Falcon FEMS901D1W1 100 Wireless Waterproof Backup Camera User Manual
- June 5, 2024
- Falcon
Table of Contents
FEMS901D1W1 100 Wireless Waterproof Backup Camera
**User Manual
**
FEMS901D1W1 100 Wireless Waterproof Backup Camera
WIRELESS 100% Waterproof Heavy Duty Backup 1080P Camera with Waterproof IP67 7″ LCD USER MANUAL *option to add a second waterproof wireless 1080P camera
PACKAGE CONTENT
INTRODUCTION
Thanks for purchasing our wireless 100% waterproof backup camera. With this manual, you will be able to properly install and operate the unit. Please read this manual thoroughly before operating the unit, and keep it for future reference. This system can add up to 2 wireless cameras.
WHAT IS INCLUDED:
(1) Wireless Waterproof Monitor – (1/2) Wireless IP69 Waterproof backup camera
– (1) LCD Cigarette lighter Power cord
(1/2) Camera power wire – (1) U Dash Bracket Mount for Monitor – (1) Antenna
for Monitor – (1/2) Antenna for Camera
(2) T-Taps – (4) Screws – (1) 3M Commercial Grade Adhesive Tape – (1)
Instruction Manual MONITOR
INSTALLATION:
Dash Mount Installation – U-bracket dash mount and screws along with 3m
adhesive tape for quick install.
MONITOR FUNCTIONS:
Press the M button to enter the menu mode, there are 8 functions here:
Pairing/Picture/MIR-FLIP/Mode/Cam setup/System/Play/Record. FUNCTIONS NOT
USED: PLAY/RECORD FEATURES AS THIS BACKUP SYSTEM DOES NOT RECORD
MONITOR BUTTON FUNCTIONS:
- MODE : Used as the “OK” button
- CH : Touch it to switch between 2 cameras, and camera mode viewing
- Left Arrow : Touch to Navigate Left in menu settings
- M: touch it to enter the menu mode
- Right: Touch to Navigate right in menu settings
- POWER: Press it to power on/off the monitor
LOCK FEATURE:
Touch the M button and hold for seconds till you see the lock icon on the left
upper corner then touch MODE to lock the buttons for waterproof, and unlock it
the same operation.
POWER INSTALLATION:
The monitor can be powered by a cigarette lighter outlet/Ignition switch. The
camera can be powered by a Tail light or a 12V DC power system. Connect the
red wire to the positive and black wire to the ground Choose the camera
location: Drill a 12mm diameter cable hold and secure the camera with two
screws. (package includes screws) Locate the Tail light or 12V DC power system
wiring on your vehicle. Connect the red wire to the positive and the black
wire to the ground or negative.
SUPER-EASY 1-STEP INSTALLATION
PAIRING:
This backup system camera automatically pairs to the LCD once power has been
connected. You may need to manually pair it with the monitor when connecting a
2nd camera or a new camera that replaces the original camera. The manual
pairing steps are the follows Press (M) Menu Button to enter menu mode, then
press 1st icon, pairing mode. Press the Mode Button (OK) button to confirm and
enter this mode. The monitor will start to pair and you will see Pairing Start
on the screen, connect the camera to a power supply. Wait a few seconds for
the image to appear. Press the menu button to return to the previous menu.
FUNCTIONS NOT USED: PLAY/RECORD FEATURES AS THIS BACKUP SYSTEM DOES NOT
RECORD
CAM SETUP: this is the circular function. If this function is turned on,
CAM1 and 2 will switch between camera views. The image of the display on the
top left of the screen is labeled CAM1, CAM2. After this function is turned
on, the monitor cannot adjust the split-screen function.
PICTURE SETTINGS :
Press the M button to enter the menu. In the menu, use the right button key to
enter and select the second icon. picture setting. Touch the left/right arrow
to navigate options. Press the Mode button to confirm and enter this mode
(turns red) setting you to want to adjust. Use left/right arrows to adjust
individual settings.
Note: The system has no volume function
MIR-FLIP:
Rotation options (vertical/Rearview/Front view) Tips: The screen rotation
setting can be switched in a single-camera display only, cannot in split-
screen.
SPLIT-SCREEN MODE:
Press the menu button to enter the menu mode. Use+ button to switch to
split mode setting, press MODE button confirms and enter this mode (in this
mode, you can choose eight different split-screen modes. The last is off icon
means to turn off split mode and enter single screen mode) For example, select
the split-screen of camera 1&2, and then exit the menu button. The screen
displays the split-screen image of cameras 1 and 2 together.
SYSTEM:
In this mode, you can adjust Time(not used) /Language/Auto-DIM/Delay
time/enable_disable backup grid lines
CAMERA ON/OFF:
This function can be used to turn ON/OFF the selected camera in the system
(Confirm that all cameras are ON before setting) For example close CAM1. First
select the CAM1 icon (the CAM1 icon turns yellow). Press the MODE button to
enter this CAM1 (the icon is red now). then use the right arrow button to
switch to OFF, CAM 1 is turned off and the screen will not display the image
of CAM1 (At this time, even if camera 1 was connected and powered on, the
screen will not display the image of CAM 1) Press the MODE button to confirm
and enter this mode. In this mode, you can adjust brightness/contrast/HUE.
Press the menu button to return to the previous menu.
Troubleshoot
- If there is no image after installation, please check whether the monitor has power. Cover the infrared sensor to check if the camera’s infrared lights turn on to confirm if the camera has power. If IR lights are on, unplug and replug the camera to a power source. (see pairing instructions)
- Check the positive and negative wires of the power supply before installation. If the positive and negative poles are connected in opposite directions, the camera will be damaged.
- Sometimes due to the length of the vehicle or driving speed is too fast, the signal may become weak or the image is delayed. Please contact us for a wireless booster.