HAGOR WM55H ST SA Flip II Mobile Stand System Instruction Manual
- June 11, 2024
- HAGOR
Table of Contents
HAGOR WM55H ST SA Flip II Mobile Stand System
Product Information
The product is a TV stand with a rolling base, front shelf, and TV bracket. It comes in two sizes: ST SA Flip II 55 (Art.-Nr.: 5787) and ST SA Flip II 65 (Art.-Nr.: 5788). The product is designed to securely hold a TV and provide flexibility in terms of its placement.
Safety Indication
Technical devices are valuable and should be handled with care during
installation. It is important to protect the components and secure the
installation area to prevent injuries and material damage. The materials
included in the scope of delivery may not be suitable for the installation
site, so it is recommended to check in advance and replace them with suitable
materials if necessary. If unsure about the installation, please contact the
manufacturer or trained specialists.
Scope of Delivery
- Rolling base components
- Fixing bolts
- TV bracket components
- Tilting plates
- AV shelf (for ST SA Flip II 55 only)
Product Usage Instructions
-
Installation of the Rolling Base (Step 1)
Start by assembling the rolling base components according to the instructions provided. Once the base is assembled, attach it to the bottom of the TV stand. -
Installation of the AV Shelf (Step 2)
If you have the ST SA Flip II 55, you can install the AV shelf.
Note that it can only be used in the lower position with the ST SA Flip II 65. Attach the shelf to the front of the TV stand using the components provided. -
Installation of the TV Bracket (Step 3)
Attach the TV bracket to the back of the TV stand using the components provided. Note that there are different fixing bolts for the ST SA Flip II 55 and the ST SA Flip II 65, so make sure to use the correct ones. The length of the screw depends on the hole depth of the TV, so measure in advance. -
Installation of the Fixing Bolts (Step 4)
Insert the fixing bolts into the TV bracket and adjust them to the correct depth using the adjustable rings. Again, make sure to use the correct bolts for your specific model of TV. -
Tilt Settings (Step 5)
To adjust the tilt of the TV, remove the screws and washers from the tilting plates and assemble them. Attach them to the TV bracket using the screws and washers provided.
Dimensions
The dimensions of the product vary depending on the size and model. Please
refer to the instructions and diagrams provided for accurate measurements.
Caution!
- Technical devices are of considerable value. You should therefore handle the components carefully during installation and protect them if necessary.
- If necessary, the installation area should also be secured. Falling parts can cause injuries and material damage.
- The materials included in the scope of delivery may not be suitable for the special conditions at the installation site. Please check this in advance and replace it with suitable materials if necessary.
- If you are unsure about the installation of the product or have any questions, please contact us or other trained specialists.
Safety indication
-
Do not use the stand on sloping floors.
-
Do not use the stand near stairs or floors with gradients.
-
Do not use the stand on external or rough floors that could damage the wheels.
-
The installation should be performed by competent personnel.
Scope of delivery
Installation
Installation of the rolling base
Installation of the front shelf
Please note! The AV shelf can only be used in the lower position with the ST SA Flip II 65″.
Front view
Installation of the TV bracket
Installation of the fixing bolts | ST SA Flip II 55“
Length of the screw depends on the hole depth of the TV. Please measure in advance.
Installation of the fixing bolts | ST SA Flip II 65“
Length of the screw depends on the hole depth of the TV. Please measure in advance.
Disassembly of the securing bracket
Remove the safety bracket (L).
Tilt settings
Remove the screws and the washers. Assemble the 2 tilting plates (B).
Fix them with the screws and the washers.
Tilt settings
Mount and secure the screen | ST SA Flip II 55“
Hang up the screen. Please note! Please perform this work stept in pairs. Make sure that the bolts are correctly inserted into the keyholes. Replace the securing brackets and screw them tight.
Mount and secure the screen | ST SA Flip II 65“
Hang up the screen. Please note! Please perform this work stept in pairs. Make sure that the bolts are correctly inserted into the keyholes. Replace the securing brackets and screw them tight.
Function test and adjustment
Try the rotation several times and make sure the screen is securely locked
with the safety brackets (L)
If necessary, increase or decrease the force of the spring by adjusting the
screw (S).
Dimensions | ST SA Flip II 55“
Dimensions | ST SA Flip II 65“
HAGOR Products GmbH | Oberbecksener Straße 97 | D-32547 Bad Oeynhausen | Telefon: +49(0)57 31-7 55 07-0 | Mail: hagor@hagor.de
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>