SYMA 720p Positioning Aerial Drone Adjustable Camera User Manual
- June 7, 2024
- SYMA
Table of Contents
USER MANUAL
**MAIN FEATURES
**
- Utilizes the 4-axis structure, enabling the drone to be even more flexible, speedy, and possessing a relatively stronger wind-withstanding capability. It is suitable for both spacious indoor and outdoor areas.
- Built-in 6-axis gyro stabilizer to ensure the accuracy of in-flight position.
- The structure uses a modular design which makes it easier to install and repair.
- With the functions of outdoor GPS fixed-point, one key return, auto-return when the drone is out of control or in low-voltage, one key ascent/descent, geomagnetic headless, position hovering mode and 4 channels function which are up/down, rise/decline, turn left/right, forward/backward, left/right side flight, follow me, circle flight.
- HD wifi real-time transmission for getting the fun of different photography.
The material, specifications, or pads within the package are for reference only. All instructions and other collateral documents are subject to change at the sole discretion of SYMA Co., Ltd. For up-to-date product literature, visit www.symatoys.net.
Safety Guide
- Please store the smaller-sized drone accessories in places that are out of reach of children.
- This drone is very powerful. For all first-time flights, the left joystick must be slowly pushed up in order to prevent the drone from ascending too fast to avoid unnecessary collision and possible damage and injury.
- When the flight is ended, first turn off the power of the remote control. Then turn off the power of the drone.
- Avoid placing the batteries in places with high temperatures and exposure to heat.
- Take extra precautions to ensure that the drone is at a minimum distance of 15 feet from the pilot, other people, and animals in order to prevent bodily injury during flight operations. A minimum separation distance of 20 cm must be maintained between the user’s body and the device under normal use conditions.
- This drone is for people ages 12+. It must be flown always within the line of sight of the pilot(or instructor) and flown safely.
- Non-rechargeable batteries are not to be recharged; Batteries are to be inserted with the correct polarity; Different types of batteries or new and used batteries are not be mixed.
- When the drone is not in use, please remove the batteries from the remote control.
- The supply terminals are not be short-circuited.
- Discharge the battery to 40%-50% (On a full charge, fly for half of the total flight time) if it will not be used for 10 days or more, this can greatly extend the battery life.
- Please keep a safe distance from the spinning propellers to avoid injury.
- To ensure the electromagnetic environment requirement of the aviation radio (station), using remote controls in the zone, which is in a radius of about 5000m zones from the circle center of the airport runway, is forbidden. All users also should abide by the regulation of the radio set forth by government and regulatory agencies including the duration and area.
- Only uses the recommended transformer for the model, and the transformer is not a model. Disconnect the transformer from the model which is available cleaning with liquids before cleaning. Check the cord, plug, enclosure, and other parts of the transformer regularly. If any damages have been discovered, please immediately stop using it, until it was completely repaired.
- Never look steadily at the laser beam since the laser radiation.
- Attention:Drone assembly under adult supervision.
- The pilot is responsible for the safe operation and safe distance from uninvolved persons and property on the ground and from other airspace users and shall never fly the drone above crowds (> 12 persons).
- Open the battery cover of the toy with a screwdriver.
- The packing has to be kept since it contains important information.
Repair and maintenance
1. Use a dry and soft cloth to clean this product.
2. Avoid exposing this product to heat.
3. Do not immerse this product in water, otherwise, the electronic parts will
be damaged.
4. Transformers used with the toy are to be regularly examined for damage to
the cord, plug, enclosure, and other parts, and that, in the event of such
damage, the toys must be used with this transformer until the damage has been
repaired.
Package description
The following items can be found in this product package:
● Drone
● Remote Control
● User Manual
● 4 Blades
● USB Charger
● 4 Protective Gears
● Mobile Phone Retaining Clip
Blade and Protective Gear’s Installation Methods
Blade’s installation
Press the blade lockdown, and then the blade “A” is rotated in A clockwise
direction to remove, and it is locked in A counterclockwise rotation;The blade
B is rotated in A counterclockwise to remove, and it is locked in A clockwise
rotation.
Protective Gear’s Installation
1. Insert the protective gear into the two jack connectors
underneath the main body as shown in Figure 1.
2. Insert the stem on the protective gear into the jack connector on the main
body as shown in Figure 2 and press it.
Camera’s Installation and Dismantling Methods
Installation steps for the camera
1.Connect the camera’s wire connector to the drone.
2.Place the camera into the drone and rotate the camera counterclockwise to
lock.
Dismantling steps for the camera
1. Rotate the camera in a clockwise direction.
2. Take out the camera upward and disconnect the wire connector
from the drone.
Installation of Mobile Phone Retaining Clip
Mobile phone retaining clip’s attachment method:
1. Pull up the phone clip cover from behind the remote control.
2. Insert the phone clip holder into the connector at the top of the remote
control.
3. Press the handles to adjust the jaws.
Battery Charging and Charging Methods for Drone
1. Press the power button on the top of the drone to make sure the drone is
turned “OFF”.
2. Press the fixed components at the bottom of the battery and pull out the
battery.
3. Insert the USB port of the USB charging cable to the power supply and the
red indicator light will turn on, while the battery is inserted for charging
the green indicator light will turn on, and it will turn off when charging
completed.It takes about 150 minutes to completely charge the battery.
Note : charging input voltage must
be 5V (input current 2A shall be accurate, input current size will directly
affect charging time), The change of charging indicator light shall prevail.
4.After charging completed, replace the battery with the drone.
The charging time is less than 150 minutes; In hover flight conditions longer
than 12 minutes!
Precautions as follows during charging of battery:
– Avoid placing the active batteries in places with direct exposure, sunlight,
and high temperatures. For example, naked light or electrical equipment
installations; otherwise it may cause damages or explosions.
– Avoid immersing the batteries in the water. The batteries shall be stored in
a cool and dry place.
– Avoid dismantling the batteries.
– During the charging of the battery, avoid leaving the charging place.
– Rechargeable batteries are to be removed from the toy before being charged.
– Rechargeable batteries are only to be charged under adult supervision.
– Exhausted batteries are to be removed from the toy.
– Caution:Risk of explosion if battery replaced by an incorrect type, dispose
of used batteries according to the instructions.
Understanding your remote control
Remote control’s button function description:
Battery Installation Method: Open up the battery cover at the back of the remote control. Correctly place 4 x AA alkaline batteries in the battery box in strict adherence to the polarity instructions ( batteries are not included).
1. During the battery installation, it must be ensured that the polarities of
the batteries are matched with that of the battery box. No battery shall be
installed with the opposite polarity.
2. Please do not use new and old batteries together.
3. Please do not use different types of batteries together.
4. Do not use rechargeable batteries.
Flight Preparation and Turning the Drone ON and Off
1. Flight preparation
①Find a wide place for flying.
②Install the battery in the drone, and place it on a level surface with the
nose of the drone face forward(Figure 1), press the power button for 2
seconds, and then release(Figure 2). Power on the remote control, push the
throttle joystick of the remote control up to the top and then down to the
bottom(Figure 3). When the remote control beeps twice and the indicator light
of the drone turns to solid from blink signal connection completed.
2.Compass Calibration:
Before the first flight, compass calibration is required. When the remote
control has connected to the drone, push the left joystick to the right bottom
corner and hold it, then press the One key return button located at the upper
right corner of the remote control (Figure 1). When the indicator lights flash
slowly, release the left joystick and hold the drone horizontally and rotate
360 degrees till the indicators of the drone turn to fast flashing(approx 4
circles) (Figure 2), and rotate it 360 degrees till the indicators turn to
long bright (approx 4 circles) (Figure 3), the calibration finished.
Note:
- Never calibrate the compass in a strong magnetic field or near the bulk metal, such as magnetite, parking lot, and buildings with underground reinforced.
- Never carry the ferromagnetic material, such as a mobile phone, with you when calibrating.
- Take a compass calibration when the drone drifting or swinging around during the flight.
3.Search satellite (indoor flight can’t search satellite)
The rear lights of the drone begin as solid orange and turn to blink green
about1 a minute later when finishing the satellite signal searching. After 5
seconds, the blink green lights change to solid green, which indicates there
are enough GPS points recorded successfully, and the drone is able to fly off
the ground with GPS fix-point function.
4. Turning on the drone
Method 1: Push the left joystick (throttle) to the highest point and then back
to the center,of the drone the blades start rotating slowly.
Method 2: Push the left and
right joysticks to the bottom inner corners for 1 second, the blades of the
drone start rotating slowly.
Method 3: When the drone is stationary, press button B, the drone automatically takes off and hovers at a certain height.
1. If the drone is out of the
range of the flight, the indicator light will flash slowly, and then slow
down.
2.When the remote control is switched off or the power is cut off, the drone
will automatically slow down to stop. In the process, open the remote control
to control again.
5. Turning off the drone
Method 1:Push the left joystick (throttle) to the lowest level and hold for 2
to 3 seconds, the drone can then be turned off.
Method 2:Push the left and right joysticks to the bottom inner corners for 1 second, and the drone can be turned off.
Method 3:When the drone is in flight, press button B, the drone will descend to the ground and land.
Drone Controlling Diagram
Direction control
Ascending and descending control
When the
left joystick (throttle) is pushed upwards or downwards, the drone will ascend
or descend correspondingly. Forward and backward control
When the
right joystick (rudder) is pushed upwards or downwards, the drone will fly
forward or backward correspondingly.
Left turning and right turning control
When the left joystick
(throttle) is pushed towards the left or right, the drone will turn left or
right correspondingly.
Trimming operation
Forward and backward trim control
If the drone automatically flies forward/backward while hovering, press in
the left joystick and at the same time push the right joystick
backward/forward slightly to fine-tune the direction. Don’t release the left
joystick until the drone is flying in a stable state.
Left/right
side flight trim control
If the drone automatically flies towards the left/right side while hovering,
press in the left joystick and at the same time push the right joystick
right/left slightly to fine-tune the direction. Don’t release the left
joystick until the drone is flying in a stable state.
Product Features
1. One Key Return:
When using the one key return function (Figure 1) or the drone auto-return
when it is out of control or in low-voltage, the front and rear lights turn
red, and the drone will return home immediately if it at the range of 20
meters, if the drone is beyond the range of 20 meters, it will ascend at about
25 meters altitude first, then return home, and the drone will back to the
record point at last. Long press the one key return button again, the drone
will exit return mode except it is auto return with low-voltage, but when the
drone flies to the second range it can be canceled return(Figure 2) When the
drone returns home, manual operation to avoid obstacle is allowed, and it will
continue to return if stopped manual operation. The return point will be a few
errors caused by the environment, it’s a normal phenomenon.
Note :
1.When the GPS signal is weak or not work, the green light of the drone will
turn orange, and it will fail to return home and get the GPS coordinates, and
it needs to be controlled to return home manually.
2.When the drone is low-voltage, stop other operation and control it to
return, otherwise, it will fall down or crash when over low-voltage.
2. Low-voltage protection:
When the drone encounters direct impact from a foreign object or is
obstructed, or the blades are not rotating, the drone will go into the over-
current protection mode.
3.Over-Current Protection:
When the drone encounters direct impact from a foreign object or is
obstructed, or the blades are not rotating, the drone will go into the over-
current protection mode.
4. Level Calibration Function:
Place the drone on a level surface and at the same time, push both left and
right joysticks to the lower right corners for 2 to 3 seconds; the indicator
lights on the drone will blink rapidly, and they will return to solid status
after about 2 to 3 seconds. The level calibration is successful.
5. High/Low-Speed Function:
Low speed by default when first powered on. Possible to switch the function
mode of high/low speed by pressing the right joystick for a short time. It is
switched into a high-speed mode when two ”beep” sounds come from the remote
control, pressing the right joystick for a short time under fast speed mode
and then one “beep” sound would come from the remote control, then it is
switched back into low-speed mode.
6.Photo/ Video Shooting Function:
①Photo shooting function: Press the Photo button, the drone indicator and the
red indicator light on the camera will flash once when the photo has been
taken.
② Video shooting function: Press the Video button, the drone indicator and the
red indicator light on the camera will flash twice, and then turn long bright,
it indicates the video is recording, press the Video button again, the
indicator light on the drone is long bright, indicating the recording is
complete.
7. Adjustable function of the camera
As shown on the right, press the button A or B to adjust the camera angle in
corresponding upward or downward.
8. GPS Coordinates & Aerial Photography :
After the drone complete recording the return point, it can take aerial
photography at the fixed point accurately, the camera will able to take the
photo or record the video by adjusting the camera angle up and down at the
range of 0-90 degree.
In the wide place, the flying range is more than 180 meters, and the Limit
height of the GPS coordinates is about 35 meters.
9. Auto Hover Function:
After using the left joystick (throttle) to control the ascending/descending
flight of the drone, release the left joystick (throttle) and the drone will
hover at that height when the joystick is released.
10.
Headless Function:
① Defining forward direction:
● Press on the power button of the remote control.
● Connect the
battery to the drone, press the power button of the drone, and adjust the
specified direction f the drone’s head under the headless mode as the new
forward direction.
● Push the left joystick (throttle) on the remote control up to the farthest position and then pull down to the farthest position. When the remote control issues a long “beep” sound, it means the frequency and defining forward direction functions are completed.
2. Toggling between headless function and normal function:
● After the drone is matched with the corresponding frequency, the drone would
be in the normal pattern by default. At this time the indicator light on the
drone would be in a state of on for a long time. After pressing in on the
right joystick of the remote control for 2 seconds, the remote control would
make a sound of “beep, beep, beep” to show that it has entered into a state
of headless mode. Press in the right joystick for 2 seconds then a long sound
of “beep” would be heard to show an exit status. (When under the state of
headless mode, four indicator lights on the drone flash slowly once every four
seconds).
