FOS Lighting Color Video Conference Camera User Manual

FOS Lighting Color Video Conference Camera

Thank you very much for using our color video conference camera. Please read this manual in detail and use it accordingly. This manual introduces the function of a video camera, opening, and operation principles in detail. This color video camera is high-quality and flexible with a remote pan355° /tilt 120° operation and image flip, and DSP dealing integration module input. Support VISCA and PELCO P/D protocol. Allowing installation on the ceiling /desk and accurate remote control of RS232/485.

Instruction

In order to avoid the camera and other connecting equipment being damaged and leading to potential danger,

• please follow the rules below:
• Only professional technician can install and maintain; Prohibit setting on the places which raining or dampness, using unit under stated temperature, humidity, and power;
• Using accessories from the original factory or allowed;
• Once an exchange of product or repair happen please use a universal meter test before using;
• Please use a soft and dry rag for cleaning, no strongly corrosive cleanser for avoiding mangled for outside of the camera or lens;
• Take care using and no squeeze crust avoiding camera broken;
• The bracket must endure 3 times the weight of the camera at least.

1. 1080p full HD PTZ camera
2. Pan 355°, Tilt 120°
3. The latest developed digital signal processor (DSP) improves the image quality of digital zoom
4. Multi-function IR remote controller can control PTZ, Lens and other functions conveniently.
5. Using PC to control the camera with Sony VISCA or Pelco command
6. IR remote controller, RS422C, RS232C, and other control methods preset positions by remote controller, 200preset positions by PC or remote control unit, memory auto-saved when power off
7. The maximum speed of horizontal rotation:80° /s, Tilt:60° /s
8. Providing multifunctional accurate remote control

Packing List

Please check up all devices inside while opening the package.

• Video camera—————-1
• Power adapter—————1
• Power cable—————1
• Rs232 cable—————1
• Remote controller—————1
• HDMI wire—————1
• USB W’ire————-1
• Ceiling bracket ———-1

Front

1. Lens
   Sensor for the Remote Control

2. Power lamp

3. Standby lamp

4. RS-422C/485 VISCA/PELCO

5. IR select switch

6. VISCA RS-232C IN connector

7. VISCA RS-232C OUT connector

8. 3G-SDI HD video output

9. RJ-45 Network video output

10. Line-in

11. HDMI video output

12. DVI- I video output (transfer HDMI)

13. DC IN 12V input 14 USB video output

14. British screw holes

15. VISCA RS-422/RS-232C BOTTOM switch (See page 9 for details) 

Bottom

Remote Controller

• CAMERA SELECT: (match to IR SELECT back)
• FOCUS: (auto or manual)
• MANU
• BACKLIGHT
• POWER
• STD, REV: (Press L/RDIRECTION SET, and then Press 1 or 2)
• POSITION: (Number area; PRESET: press PRESET then press 1-9 for set up preset position)
• RESET: (Press RESET and then press 9 for eliminate the preset position)
• ZOOM: (Telephoto or Wide A ng l e )
• PAN-TILT RESET 411 PAN-TILT; HOME for return middle position @ L/R DIRECTION SET  IR transmit
• 41. CLOSE THE MENU
• S-OUT: SWITCH TO 72OP5O
• DATA-SCREEN: Switching color mode
• Brightness adjustment: br i gh t – / bright+

Install diagram

VI SCA RS – 422

Pin 0.

• 0 . Function
• TXD rN+
• 2 TXD IN-
• 3 RX D J N+(RS 485 – )
• 4 RX D IN- RS4 85+)
• 5 GN D
• 6 TXD OUT+
• 7 TXD OUT-
• 8 RXD OUT+
• 9 RXD OUT-

video camera Windows D-Sub 9 pin

EVI Camara or Mini DIM 8 pin serial

Windows D-Sub 25 pin

Pan/Ti 1t control

1. Power on, Pan/Tilt will be in the initial position.
2. Press the arrow to adjust direction, when you can watch a video on screen, you can move direction by pressing the arrow step by step or continuously for wild turning direction. If you want to fix the direction, please press the arrow (up or down) and arrow (left or right) at the same time.
3. Press HOME for the front direction.
4. Press PAN-TILT RESET or turn off the power and then turn on if direction is not you want, the direction will be change to initial position.
5. Press L/R DIRECTION SET and STD or REV at the same time, meanwhile, move right arrow, you can turn the direction to left or right.

ATTENTION:
When you use more than one commander, please repeat the operation accordingly.

Adjust Camera

FOCUS

• Press AUTO for focus auto
• Press MANUAL and then adjust far or nearby switching FAR OR NEAR

ATTENTION:
In the condition of far focus, it is natural for the image to twitter slow when operating pan/tilt.

ZOOM
Adjust T and W for zoom far or near

One Remote controller for operating a few cameras

1. Maximum 3 cameras can be controlled by a remote controller through back switches 1, 2, and 3.
2. Press CAMERA SELECT 1 or 2 or 3, you can control each of the matching 1, 2, 3 cameras, 1 or 2 or 3 buttons will be lighted.

Use backlight compensation
If there is lighting on the back of the focusing object, the object will be looks black. So you can press BACK LIGHT for avoiding this happening, and turn off button for close.

Preset Position Operation
Store camera settings-presets Up to 200 presets can be set (location, zoom, focus, and the background light) By remote controller only can set and calling 9 preset positions. Through a user-defined protocol Over 200 presets that can be set.

1. Recognizes that the STANDBY led is not blinking. If the STANDBY indicator is flashing, press PAN-TILT RESET to restored
2. Adjust the camera position, zoom, focus, and background light.
3. Press and hold the PRESET button, then press one of the position-9.

Use preset position
Press any switch of 1-9 position

Cancel preset position
Press RESET, then press 1-9 simultaneously

Attention

Normal set or ceiling set RS232 RS422/485 selection the remainder being reserved switch.

BOTTOM SWITCH

Note:
The third bottom switch is for an upgrade, do not keep it on while using it .

Communication
This option can set protocol, address, baud rate, speed scale, and speed limit when the camera is communicating through the serial port.

PTZ settings
This option can set PTZ-related functions, including digital zoom, focus mode, remote speed, pan direction, tilt direction, flip, and mirror.

Exposure settings
This option can set exposure mode including full auto exposure, manual exposure, shutter priority, iris priority, bright priority, etc.

White balance settings
This option can set white balance mode including auto, manual, indoor, outdoor, one push, ATW, etc.

Picture Settings
This option allows you to set image effects, including 2D/3D noise reduction, contrast, chroma, acutance, gamma, wide dynamic range, defog, anti-flicker, etc.

Network information
This option can set network information of the camera, including DHCP on/off. When the DHCP is off, we can edit the camera IP address, mask, and gateway by using “0-9” of the IR remote controller.

System setting
This option can set camera resolution, reload preset l, RS485 search function, language, check the current version, and back to factory setting.

Setting

Communication

Communication Sub menu

• Protocol: can set auto/visca/pelco-p/pelco-d
• Address: can set camera serial communication address
• Baud rate: can set serial communication baud rate, 2400/4800/9600/19200/38400/11520 0
• Speed scale: can set speed range of PTZ (only take effect when using serial communication), standard/expand
• Speed 1imi t: can set on/ off of pan-tilt speed and lens magnification linkage

PTZ settings

PTZ settings Submenu

• DZ oom: on/of f
• Focus mode: auto/manual
• Remote speed: PTZ speed 1-16 (only takes effect when using IR remote controller)
• Pan direction: can set pan direction normal/reverse
• Tilt direction: can set pan direction normal/reverse
• Flip: can set image flip Mirror: can set image mirroring

Exposure settings

Exposure settings Sub menu

• Full auto: exposure compensation can be adjustable in autom od e, 0-15 Backlight can be adjustable in auto mode, open/off
• Iris pri: iris value can be adjustable in iris priority mode, Close-1/1. 8 exposure compensation can be adjustable in auto mode, 0-15 Backlight can be adjustable in auto mode, open/off
• Shutter pri: shutter value can be adjustable in shutter priority mode, 1/1-1/l0K exposure compensation can be adjustable in auto mode, 0-15 Backlight can be adjustable in auto mode, open/off
• Bright pri: bright value can be adjustable in bright priority mode, 0-27
• Manual: exposure compensation can be adjustable in manual mode, 0-15 iris value can be adjustable in manual mode, Close-1/1. 8 shutter value can be adjustable in manual mode, 1 / 1- 1 / l 0K

White balance settings

White balance settings Submenu

• White balance mode: auto, manual, indoor, outdoor, one push, ATW
• Manual mode: red gain is adjustable, 0- 255 blue gain is adjustable, 0-255

Settings

Picture Settings Submenu

• 2DNR: 2D noise reduction, open/off
• 3DNR: 3D noise reduction, off / 1- 5
• Contrast: can set image contrast, 0-15
• Chroma: can set image color saturation, 0-15
• Acutance: can set image sharpness value, 0-15
• Gamma: can set image gamma, 0-4
• WDR: can set wide dynamic range, off/1-6
• Defog: can set defog level, off/1-15
• Flicker: anti-flicker frequency, off/50hz/60hz

Network information

Network information Sub menu

• Can check network information of camera.
• Can manually edit the camera IP address, mask, and gateway by using “0-9” of the IR remote controller when DHCP is off.

