FK Irons Killswitch Foot Switch User Manual

June 5, 2024
FK Irons

killswitch Foot Switch
User ManualFK Irons Killswitch Foot Switch

SAFETY NOTICE

CLASS III SYMBOL
A Class III appliance is designed to be supplied from a separated/safety extra-low voltage (SELV) power source. The voltage from a SELV supply is low enough that under normal conditions a person can safely come into contact with it without risk of electrical shock. The extra safety features built into Class I and Class II appliances are therefore ot required. For medical devices, compliance with Class III is not considered sufficient protection, and furthermore, stringent regulations apply to such equipment.

TECHNICAL DATA

Charging Voltage: 5 V
Charging Current: 250 mA
Connection: (1)USB-C
Ambient Temperature: +10 to +35 *C
Relative Humidity 30 to 75%
Dimensions (W x H): 92.2 mm x 20.8 mm
Weight: Approx. 105 g

DEVICE OVERVIEW

FK Irons Killswitch Foot Switch| FK Irons
Killswitch Foot Switch - KILLSWITCH
---|---

THE KILLSWITCH

Key Features

  • Tap to toggle power on the connected device via Bluetooth.
  • Long-lasting rechargeable battery.
  • No moving parts.
  • Bluetooth is enabled and can be paired with the Darklab app for firmware updates.*
  • LED indicator for battery charge.
  •  LED indicator for feedback when tapped.
  •  Power button to turn ON/OFF and reset the device.
  • USB-C connector to recharge the battery.
  •  Nonslip surface.

Note: The Killswitch will not connect to the app when another device is connected, and cannot be controlled via the Darklab app. It’s only meant to link the device.

FK Irons Killswitch Foot Switch 1

Instructions

Pairing: To pair your device, simultaneously press and hold the up and down voltage buttons until LED is pink. When the device finds the killswitch the led turns blue and when it’s verified that the device found the killswitch, it will flash green once, and then each tap will be blue to verify the connection.
To temporarily disable the Killswitch: Press and hold the device power button until the LED turns pink, and to reconnect the Killswitch, press and hold the Power button until the LED turns Pink.
To desynchronize Killswitch: Simultaneously press and hold the up and down voltage buttons till the LED turns pink and then flashes blue, press the voltage down button, and once red LED will flash indicating Killswitch is unsynchronized. Pairing with the app: Scan for nearby devices, and select the Killswitch to pair.
Pairing Darklab Device: Scan and select the device
you wish to be controlled by the Killswitch. On the app’s device control screen, select the settings menu, then select Killswitch. Make sure sync is turned on.
The Killswitch will connect to the device that’s on, and only one device can be connected at a time. It will disconnect from devices that are OFF or charging.
If you have two LightningBolts, you can pair the same Killswitch to both batteries, however, both devices cannot be connected at the same time. Devices will automatically disconnect from Killswitch when charging.
FK Irons Killswitch Foot Switch - Opertion

Killswitch operation: Operating the Killswitch is user-friendly and easy to use. Just tap the device to toggle power.
Button operation:
Press and hold the power button for 10-15 seconds to turn the Killswitch OFF. Press and hold the power button for 5-9 seconds to turn the Killswitch ON. Press and hold the power button for 3-5 seconds to RESET your Killswitch.

Charging operation: Lift rubber plug and connect energized USB-C plug to charge your device. When USB-C is powered, the green LED light will turn ON and remain solid until the battery is completely charged. Once the Killswitch battery is fully charged, the green LED light indicator will turn OFF.
Using a Darklab charger and cable is highly recommended for optimum results. Be sure to charge your machine for 5 hours before use.
FK Irons Killswitch Foot Switch - Charging operation

Note: This device is not waterproof or water resistant. Please ensure no liquids penetrate the device.
The use of FK Irons barrier film is highly recommended.

ADDITIONAL INFORMATION

WARRANTY
Darklab warrants that the device will perform efficiently when used as intended. Should this product prove to be defective due to manufacturing issues, Darklab will repair/replace the device – free of charge. This warranty will be void if the device shows signs of having been tampered with, disassembled, handled roughly, dropped, overexposed to moisture or damaged to sensors resulting in compromised functionality.

HANDY TIPS
The following tips will help you get the most out of your Killswitch and avoid potential issues:

  • Only use approved power adapters, failure to do so can void your warranty.
  • Use only quality cables. A good connection will ensure consistent performance.
  • Keep safe using Killswitch-approved barrier film. Typical adhesives could interfere with sensors.
  • Use only FDA-approved cold sterilization solutions for disinfection.
  • NOT AUTOCLAVABLE.

TROUBLESHOOTING

1.- Killswitch manufacturer
FK Irons: 1771 NW 79th Avenue, Doral, Florida 33126
2.- Firmware
It’s important to keep the firmware on your Killswitch updated. Download the Darklab App for your I phone to receive updates and notifications about software updates.
For service inquiries, please contact service@fkirons.com. For additional tips and tutorials, please visit our FKIrons Youtube channel.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals