D-94405 Landau/Isar
Cordless Handheld Circular Saw
Declaration of conformity
We, Einhell UK Ltd
Champions Business Park, First Floor Unit 10, Arrowe Brook Rd, Upton, Wirral
CH49 0AB, United Kingdom
declare the conformity to UK standards and legislation was assessed for:
Cordless Circular Saw TE-CS 18/150 Li (Einhell)
UK legislation
Simple Pressure Vessels (Safety) Regulation
Electrical Equipment (Safety) Regulation
Radio Equipment Regulation
Personal Protective Equipment Regulation
Electromagnetic Compatibility Regulation
Measuring Instruments Regulation
Pressure Equipment (Safety) Regulation
The Ecodesign for Energy-Related Products and Energy Information Regulation
The Restriction of the Use of Certain Hazardous Substances in Electrical and
Electronic Equipment Regulation
Noise Emission in the Environment by Equipment for use Outdoors Regulation
Noise: measured LWA = dB (A); guaranteed LWA = dB (A)
Supply of Machinery (Safety) Regulation
Annex IV
UK Approved Body:
UKTE Certifi cate No.:
Standards: BS 62841-1; BS 62841-2-5; BS 55014-1; BS 55014-2
Wirral, 2021.09.03
Article Number: 43.312.20
I.-No.: 21021
Subject to change without notice| Archive-File/Record: NAPR025973
Documents registrar: Alex Kurz
Wiesenweg 22, 94405 Landau/Isar, Germany
EH 09/2021 (01)
14.09.2021 14:59:41
Documents / Resources
|
Einhell TE-CS Cordless Handheld Circular
Saw
[pdf] Instructions
TE-CS Cordless Handheld Circular Saw, Cordless Handheld Circular Saw, Circular
Saw, 18 150 Li
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>