System setting

System setting Sub menu

• Resolution: can set 108 0 p50 / 60 / 59. 94, 108 0 i 60 / 59. 94 / 50, 108 0 p30 / 29. 97 / 25, 720 p60 / 50.

• Reload preset 1: on/off, if preset position 1 is set for the camera, can set to call the preset position 1 function automatically after powering on,
• Rs485: RS485 search function, on/off
• Language: can set menu language, simplified Chinese/traditional Chinese/English
• Version: current version of the camera, can be used by a manufacturer to confirm the version information, without special functions
• Factory reset:
• Reset system, restore only parameter values except for image and network parameters to factory default values
• Reset picture, restore image parameter value to the factory default value
• Reset Net, restore network parameter value to the factory default value
• Reset all, restore all parameter values to factory defaults

Connection

Direct connection mode: Connect the camera directly to the computer with a network cable. Network connection mode: Connect the camera to the Internet network, and access the network through a router or switch. Users can log in to the device through the browser. The computer must have the network segment where the camera IP is located. If the network segment is not added, you will not be able to log in. If the default IP address of the camera is 192.168.1.118, you need to add 1 network segment to the computer. The specific method is as follows:

First, open the computer network local connection properties window, select Internet Protocol Version 4 (TCP/ IPv4)n double click or click the property Internet Protocol Version 4 (TCP/ IPv4) n, enter the properties window, and click advanced to enter advanced TCP/ IP Set the IP address and subnet mask in the IP address field. After the addition is complete, click OK to complete the IP network segment addition. Users can add corresponding network segments according to their modified camera IP address.

WEB login:
Enter the device IP address in the browser address bar to default to 192. 168.

1. 118, and press Enter to enter the web client login interface. Enter admin in the [User Name] field, enter admin in the [Password] field, and pass the verification to enter the background preview interface. Language selection: Select the language icon in the upper right corner of the login interface, and click to select the web interface language type.

Image preview
After logging in successfully, enter the management interface. The default is to enter the video preview interface. On the left side of the preview interface, in the image preview area, you can click to output the mainstream, sub-stream, and the display ratio of the screen output (16:9 & 4:3) and full- screen display function.

PTZ control:
On the right side of the preview interface, the PTZ control area can specifically implement the following functions: The gimbal rotates upward, the gimbal rotates downward, the gimbal turns to the left, the gimbal rotates to the right, the gimbal restores the initial center position, the lens zooms out, the lens zooms in and the preset position number is set. Number O starts counting, which is preset position 1; saves the preset position currently set; deletes the corresponding preset position; calls the corresponding preset position. Click “Settings” in the upper right corner to enter the software parameter configuration interface. There are mainly the following options: video configuration, network configuration, system configuration, etc.

Video configuration

video coding

• Encoding mode: Set the video compression format. The default primary/secondary stream compression format is H. 264/H. 265.
• Stream: Set different video output modes and use different streams. Contains primary and secondary streams. The primary stream is optional 19201080, 1280720, and the secondary stream is optional 1280720, 1024576, 640*360.

Configuration

• Rate (Kb/s): Set the video bit rate (the default stream is 4096Kb/s; the default stream is 2048Kb/s; 0-15360Kb/s is optional)
• Frame rate: set the video frame rate, the default frame rate is 30frames
• Rate Control: Set the stream control mode, the primary/secondary stream default variable bit rate (CBR), support for selectable bit rate (VBR)
• I frame interval: set the keyframe interval, the primary/secondary stream defaults to 30, 1-100 is optional.

Image parameter
The image parameter interface allows you to make the following adjustments to the image effects:

• Focus: You can set the focus mode, focus distance, and digital zoom on and off Exposure: Set exposure mode, shutter speed, anti-flicker, gain, aperture and brightness
• White balance: white balance mode, red and blue gain effect can be set
• Image: can set mirror, flip, backlight compensation, gamma curve, wide dynamic, and other functions
• Picture quality: can set the screen brightness, sharpness, contrast, saturation and other functions
• Noise reduction: can be set to enable 2D noise reduction, 3D noise reduction

Audio setting
The audio setting interface can adjust the following parameters on audio:

• Audio encode: audio function can be set, on / off
  Audio type: set audio format, AAC
  Sampling: set audio sampling rate, 22050/32000/44100/48000 Moderate (Kbps): set the audio code rate, 32/48/96/128
  Save: After the audio parameters are modified, click the “Save” button to save the modified parameters, the web interface will prompt accordingly

RTMP setting:
The RTMP setting interface can adjust the following parameters on RTMP:

• RTMP state: control switch of the mainstream, on/off control switch of sub-stream, on / off
• Main RTMP address: fill in the live data upload address of the live platform in this column (e.g. fill in the youtube RTMP
• address, rtmp://a.rtmp. youtube. com/live2/y4f7-rgmc-bzer-0vs2), which means the mainstream is used to stream on Youtube live platform;
• Sub stream RTMP address: fill in the live data upload address of the live platform in this column (e.g. fill intheYoutube RTMP
• address, rtmp://a. RTMP. youtube. com/live2/y4f7-rgmc-bzer-0vs2), which means the sub stream is used to stream on the Youtube live platform; §ave: ,,after the RTMP streaming parameters are modified, click Save button to save the modified parameters, the web interface will prompt accordingly

Network Configuration

Ethernet parameters

• DHCP: Set whether to enable automatic IP acquisition. Close by default
• IP address: Set the IP address. The default is 192. 168. 1. 118, where IP is the address of the login web page.
• Subnet mask: Set the subnet mask (default is 255. 255. 255. 0)
• Default Gateway: Set the default gateway (default is 192. 168. 1. 1)
• HTTP port: set the HTTP port, the default is 80
• Web port: Set the web port, the default is 6087
• Main stream port: Set the mainstream video acquisition port. The default is 554.
• Secondary stream port: Set the secondary stream video acquisition port. The default is 554.

System Configuration

• Version upgrade: The page displays version information, which can only be read by the user and cannot be modified.
• File upgrade: Click the upgrade icon, in the pop-up window, select the upgrade fi1e; c1ick Upload upgrade, after the upgrade is successful, the device automatically restarts.
• Note: Ensure that the power and network of the device are properly connected during the upgrade process, otherwise the upgrade wi11 fai1.
• Restore factory: You can select “Simple Recovery” to reset the image parameters, select “Full Recovery” to reset and restart all parameters, and select “Restart” to restart the device directly.
• Account setting: You can modify the user name and password of the login management account. After modification, you need to restart and login again.

Technical parameter

0/59.94,720p60/50

Signal| PAL/NTSC
Lens| 12X optical zoom| 20X optical zoom
Foci| f=3.9mm(W)～46.8 mm(T)| f=4.7mm(W)～94.0 mm(T)
Horizontal View Angle| 72.5°(W)～23.9°(T)| 58.7°(W)～3.2°(T)
Focus System| Auto/Manual
Minimum Illumination| 0.1Lux
Exposure Control| Auto/Manual
Shutter| 1/1～1/10000s
Gain| Auto/Manual
White Balance| Auto/Indoor/Outdoor/Manual
Image Effect| Full color/black and white/image flip
S/N Ratio| ≥50db
Pan| 355°(max.speed:80°/s)
Tilt| -30°to  +90°(max.speed:60°/s)
Video Output HD| HDMI/3G-SDI/USB 2.0/RJ-45
Power| 12V DC(10.8～13.0V DC)
Control protocol| SONY VISCA、PELCO P/D
Network protocol| VISCA over IP、 RTSP、RTMP、ONVIF； NDI (optional)
Control Mode| RS-232C、RS-422/485、USB Control

Accessories

| DC 12V power adapter, IR Remote, Operation manual, RS-232C Cable, HDMI cable， USB

cable， Ceiling bracket

0/59.94,720p60/50

Signal| PAL/NTSC
Lens| 20X optical zoom| 30X optical zoom
Foci| f=4.7mm(W)～94.0mm(T)| f=4.3mm(W)～ 129.0mm(T)
Horizontal View Angle| 59.5°(W)～3.3°(T)| 63.7°(W)～2.3°(T)
Focus System| Auto/Manual
Minimum Illumination| 0.4Lux| 0.35Lux
Exposure Control| Auto/Manual
Shutter| 1/1～1/10000s
Gain| Auto/Manual
White Balance| Auto/Indoor/Outdoor/Manual
Image Effect| Full color/black and white/image flip
S/N Ratio| ≥50db
Pan| 355°(max.speed:80°/s)
Tilt| -30°to +90°(max.speed:60°/s)
Video Output HD| HDMI/3G-SDI
Power| 12V DC(10.8～13.0V DC)
Control protocol| SONY VISCA、PELCO P/D
Control Mode| RS-232C、RS-422/485、USB Control

Accessories

| DC 12V power adapter, IR Remote, Operation manual, RS-232C Cable, HDMI cable， USB

cable， Ceiling bracket

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>