RODSUMWIRELESS AC-BLE-T110G Wireless Beacon with Vibration Detection User Manual

June 5, 2024
RODSUMWIRELESS

RODSUMWIRELESS AC-BLE-T110G Wireless Beacon with Vibration Detection

Specification

AC-BLE-T110G:

Mechanics Data

Size| Approx. 60.3 x 43.3 x 21.1 mm
Weight| Approx. 25 grams (without Battery) Approx. 34 grams (with Battery)
Casing| PC/ABS Case
Electrics Data
Bluetooth Chip| Nordic nRF52840
Frequency| 2.4GHz
Memory| 256kB Ram, 1MB Flash


BLE Version

| Bluetooth 5 compatible iBeacon compatible

BT4.2 Advertise Mode supported

Long Range (PHY Coded) Mode supported

G-force| Build-in 12-bits 3-Axis Digital Accelerometer
Input/ Output| 1 Digital Input for Magnet Door Switch, Flood Detection 1 Digital Output reserved
Interface| I2C interface for external device
Battery| Non-rechargeable Battery CR2477 (3V 1000mAh)
Life Time| Base on different interval and power setting
Transmission Range| Up to 200m (with Long Range PHY Coded Mode)
Environmental Conditions
Operating Temperature| -25°C to +75°C
Waterproof Rating| IP68
Material Resistance| UV resistance

Extended Battery Compartment

Size Approx. 81.8 x 61.3 x 36.6 mm
Weight Approx. 54 grams (without Battery)
Casing PC/ABS Case
Battery 2 x C-Type 1.5 Batteries Appr. 5000mAh
Waterproof Rating IP68
Material Resistance UV resistance

Function Description

LED Indicator Status

LED Status Description
Stay Off Beacon Power Off
Stay On Beacon in Configuration Mode, connected with mobile
Flash 1600ms Off 400ms On Beacon Under Configuring Mode, not connected with

any mobile
Flash 4990ms Off 10ms On| Beacon Under normal Advertising Mode

LED Indicator description Table

Battery Level Reporting

User can enable/ disable the Battery Level Reporting by Aroco Beacon Config APP.
If the function is enabled, the upper 4 bits of Major will be covered by Battery Level in advertising data.
It will increase Beacon power consumption.
The Battery Level bits table is shown as below:

Battery Level Upper Bits value
~10% 4096
~20% 8192
~30% 12288
~40% 16384
--- ---
~50% 20480
~60% 24576
~70% 28672
~80% 32768
~90% 36864
~100% 40960

Battery Level bits value Table

Double Advertise Mode

User can enable/ disable the Double Advertise Mode by Aroco Beacon Config APP.
If the function is enabled, beacon will advertise same data packet twice to increase the data receiving stability.
It will increase Beacon power consumption.

BT4.2 Advertise Mode

Normal Advertise Mode with Bluetooth 4.2 for around 50 meters transmission range.
User can choose to advertise data by Normal BT4.2 Advertise Mode, Long Range (PHY Coded) Mode, or both Normal and Long Range Mode by Aroco Beacon Config APP.

Long Range (PHY Coded) Mode

Advertise Mode with Bluetooth 5 for long range (around 200 meters) transmission range. It request more transmission time per data and increase Beacon power consumption. RODSUMWIRELESS AC-BLE-T110G Wireless Beacon with
Vibration Detection FIG 1

Advertising Timeline in a different mode

Motion Detection

Users can enable/ disable the Motion Detection by Aroco Beacon Config APP.
If the function is enabled, beacon will monitor the motion detection alarm from Accelerometer with the threshold and duration setting. Alternative UUID, major and minor value will be reported instead of normal advertising. RODSUMWIRELESS AC-BLE-T110G Wireless Beacon with Vibration Detection FIG
2

Motion Detection Function flow chart

Software Configuration

Android App Start up Instruction

  1. Download and install the AROCO BEACON CONFIG Android App (version 1.4.10) from following QR Code URL: RODSUMWIRELESS AC-BLE-T110G Wireless Beacon with Vibration Detection FIG 3Android version: 5.1 or upper RODSUMWIRELESS AC-BLE-T110G Wireless Beacon with Vibration Detection FIG 4*Since the app is installed be APK, notice windows might appear while installation. Press “INSTALL ANYWAY” and “DON’T SEND” to finish the installation process.

  2. Unscrew the screw and open the cover. Fill in battery CR2477 to Turn On the Beacon. RODSUMWIRELESS AC-BLE-T110G Wireless Beacon with Vibration Detection FIG 5

  3. Start the App. Allow Device’s Location permission, Enable Bluetooth and Location. RODSUMWIRELESS AC-BLE-T110G Wireless Beacon with Vibration Detection FIG 6

  4. Press the Change Mode Button on the Beacon board. Beacon will enter configuring mode RODSUMWIRELESS AC-BLE-T110G Wireless Beacon with Vibration Detection FIG 7Indicator Blue LED has different Flashing Rate in different Mode
    iBeacon Mode: Indicator LED Flash 4990ms Off 10ms On Configuring Mode: Indicator LED Flash 1600ms Off 400ms On

    • The Indicator LED will stay On when the Beacon in Configuring Mode and connected the Mobile App
    • Beacon will back to iBeacon Mode for save energy while no any connection over 60 seconds; or press “Disconnect” Button in Mobile APP, press change mode button after Indicator LED flash.
    • Press and Hold the Change Mode Button 5 seconds under iBeacon Mode to restore all above config to default.
  5. Press Magnifier Icon button on the App to scan and connect the Beacon. RODSUMWIRELESS AC-BLE-T110G Wireless Beacon with Vibration Detection FIG 8

  6. Select the Beacon and Tap to connect. All current parameter will be read.

Common Setting Configuration

UUID, Manufacturing Code, Major, Minor, Battery Level reporting, TX Power, Advertising Interval, Advertising type and PIN setting can be checked and updated in this Tab page.
All current setting will be shown on the app once the beacon connection is made.
Beacon will advertising with those setting in normal status. RODSUMWIRELESS
AC-BLE-T110G Wireless Beacon with Vibration Detection FIG
10UUID: Simple 16 characters in simple (simple check box ticked) or 16 Bytes hexadecimal UUID data can be changed. (Default UUID: aa55bb44cc33dd22ee11+6 bytes Beacon MAC address)

  • Non-hexadecimal content will be blocked when Simple check box is un-ticked

  • Simple allowed following characters **0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ-_/,.***

  • If new simple UUID length less than 16 characters, app will fill full stop at the end of new UUID to 16 characters length and updated the parameter when “SET” button pressed.

  • If new UUID length not 32 in non-simple status, the notice will be shown as below when “SET” button pressed. All parameter cannot be updated. RODSUMWIRELESS AC-BLE-T110G Wireless Beacon with Vibration Detection FIG 10Manufacturing Code: 2 Bytes Code data can be changed. Non-hexadecimal content will be blocked. (Default: 0x004C)

  • If new Mfg. Code is empty, the notice will be shown as below when “SET” button pressed. All parameter cannot be updated. RODSUMWIRELESS AC-BLE-T110G Wireless Beacon with Vibration Detection FIG 12Major: Range 0 to 65535 (Default: 0)
    Minor: Range 0 to 65535 (Default: 0)

  • Major and Minor fixed to 0 if UUID is in simple
    Battery Level (Batt lvl): Tick box for choose the data advertising of Beacon Battery Level; Click Button to show the current Battery Level in mV

  • Battery Level reporting will cover the upper 4 bits of Major RODSUMWIRELESS AC-BLE-T110G Wireless Beacon with Vibration Detection FIG 13TX Power (dBm): Combo Box choice include -20, -16, -12, -8, -4, 0, 2, 3, 4, 5, 6, 7, 8 (Default: -12) RODSUMWIRELESS AC-BLE-T110G Wireless Beacon with Vibration Detection FIG 142 x Adv: Tick box for data advertising by Double Advertisement
    Advertising Interval (ms): Range 50-3600000. (Default: 650)

  • If new Adv. Interval is empty or less than 50, the notice will be shown as below when “SET” button pressed. All parameter cannot be updated. RODSUMWIRELESS AC-BLE-T110G Wireless Beacon with Vibration Detection FIG 15Advertising Type: Tick Box to choice Normal Type (BT4.2) or/ and Long Range Type (BT5) (Default: Normal (BT4.2) Type only)

  • Tick both box for choose the both type
    PIN: 4 digits PIN (Alphabet or number) for Login when every connection create (Default: 1234)

  • If new PIN length not 4, the notice will be shown as below when “SET PIN” button pressed. PIN cannot be updated. RODSUMWIRELESS AC-BLE-T110G Wireless Beacon with Vibration Detection FIG 16

