SOONWELL Element G900 Bi Color Bowens Mount LED Mono Light User Manual

SOONWELL Element G900 Bi Color Bowens Mount LED Mono Light 

FCC COMPLIANCE STATEMENT

This device compiles with Part 15 of the FCC Rules. Operation Is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

[Warning] Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits fora Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses,and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

• If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a different circuit than the receiver is connected to.
• Consult the dealer or an experienced radio/TV technician for help.

RF WARNING STATEMENT
This device has been evaluated to meet general RF exposure requirements.

PACKING LIST

Please make sure all accessories listed below are completed before using. If not, please contact with your sellers immediately.

* Tips: The illustrations in the manual are only diagrams for reference. Due to the continuous development of new versions of the product, if there are any differences between the product and the user manual diagrams, please refer to the product itself.

PRODUCT DETAILS 

Control Box 

SETTING UP THE LIGHT

Attaching/detaching the Protection Cover

1. Attaching/detaching the Protection Cover
   Press down the lock pin and rotate the cover clockwise to detach the cover. Fix the cover into the Bowens mount and rotate the cover counter-clockwise to attach the cover.
   Notice; Always remove the protection cover prior when turning on the light. Always re -install the cover when packing it away.

2. Attaching/detaching the Hyper-Reflector
   Fix the reflector into the Bowens mount and rotate it counter-clockwise to attach the Hyper-reflector.
   Press down the lock pin and rotate the Hyper-reflector clockwise to detach it .

Notice: Installation methods of other bowens mount accessories are similar to this, please refer to the above inst31lation methods.

Setting Up the Lamp Head

1. I.Attaching/detaching the U-Jack
   Both of the V-locks on the U-jack need to be retained close status, if not, following the arrow on the picture, press down the plate to release the locking pin.
   Hold up the lamp, place it into the V-locks on the U-jack, the V-lock will lock down the lamp automatically, lamp set up finished.
   Press down the V-lock plates on the U-jack, unlock the lamp, hold up & release the lamp from the U-jack.

2. Fix The Lamp Head
   The tilt angle of the lamp body can be adjusted through the ratcheting disk brake handle. Loosen the ratcheting disk brake hand le, adjust the lamp head to a suitable angle, and rotate it to fix it.

3. U-jack Setting Up on Light Stand
   Hold up the U-jack, put its spigot onto a light stand, screw in the thumb knob and fix the U-jack on the light stand.

4. Setting up the Handle Grip
   Press down the locking button on the top of the handle,slid in or out to assemble/disassemble the handle on the top or the end of the lamp.

Setting Up the Control Box

1. lnstall the control box to the light stand.
   Mount and fix the quick release eta mp on a light stand by rotating the handle on the clamp; fix in and lock the control box on the clamp by its V-lock plate.

Connect The Light Head And Control Box

As the picture, connect the Light head and control box with connecting cable.

Tips:

1. Press down the unlock pins on the connectors before plugging in/out. Do not pull out the connector before pressing  down its unlock pin!
2. Use the original lamp cable for the connection only! Contact us if the cable got lost or damaged.

Powered

AC POWERED

Battery-powered

Tips: In battery power mode, to protect the batteries being damaged, the maximum output power of the lamp is limited to be 300W.
Battery power mode functions only when the both of the 2 batteries attached.
Compatible with 14.8V output voltage Li-ion batteries.

Operation Guide

G900 integrated with 4 control methods: Button control, Bluetooth{APP} Control, Wired DMX Control.Only 1 of the 4 controls can be applied to the lamp at a time.

Manual Control

1. Start /CCT mode
   Powerand switch on the controt box. Its normal working startup display will be shown as following
   

CCT Mode

Quick press on the [DIAL KNOBI to enter CCT parameter setting. quick press again on the knob to move the selection cursor to next parameter. Rotate on the knob to adjust the selected parameter.

Parameter Range

• Brightness (DIM): 196 to 100%
• Color Temperature (CCT): 2600K to 6000K
• Curve (CURVE): Linear, logarithmic

“DIAL KNOB” Rotating Function
Move selection cursor or parameter settng; rotating clockwise to increase value or decrease value on counter-clockwise.

Menu Mode
In unlock mode, press the [MENUj button, rotate the knob and move the cursor on the setting list, press the knob to enter selected setting: EFFECTISET- LCDISET-FUNCISYS TEMP

Effect Mode
In effect mode, rotste the [DIAL KNO B) to view the light effect, short press the [DIAL KNOB) to select the light effect, continue to
press the [DIAL KNOB] to enter the light effect page, and adjust the brightness and frequency parameters.