● Under the headless mode, the operator does not need to differentiate the
head position of the drone and only needs to control the drone’s direction
front/back/left/right by using the right joystick direction on the remote
control.
③. Calibration for the
definition of the front:
When the drone encounters a direct impact with foreign objects in the headless
mode, if there is an occurrence of deviation of the defined direction, it is
only required to push both the left and right joysticks to the bottom left
corners simultaneously after placing the flying direction of the drone in the
correction position. When the led light indicator of the drone is in a long
“ON” mode after slowly flashing for 3 seconds, it indicates the calibration.
11.Wireless Real-Time
Transmission Function
①Downloading the installation software
For Android phones, download and install the SYMA FLY APP by visiting
www.symatoys.com or by scanning the QR code. For
IOS Apple phones, download and install the SYMA FLY APP by visiting the App
Store or by scanning the QR code.
Tips: QR codes are provided on the packaging box and at the bottom of the
user manual. Please visit website www.symatoys.com or the App Store/Google
Play to obtain the newest SYMA FLY App.
② For more information on the connection, see the APP operating instructions.
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
“This device complies with FCC radiation exposure limits set forth for the
general population (uncontrolled exposure). This device must not be collocated
or operating in conjunction with any other antenna or transmitter.”
Decoration of Conformity inserts: “Hereby, Guangdong Syma model aircraft
industrial co.,ltd, declares that this drone is in compliance with the
essential requirements and other relevant provisions of Directive 2014/53/EU.”
A copy of the full DoC is attached.
Accessories /Parts List (Optional)
You can choose your favorite optional accessories as below. In order to make it easier for the customers to choose and purchase, we have specially offered each and every accessory. The accessories can be purchased through local distributors. Please kindly specify the colors during your purchase.
Product Descriptions
NO. | Product Name | Qty. | NO. | Product Name | Qty. | NO. | Product Name | Qty. |
---|---|---|---|---|---|---|---|---|
01 | Top main Body | 1 | 09 | Landing Gear | 4 | 17 | switch | 1 |
02 | Bottom main Body | 1 | 10 | Lamp Cover | 4 | 18 | Ornament | 1 |
03 | Blade(Clockwise Direction) | 2 | 11 | Light Bar | 4 | 19 | Light guide part | 1 |
04 | Blade(Counterclockwise Direction) | 2 | 12 | Camera | 1 | 20 | Top cover | 1 |
05 | Protective Gear | 4 | 13 | Motor seat | 4 | 21 | Blade lock | 1 |
06 | Battery | 1 | 14 | Upper Light Bar | 4 | |||
07 | Motor(Counterclockwise Direction) | 2 | 15 | Receiver Board | 1 | |||
08 | Motor(Clockwise Direction) | 2 | 16 | Battery box | 1 |
Main Specifications
Drone’s
Length: 375mm
Drone’s Width : 375mm
Drone’s Height: 110mm
Motor’s Model : Ø10×20
Battery : 7.4V 1000mAh lithium battery
Rectification Procedures
Problem | Reason | Solution |
---|---|---|
The drone has no response | 1. The drone has entered into low-voltage |
protection.
2. When the power of the remote control is weak, the power light indicator
will blink.| 1. Charge up the drone.
2. Change the batteries of the remote control.
The flight response of the drone is not sensitive| 1. The power of the remote
control is weak.
2. There is an interference with the same frequency as that of the remote
control.| 1. Change the batteries.
2. Change to a place where there is no interference with the same frequency.
The drone is flying towards its side in one direction during hovering| 1. The
drone is not calibrated level to the ground.| 1. Re-adjust the calibration
until the drone is level to the ground. For further details, see No.4 on Page
9 for details(Level calibration function).
In the headless state, it is biased towards the front direction| 1. Many
collisions may cause the head to drift.| 1. Re-define the front direction.
For further details, see No. 10 Page 10 for details(Headless function).
Fixed high instability / up and down movement| 1.The drone is not calibrated
level to the ground. 2.Unstable air pressure under severe weather conditions.
3. Violent collision resulting in data disorder of gyroscope.| 1.Re-adjust the
calibration until the drone is level to the ground. For further details, see
No.4 on Page 9 for details(Level calibration function). 2. Avoid flying under
severe weather conditions. 3. Make level adjustment again, see No.4 on Page 9
for details (Level calibration function).
http://www.symatoys.com/downshow/syma-fly-android-apk.html
Manufacturer
Guangdong Syma Model Aircraft Industrial Co., Ltd.
The Crossing of No.2 West Xingye Road and North Xingye Road, Laimei.
Industrial Park Chenghai District Shantou City Guangdong China.
Contact person:SYMA Telephone:+86 0754 86381898
The company has the right of final interpretation
of this instruction manual statement.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>