JBC RHN-A Rework Hand Support for PHNK Instruction Manual

www.jbctools.com
RHN
Rework Hand Support for PHNK
INSTRUCTION MANUAL

This manual corresponds to the following reference:

Packing List

RHN-A

Hand
Support Arm …………….. 1 unit
Ref. HRR-A| Height
Adjustment Flange …. 1 unit
Ref. 0023991| Shaft …………………… 1 unit

Base PHN compatible ………………………. 1 unit| Headless Screw ………………………………… 1 unit
Ref. 0017057

Allen Key …………………………………………….. 1 unit
Ref. 0013609| Manual ………………………………………………… 1 unit
Ref. 0027888

Features

Assembly

Setting up the Hand Support Arm
Fit the shaft into the base bushing

1.  and tighten the headless screw
2. Then assemble first the height adjustment flange
3.  and finally the hand support arm
4. onto the shaft.
   The hand support arm position should be as shown in the image.
   The right-hand support is marked at its bottom side with the letter “R”.

Height Adjustment

According to your work needs the hand support arm allows adjustment for different heights through the vertical axis.
Slide the arm to the appropriate height

1. and secure it by tightening the knob
2. to guarantee stability.

Work Position Adjustment

RHN arm allows adjustment for different positions according to your work needs. The articulated arm covers all work areas.

The correct hand work position is shown in the following images:

Preheater Positioning

RHN has been designed to work together with PHN
Fit PHN onto the positioning bolts (1) for a proper alignment. The four corner guides (2) help to place the heater unit in its position. If a fixed preheater position is not wanted the positioning bolts can be removed with a screwdriver.

Note: For each preheater size there are different rework hand supports with different base dimensions available.

Accessories*

If second-hand support is needed, Left Hand Support HRL is available. HRL also allows adjustment for different positions.

In case of using both left and right arms, assemble both as shown in the illustration according to the letters on the back of the hand support, to keep the hand supports at the same level.

* Not included, sold separately.

Compatible JBC Articles*

HRR and HRL can be combined with RWT, RWS, or RWB.
Assemble first the height adjustment flange (1), then the HRR (2), and afterward the HRL (3). Assemble the second height adjustment flange (4) and finally the RWT (5).

4 different sizes for PCB Supports are available:

Maintenance

• Check periodically that RHN is clean, especially the sliding parts and the shaft.
• Use a damp cloth when cleaning. Alcohol can only be used to clean the metal parts.|
• Replace any defective damaged parts. Use original JBC spare parts only.

 Not leave up RHN over the preheater when the preheater is working.

Safety

It is imperative to follow safety guidelines to prevent electric shock, injury, fire, or explosions.

•  Do not use the equipment for any purpose other than PCB rework.
• The temperature of accessible surfaces may remain high after the unit is turned off. Handle with care.
• Be careful with the fumes produced when soldering.
• Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal harm.
• Not leave up the arms directly above heat surfaces.
• Utmost care must be taken with liquid tin waste which can cause burns.
• This appliance can be used by children over the age of eight as well as persons with reduced physical, sensory or mental capabilities or lacking experience provided that they have been given adequate supervision or instruction concerning the use of the appliance and understand the hazards involved. Children must not play with the appliance.
• Maintenance must not be carried out by children unless supervised.

Notes

————————————————————————————————————————————–

————————————————————————————————————————————–

————————————————————————————————————————————–

Specifications

RHN
Rework Hand Support for PHNK
Ref.: RHN-A

– Base Dimensions:
– Total Height:
– Arm Heigth:
– Arm Lenght:
– ESD Connector
– Total Net Weight:
– Package Dimension / Weight:
(L x W x H)| 310 x 239 mm / 12.20 x 9.41 in
205 mm / 8.07 in
200 mm / 7.87 in
498 mm / 19.61 in
4.50 kg / 9.92 lb
370 x 204 x 370 mm / 6.09 kg
14.57 x 8.03 x 14.57 in / 13.43 lb
---|---

Complies with CE standards
ESD Safe

Warranty
JBC’s 2 year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labour.
The warranty does not cover product wear or misuse.
In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased.

This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must be collected and returned to an authorized recycling facility.

www.jbctools.com
0027888-190522

Documents / Resources

| JBC RHN-A Rework Hand Support for PHNK [pdf] Instruction Manual
RHN-A Rework Hand Support for PHNK, Rework Hand Support for PHNK, Support for PHNK
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>