Parameter Range
8 pre-set FX: STORM, CYCLE, JUMP, FLASH, PAPARAzZi, BAD BULB, TV, EXPLOSsiON.
Brightness: Adjusta ble from 1% to 100%
Speed: adiustable range 01-20

SET-LCD
Inthe display SET-LCD, rotate the [D IAL KNOB] to move the cursor, press [Dial wheel] to enter the selected menu, and rotate the [DIAL KNOB} to adjust the display parameters
Parameter Range
“SDIM”-Brightness: Adjustable range from 1to 10
“SCR”-Contrast: Adjustable range from l to 10
“STD”-Delay: Timing of LCD backlight turns off when no operation on the buttons, 30s, 60s, 120s,-(steady lit).

SET-FUNC
Rotate the (DIAL KNOB] to switch menus, press DIAL KNOB) to select a menu, and then rotatethe {DIAL KNOB) to set the
parameters of the selected menu, and press [DIAL KNOB) again to jump to the next menu.
Parameter Range
“LANG”-Language: Chinese or English. “ADD” DMXAddress: 001 to 511. BT”-Bluetooth. open or close “MODE”-M/S: master or slave

System Temperature

You can check the product temperature in this mode.
Parameter Range
Temperaturel means temperature of the control box
Temperature 2 means temperature of the lamp head

DMXConsole Control

1. DMX Standard Console connected with S0ONWELL G900 spotlight control box

Menu Mode
In unlock mode, press the [MENUJ button, rotate the knob and move the cu rsor on the setting list, press the knob to enter the selected setting: EFFECTISET- LcDSET-FUNCISYS TEMP

Effect Mode
in effect mode, rotate the [DIAL KN08] to view the tight effect, short press the [DIAL KNOB] to select the light effect, continue to
press the [DIAL KNOB] to enter the lighteffect page, and adjust the brightness and frequencyparameters.
Parameter Range
8 pre-set FX: STORM, CYCLE, JUMP, FLASH, PA PARAZZI, BAD BULB, TV, EXFLOS ION.
Brightness: Adjusta ble from 1% to 1009%
Speed: adiustablerange 01-20

SET-LCD
In the display SET-LCD, rotate the [D IAL KNOB) to move the cursor, press [Dial wheell to enter the selected menu, and rotatethe
[DIAL KNOB) to adjust the display parameters
Parameter Range
SDIM”-Brightness: Adjustable range fro m 1 to l0
“SCR”-Contrast: Adj ustable range from l to 10
“STD”-Delay: Timing of LCD backlight turns off when no operation on the buttons, 30s, 60s, 120s,–(steady lit)

SET-FUNC
Rotate the [DIAL KNOB) to switch menus, press {DIAL KNOB] to select a menu, and then rotatethe [DIAL KNOB] to set the
parametersof the se lected menu, and press [DIAL KNOB) again to jump to the next menu.
Parameter Range

• “LANG” Language: Chinese or English.
• “ADD DMXAdd ress: 001 to 511.
• “WIFI: open or close
• “BT”-Bluetooth: open or close
• “MODE”-M/S: master or slave
• “WF”-Wifi Chanel: 0-7.

System Temperature
You can check the product temperature in this mode.
Parameter Range

• Temperature 1 means temperature of the control box
• Temperature 2 means temperature of the lamp head

DMX COnsole Control

1. DMX Standard Console connected with S0ONWELL G900 spotlight control box
2. OMX standard console is connected with SOONWELL G900 spotlight control box, ST series and other SOONWELL series lights.
3. Signal Channel and Address Description
   G900 spotlight has 2 DMX signal channels, Channel definiti on: N(DIM), N+L{CCT).
   DMX address setting range: 001-51. In DMX control mode, the brightness and color temperature of the lights can only be adjusted
   through the DMX console. Fit for single or multiple G900 spotlights.
   When controlling multiple G900s independently, offset the DMX address of each light by 2 chan nels. (flight A is set to DM001,
   then light B is set to DM003 so that A and B can be controlled separately on the DMX controller.)

Product Parameters

Warranty

1. Malfunctions caused by water in the lamp are not covered by warranty.
2. If the G900 was used in rainy day, it would bebetter & safer to use the lamp within the ti angle range as below:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>