  • If PIN value incorrect, the notice will be shown at the bottom as below when connecting the beacon. Those notice message will also be shown in the “LOG” Tab page. RODSUMWIRELESS AC-BLE-T110G Wireless Beacon with Vibration Detection FIG 17Text notice box will be shown at the bottom if any CFG updated. Those notice message will also be shown in the “LOG” Tab page. RODSUMWIRELESS AC-BLE-T110G Wireless Beacon with Vibration Detection FIG 18CONFIG APP will updated all the above parameter to Beacon by press “SET” Button. No any parameter will be updated individually if any input error notice appear.
    GET: All current setting value will be shown on this page when press the “GET” button
    REBOOT: Request beacon reboot when press the “REBOOT” button.
    Connection between beacon and mobile will be lost. Beacon will start will iBeacon mode after reboot. RODSUMWIRELESS AC-BLE-T110G Wireless Beacon with
Vibration Detection FIG 19

Trigger Setting Configuration

Only connected Beacon with G-force Accelerometer will show this Tab page.
Sensor ON/OFF, Threshold, Duration, Repeat Count, Alternative UUID, Alternative Major and Alternative Minor setting will be shown and can be checked and updated.
All current setting value will be shown on the app once the beacon connection is made.
Beacon will trigger the Motion Detection Alarm by advertising with Alternative UUID, Major and Minor according those setting. RODSUMWIRELESS AC-BLE-T110G
Wireless Beacon with Vibration Detection FIG 20

Sensor: Combo Box for Motion detection function Off or On selection. Threshold, duration and repeat count setting will be shown when selected Movement. Motion Detection will be triggered where the threshold and duration higher than the setting value
Threshold (mg): Threshold value for trigger the Motion Detection
Range 63-8000
Duration (ms): Consecutive motion time for trigger the Motion Detection Range 160-20400
Repeat Count: Beacon advertise Alternative information times
Range: 1-5000, or 9999

  • If one of the Threshold, Duration, Repeat Count out of range, the notice will be shown as below when “SET TRIG” button pressed. All TRIG parameter cannot be updated. RODSUMWIRELESS AC-BLE-T110G Wireless Beacon with Vibration Detection FIG 21
  • If Repeat count = 9999, Beacon will keep advertise alternative information instead of normal information until the beacon reboot.

All current TRIG setting value will be shown when press the “GET TRIG” button
Text notice box will be shown at the bottom if any TRIG CFG (Motion Detection) updated. Those notice message will also be shown in the “LOG” Tab page. RODSUMWIRELESS AC-BLE-T110G Wireless Beacon with Vibration Detection FIG
22

Threshold setting will be auto-corrected to a nearest greater value of multiple of 63 when value set to beacon.
Duration setting will be auto-corrected to a nearest greater value of multiple of 80 when value set to beacon.

Alternative Information: Include UUID, Major and Minor. Beacon will advertise that alternative information instead of normal information when motion detection triggered.
Alt. UUID: Simple 16 characters in simple (simple check box ticked) or 16 Bytes hexadecimal UUID data can be changed. (Default alt. UUID: aa55bb44cc33dd22ee11+6 bytes Beacon MAC address)
Alt. Major: Range 0 to 65535 (Default: 0)
Alt. Minor: Range 0 to 65535 (Default: 0)

  • Non-hexadecimal content will be blocked when Simple check box is un-ticked
  • Simple allowed following characters **0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ-_/,.***
  • If new simple UUID length less than 16 characters, app will fill full stop at the end of new UUID to 16 characters length and updated the parameter when “SET” button pressed.
  • If new UUID length not 32 in non-simple status, the notice will be shown as below when “SET” button pressed. All parameter cannot be updated. RODSUMWIRELESS AC-BLE-T110G Wireless Beacon with Vibration Detection FIG 23
  • Major and Minor fixed to 0 if UUID is in simple

All current Alternative information setting value will be shown when press the “GET ALT. UUID” button
Text notice box will be shown at the bottom if any Alt UUID CFG updated.
Those notice message will also be shown in the “LOG” Tab page. RODSUMWIRELESS AC-BLE-T110G Wireless Beacon with Vibration Detection FIG
24

Finish Configuration

Please go to “COMMON” tab page and press “REBOOT” button when every setting is updated. Beacon will reboot immediately, disconnect with mobile APP, and ready to start the beacon normal operation.

Log

All activity will be logged with time and shown on this log tab page. RODSUMWIRELESS AC-BLE-T110G Wireless Beacon with Vibration Detection FIG
25

Rodsum Wireless Limited www.rodsum.com 

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals