GENIE G3T-BX Intellicode 3 Button Remote Garage Opener Transmitter Instructions

Training HomeLink with Intellicode ® Transmitters

Use this process to train the HomeLink device for the following remotes shown below: *If the remote you are using is not shown or this process does not work, see the next section for additional options.

Train HomeLink device to the Remote:

NOTES:

1. Choose an unused button on the HomeLink device that will be used to open the door.

2. Hold the transmitter  2 inches away from the HomeLink device.

3. To clear the HomeLink device completely, see the end of the instruction.

4. Press and hold down any button on the remote AND press and hold  This remote is shown as  HomeLink  Device down the chosen button on the HomeLink device AT THE SAME TIME.   The HomeLink indicator LED blinks slowly at first and then changes to a  faster blink rate ‐ once the blink rate changes too fast (could take up to 20  seconds) – then release both buttons.  Before you proceed, make sure the HomeLink device indicator has stopped blinking completely.

5. When the HomeLink device indicator STOPs blinking, press and hold down the chosen button on the HomeLink device for a full 5 seconds ‐  then release. (Ignore the HomeLink transmitter indicator during those 5 seconds.)

6. Confirm that the HomeLink device picked up the transmission from the remote by pressing the chosen button n the HomeLink device.  The operator head LEDs should light in response.  If the operator LEDs light, continue o the next steps.  If after holding down the HomeLink device button for 5 seconds or longer, the LEDs on the head do not light, repeat step 1 in this section until the operator LED lights to blink in response to the HomeLink device button press.

Program the HomeLink Device to the Opener:

NOTES:  1)  For additional instructions, see the motor vehicle manual, visit www.homelink.com, or visit www.geniecompany.com. 

1. Locate either a square PROGRAM button (PRGM) or a round LEARN CODE button on the opener (ceiling). The location could be anywhere on the cover of the opener or under a lens depending on the model.

2. Put opener into programming mode ‐ the openers programming window will time out after 30 seconds:   ‐  PRGM button ‐ press and hold down until the LED turns blue, then release.  Purple LED begins flashing.   EARN CODE button – press and hold down until the red LED starts flashing, then release.

3. Press and hold down the HomeLink button for 2 full seconds ‐ then release.  Press and hold down the chosen  HomeLink button again for 2 full seconds – then release.  Continue this process until the opener operates.  During this time, LEDs on the HomeLink device continue to blink and eventually change to solid (the opener should be moving by then).

If you have these remotes, please follow the instructions below:

Either of these remotes with a software revision of lower than (but not equal to) 2.03.   Software revisions can be found on the back of these remotes under the visor clip.

Preparing the Remote:

1. Choose a button on the remote that you will use to train the HomeLink device.
   If the LED on the transmitter lights RED, proceed to step 2.
   If the LED on the transmitter lights GREEN – perform the following steps:
   1. Press and hold down this button for approximately 10 seconds or until BOTH A RED  AND A GREEN LED light on the remote – then release the button.
   2. Immediately press the same button again quickly two times.
   3. Press the same button again – the ONLY LED that should light is a RED one. If a GREEN  LED lights, repeat this process again until the only LED that lights at the end of step 1 are red.

2. Continue with step 1 under the “Train HomeLink device to the Remote” section above.

If you need to clear out your HomeLink device:

NOTE:  1)  If at any time you need to start over completely, this process will remove all previously programmed garage door openers from the HomeLink device.

1. Press and hold down the first and third buttons on the HomeLink device until the indicator blinks slowly at first and then fast for 20 seconds – then release both buttons.
   The Genie Company
   One Door Drive

2. Mt. Hope, OH 44660
   Customer Care: 800-354-3643
   www.geniecompany.com

References

• Garage Door Openers and Accessories | The Genie Company
• Homelink

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>